Olof Johansson wrote: > Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded > over tftp. > > Based on the omap3 evm code. I added a new highlevel define for Tobi > to avoid having it dependent on CMD_NET (which would seem backward in > this case). > > Signed-off-by: Olof Johansson <o...@lixom.net> > --- > > This version of the patch fixes whitespace comments from WD, and includes > fixes for the build warnings that Dirk's patch also silenced. > > > board/overo/overo.c | 62 > +++++++++++++++++++++++++++++++++++++++++ > board/overo/overo.h | 37 ++++++++++++++++++++++++ > include/configs/omap3_overo.h | 23 ++++++++++++++- > 3 files changed, 120 insertions(+), 2 deletions(-) > > diff --git a/board/overo/overo.c b/board/overo/overo.c > index dd6d286..7d87e52 100644 > --- a/board/overo/overo.c > +++ b/board/overo/overo.c > @@ -29,13 +29,19 @@ > * MA 02111-1307 USA > */ > #include <common.h> > +#include <netdev.h> > #include <twl4030.h> > #include <asm/io.h> > #include <asm/arch/mux.h> > +#include <asm/arch/mem.h> > #include <asm/arch/sys_proto.h> > #include <asm/mach-types.h> > #include "overo.h" > > +#if defined(CONFIG_OMAP3_OVERO_TOBI) > +static void setup_net_chip(void); > +#endif > + > /* > * Routine: board_init > * Description: Early hardware init. > @@ -62,6 +68,10 @@ int misc_init_r(void) > twl4030_power_init(); > twl4030_led_init(); > > +#if defined(CONFIG_OMAP3_OVERO_TOBI) > + setup_net_chip(); > +#endif > + > dieid_num_r(); > > return 0; > @@ -76,4 +86,56 @@ int misc_init_r(void) > void set_muxconf_regs(void) > { > MUX_OVERO(); > +#if defined(CONFIG_OMAP3_OVERO_TOBI) > + MUX_OVERO_TOBI(); > +#endif > +} > + > +#if defined(CONFIG_OMAP3_OVERO_TOBI) > +/* > + * Routine: setup_net_chip > + * Description: Setting up the configuration GPMC registers specific to the > + * Ethernet hardware. > + */ > +static void setup_net_chip(void) > +{ > + struct gpio *gpio3_base = (struct gpio *)OMAP34XX_GPIO3_BASE; > + struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE; > + > + /* Configure GPMC registers */ > + writel(NET_GPMC_CONFIG1, &gpmc_cfg->cs[5].config1); > + writel(NET_GPMC_CONFIG2, &gpmc_cfg->cs[5].config2); > + writel(NET_GPMC_CONFIG3, &gpmc_cfg->cs[5].config3); > + writel(NET_GPMC_CONFIG4, &gpmc_cfg->cs[5].config4); > + writel(NET_GPMC_CONFIG5, &gpmc_cfg->cs[5].config5); > + writel(NET_GPMC_CONFIG6, &gpmc_cfg->cs[5].config6); > + writel(NET_GPMC_CONFIG7, &gpmc_cfg->cs[5].config7); > + > + /* Enable off mode for NWE in PADCONF_GPMC_NWE register */ > + writew(readw(&ctrl_base ->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe); > + /* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */ > + writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe); > + /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */ > + writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00, > + &ctrl_base->gpmc_nadv_ale); > + > + /* Make GPIO 64 as output pin */ > + writel(readl(&gpio3_base->oe) & ~(GPIO0), &gpio3_base->oe); > + > + /* Now send a pulse on the GPIO pin */ > + writel(GPIO0, &gpio3_base->setdataout); > + udelay(1); > + writel(GPIO0, &gpio3_base->cleardataout); > + udelay(1); > + writel(GPIO0, &gpio3_base->setdataout);
Use the omap gpio interface described in README.omap3 Tom _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot