Hi Amol
On Wed, Aug 8, 2012 at 12:57 PM, Amol Bhise wrote:
> Hi,
> I need some help resolving system hang when booting from NOR flash (XIP
> boot).
>
> On our system we have CFI NOR flash sitting at base 0x0800. with
> CONFIG_SYS_MONITOR_BASE and TEXT_BASE being set at the flash base address
Hi,
I need some help resolving system hang when booting from NOR flash (XIP
boot).
On our system we have CFI NOR flash sitting at base 0x0800. with
CONFIG_SYS_MONITOR_BASE and TEXT_BASE being set at the flash base address
in board config file. But the system hangs when we actually try to boot
obviously this is OK regardless of my opinion on it ;)
-mike
signature.asc
Description: This is a digitally signed message part.
___
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
On Tuesday 07 August 2012 04:07:52 Bob Liu wrote:
> --- a/arch/blackfin/cpu/initcode.c
> +++ b/arch/blackfin/cpu/initcode.c
>
> if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_BYPASS) {
> serial_putc('e');
> +#ifdef __ADSPBF60x__
> + int i;
> + bfin_write_SEC_GCTL
On Tuesday 07 August 2012 04:07:46 Bob Liu wrote:
> --- /dev/null
> +++ b/arch/blackfin/include/asm/mach-common/bits/spi6xx.h
> @@ -0,0 +1,240 @@
> +/*
> + * Analog Devices SPI3 controller driver
i'd prefer to call it "bfin_spi3" then since it represents the version of the
IP block and not the So
On Tuesday 07 August 2012 04:07:51 Bob Liu wrote:
> Set up uart baud properly for booting u-boot over UART
squash into one of the earlier "initial bf60x support" patches
-mike
signature.asc
Description: This is a digitally signed message part.
___
U-Bo
split & squash into earlier patches where appropriate
-mike
signature.asc
Description: This is a digitally signed message part.
___
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
On Tuesday 07 August 2012 04:07:49 Bob Liu wrote:
> Set up RSI data before sending RSI command if data is applicable.
squash into the "Blackfin: rsi: add bf60x support" patch
-mike
signature.asc
Description: This is a digitally signed message part.
___
please squash into one of the "initial bf60x cpu support" patches
-mike
signature.asc
Description: This is a digitally signed message part.
___
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
On Tuesday 07 August 2012 04:07:47 Bob Liu wrote:
> --- a/arch/blackfin/lib/clocks.c
> +++ b/arch/blackfin/lib/clocks.c
>
> +u_long get_dclk(void)
> +{
> +#ifndef CONFIG_BFIN_GET_DCLK
> + return _get_sclk(&cached_dclk);
> +#else
> + return CONFIG_BFIN_GET_DCLK;
> +#endif
> +}
this looks l
On Tuesday 07 August 2012 04:07:45 Bob Liu wrote:
> --- a/board/bf609-ezkit/Makefile
> +++ b/board/bf609-ezkit/Makefile
>
> +COBJS-$(CONFIG_BFIN_SOFT_SWITCH) += soft_switch.o
is there any reason we *wouldn't* want to build this ? i would just skip
making this an option and always enable it.
a
On Tuesday 07 August 2012 04:07:44 Bob Liu wrote:
> --- a/arch/blackfin/include/asm/mach-bf609/portmux.h
> +++ b/arch/blackfin/include/asm/mach-bf609/portmux.h
this should be part of the initial commit of this header (one of the initial
bf60x support patches)
> --- a/board/bf609-ezkit/bf609-ezki
On Tuesday 07 August 2012 04:07:43 Bob Liu wrote:
> --- a/arch/blackfin/include/asm/config-pre.h
> +++ b/arch/blackfin/include/asm/config-pre.h
>
> #define BFIN_BOOT_16HOST_DMA 11 /* boot ldr from 16-bit host dma */
> #define BFIN_BOOT_8HOST_DMA 12 /* boot ldr from 8-bit host dma */
On Tuesday 07 August 2012 04:07:42 Bob Liu wrote:
> Bf60x support 16K, 64K, 16M and 64M cplb pages, this patch add support for
> them. So that bf609-ezkit can use it's 128M memory.
"it's" -> "its"
> arch/blackfin/include/asm/cplb.h | 13 +-
> arch/blackfin/include/asm/m
On Tuesday 07 August 2012 04:07:41 Bob Liu wrote:
> arch/blackfin/cpu/initcode.c | 96 ++-
> arch/blackfin/cpu/initcode.h |9 ++
> arch/blackfin/cpu/serial1.h| 19 +++
> arch/blackfin/cpu/serial4.h| 3
On Tuesday 07 August 2012 04:07:40 Bob Liu wrote:
> From: Mike Frysinger
>
> Add basic support for blackfin new processor BF60x.
i had always intended to clean & split this 1 change up, but never got a
chance before i left
> arch/blackfin/cpu/cpu.c|4 +-
> arch
Dear Wolfgang Denk.
Please pull from git://git.denx.de/u-boot-sh master.
Best regards,
Nobuhiro
The following changes since commit 6d36121b878a3ccbbff7f60a02109e8c8d81dd0f:
Merge branch 'master' of git://git.denx.de/u-boot-onenand
(2012-08-07 23:42:55 +0200)
are available in the git reposi
On Tue, Aug 07, 2012 at 03:42:45PM -0700, Lucas Stach wrote:
> Am Dienstag, den 07.08.2012, 15:28 -0700 schrieb Allen Martin:
> > On Tue, Aug 07, 2012 at 10:53:00AM -0700, Lucas Stach wrote:
> > > Hi Allen,
> > >
> > > And to answer Tom's question: the failure was that the real U-Boot would
> > >
Am Dienstag, den 07.08.2012, 15:28 -0700 schrieb Allen Martin:
> On Tue, Aug 07, 2012 at 10:53:00AM -0700, Lucas Stach wrote:
> > Hi Allen,
> >
> > And to answer Tom's question: the failure was that the real U-Boot would
> > not come up after the SPL. All I could see was the one line printed by
>
The following changes since commit 8abcd8ab962cd5fb2a4c025e7c7b62a9faf4aa08:
DaVinci DA8xx: fix set_cpu_clk_info() (2012-08-05 22:02:40 +0200)
are available in the git repository at:
git://git.denx.de/u-boot-atmel.git master
for you to fetch changes up to 17cda15fa6fb3ab2433bed951dad5c4ab30
On Tue, Aug 07, 2012 at 10:53:00AM -0700, Lucas Stach wrote:
> Hi Allen,
>
> And to answer Tom's question: the failure was that the real U-Boot would
> not come up after the SPL. All I could see was the one line printed by
> the SPL and nothing more.
I think I found the problem. It's the followi
Dear Markus Hubig,
On 06.08.12 19:48, Markus Hubig wrote:
> This adds support for the AT91SAM9G20 boards by taskit GmbH.
> Both boards, Stamp9G20 and PortuxG20, are integrated in one
> file. PortuxG20 is basically a SBC built around the Stamp9G20.
>
> Signed-off-by: Markus Hubig
> Cc: Andreas Bi
Dear Andreas Bießmann,
On 01.08.12 23:12, Andreas Bießmann wrote:
> The grasshopper board is a avr32 based device and belongs therefore to the
> avr32
> section.
>
> Signed-off-by: Andreas Bießmann
> ---
applied to u-boot-atmel, thanks.
Best regards
Andreas Bießmann
_
Dear Andreas Bießmann,
On 01.08.12 22:56, Andreas Bießmann wrote:
> These boards have ARM cores, move to the ARM section.
>
> Signed-off-by: Andreas Bießmann
> ---
applied to u-boot-atmel, thanks.
Best regards
Andreas Bießmann
___
U-Boot mailing lis
Dear Markus Hubig,
On 01.08.12 21:49, Markus Hubig wrote:
> Signed-off-by: Markus Hubig
> Cc: Andreas Bießmann
> ---
applied to u-boot-atmel, thanks.
Best regards
Andreas Bießmann
___
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mai
On 08/07/2012 02:35 PM, Lucas Stach wrote:
> Am Dienstag, den 07.08.2012, 14:21 -0600 schrieb Stephen Warren:
>> On 08/07/2012 12:19 PM, Lucas Stach wrote:
>>> This allows for two things:
>>> - VBus GPIO may be used on other ports than the OTG one
>>> - VBus GPIO may be low active if specified by D
Dear Lukasz Majewski,
In message <20120806112735.05fd945f@amdc308.digital.local> you wrote:
> Hi Wolfgang,
>
> Please pull following commits:
>
>
> The following changes since commit
> 56249fea3d5e32cddcd9160e51ec93a9c4327c6b:
>
> powerpc/82xx: adapt SDRAM settings for mgcoge3ne (2012-07-31
Warning is:
xilinx_spi.c: In function 'spi_setup_slave':
xilinx_spi.c:81: warning: unused variable 'regs'
Signed-off-by: Stephan Linz
CC: Michal Simek
---
drivers/spi/xilinx_spi.c |1 -
1 files changed, 0 insertions(+), 1 deletions(-)
diff --git a/drivers/spi/xilinx_spi.c b/drivers/spi/xi
Am Dienstag, den 07.08.2012, 14:20 +0200 schrieb Michal Simek:
> Initialize all possible uartlites and return the first
> initialized port. For static configuration is initialization
> done in userial_ports array.
>
> Signed-off-by: Michal Simek
Acked-by: Stephan Linz
Tested with AXI system o
Am Dienstag, den 07.08.2012, 14:20 +0200 schrieb Michal Simek:
> enable serial multi for Microblaze.
>
> Signed-off-by: Michal Simek
Acked-by: Stephan Linz
> ---
> include/serial.h |3 ++-
> 1 files changed, 2 insertions(+), 1 deletions(-)
>
> diff --git a/include/serial.h b/include/ser
Dear Holger Brunck,
In message <1344255393-18421-1-git-send-email-holger.bru...@keymile.com> you
wrote:
> Signed-off-by: Holger Brunck
> cc: Heiko Schocher
> cc: Valentin Longchamp
> cc: Gerlando Falauto
>
> ---
> MAINTAINERS |6 +++---
> 1 files changed, 3 insertions(+), 3 deletions(-)
Dear "Karl O. Pinc",
In message <1344009441-854-1-git-send-email-...@meme.com> you wrote:
> Reference nand monitor commands in U-Boot README
>
> Signed-off-by: Karl O. Pinc
> ---
> Resend of patch to ease review/commit process.
>
> Changes for v2:
> - include a commit message
> - Change mes
Dear Michal Simek,
In message <1344001064-762-1-git-send-email-mon...@monstr.eu> you wrote:
> The patch "spi: tegra2: rename tegra2_spi.* to tegra_spi.*"
> (sha1: edffa63d3d6e76991998789f9fcbaa483731ca65)
> renamed tegra2_spi.c to tegra_spi.c
>
> and the patch "Merge branch 'master' of git://git.
Dear Tomas,
In message
you wrote:
> Dear Wolfgang,
>
> On Wed, Aug 1, 2012 at 9:09 PM, Wolfgang Denk wrote:
>
> > Hm... I have to admit that I am not really happy about such an
> > "explanation". The statement that "other guys" want something is not
> > exactly an explanation of a concept th
Dear Zhong Hongbo,
In message <1342860534-4710-1-git-send-email-bocui...@gmail.com> you wrote:
> From: Zhong Hongbo
>
> all the patitions should depend CONFIG_PARTITIONS, no the
> CONFIG_CMD_$(device). The device symbol may be SATA, SCSI,
> USB, MMC, SYSTEMACE. Or else when the filesystem comman
Am Dienstag, den 07.08.2012, 14:21 -0600 schrieb Stephen Warren:
> On 08/07/2012 12:19 PM, Lucas Stach wrote:
> > This allows for two things:
> > - VBus GPIO may be used on other ports than the OTG one
> > - VBus GPIO may be low active if specified by DT
>
> Hmmm. Why would the board have control
On 08/07/2012 12:19 PM, Lucas Stach wrote:
> This allows for two things:
> - VBus GPIO may be used on other ports than the OTG one
> - VBus GPIO may be low active if specified by DT
Hmmm. Why would the board have control over whether VBUS is asserted if
the port isn't intended to operate in OTG mo
On Tue, Aug 07, 2012 at 10:53:00AM -0700, Lucas Stach wrote:
> Hi Allen,
>
> > Tell me what CodeSourcery version you're using and I'll test it here
> > as well and see if I can reproduce the problem.
> >
> I used CodeSourcery arm-2011.09-70-arm-none-linux-gnueabi to test this.
>
> And to answer
Am Montag, den 06.08.2012, 09:46 +0200 schrieb Michal Simek:
> Prepare for device-tree driven configuration.
>
> Signed-off-by: Michal Simek
>
Acked-by: Stephan Linz
Tested with AXI systems on Avnet S6LX150T and S6LX9 micro-evaluation.
> ---
> v2: Move bi_flashsize and bi_flashoffset from o
Am Montag, den 06.08.2012, 09:46 +0200 schrieb Michal Simek:
> Move board specific function to board_init function in board/ folder
> Remove externs from generic board.c
> Use board_init_f function in board.c file.
>
> Signed-off-by: Michal Simek
>
Acked-by: Stephan Linz
Tested with AXI syst
Hi Michal,
looks fine, but ... (see below)
Am Montag, den 06.08.2012, 09:46 +0200 schrieb Michal Simek:
> microblaze: Fix CONFIG_SYS_HZ usage in board config
>
> Do not use hardcoded value. Use CONFIG_SYS_HZ instead.
> Separate static configuration to single block.
>
> Signed-off-by: Michal Si
Am Montag, den 06.08.2012, 09:46 +0200 schrieb Michal Simek:
> Just coding style cleanup.
> Remove unneeded externs.
>
> Signed-off-by: Michal Simek
> Acked-by: Simon Glass
>
Acked-by: Stephan Linz
> --
> v2: Rebase - depends on previous intc patch
> ---
> arch/microblaze/cpu/interrupts.c
Am Montag, den 06.08.2012, 09:46 +0200 schrieb Michal Simek:
> Return value to find out if un/registration was succesful.
>
> Signed-off-by: Michal Simek
>
> ---
> v2: Add comment to header file to describe parameters and return codes
> ---
> arch/microblaze/cpu/interrupts.c | 1
Am Montag, den 06.08.2012, 09:46 +0200 schrieb Michal Simek:
> Variable is used when CONFIG_SYS_FLASH_CHECKSUM is used.
>
> Warning log:
> board.c: In function 'board_init':
> board.c:101: warning: unused variable 's'
>
> Signed-off-by: Michal Simek
>
Acked-by: Stephan Linz
> ---
> v2: Use
Am Montag, den 06.08.2012, 09:46 +0200 schrieb Michal Simek:
> This is minimum code required to be able to use device-tree
> for u-boot initialization.
> Currently only for device driver initialization.
>
> Linker script change ensures DTB to be aligned
> for both options CONFIG_OF_EMBED and CONF
Dear Stathis Voukelatos,
> Signed-off-by: Stathis Voukelatos
> Cc: Stefano Babic
> Cc: Marek Vasut
> ---
Thanks for the patch and your effort !
btw. how did you find it ? :)
Best regards,
Marek Vasut
___
U-Boot mailing list
U-Boot@lists.denx.de
htt
Dear Tom Rini,
In message <1344358714-14032-1-git-send-email-tr...@ti.com> you wrote:
> The above warning was introduced originally in 436da3c "ext2load:
> increase read speed" and fixed for newer toolchains in b803273 "ext2fs:
> fix warning: 'blocknxt' may be used uninitialized". This change did
Dear Lucas Stach,
In message <1344298788-7059-1-git-send-email-...@lynxeye.de> you wrote:
> As discussed here [http://patchwork.ozlabs.org/patch/158202/] we want to
> use USE_PRIVATE_LIBGCC still.
>
> However commit 5286f1ce dropped it regardless. Adding this back fixes a
> hang while handing ove
Dear Sridhar Addagada,
In message <1344359350.57879.yahoomail...@web162902.mail.bf1.yahoo.com> you
wrote:
>
> Is it possible to compare the contents of the memory location with a
> constant like if test #200010 == 1; then run boot0; else run boot1;fi
Yes, this is possible. For example:
Dear Leif Lindholm,
In message <50214a38.3000...@arm.com> you wrote:
> Most architectures keep the global data pointer (gd) in a register.
This may, or may not be. You should not make any assumptions on how
gd is implemented.
> When using the external app API, because they are calling us rather
Dear Rajesh,
In message
you wrote:
>
> I have MPC8313E-RDB board on which U-boot 1.3.0(along with patches) and
> kernel 2.6.23(along with patches) are running.
>
> Now, i would like to upgrade the kernel from 2.6.23 to 2.6.35.13 with old
> U-boot 1.3.0(along with patches), i am facing problem
This allows for two things:
- VBus GPIO may be used on other ports than the OTG one
- VBus GPIO may be low active if specified by DT
Signed-off-by: Lucas Stach
CC: Stephen Warren
CC: Tom Warren
---
arch/arm/cpu/armv7/tegra20/usb.c | 35 +++
1 Datei geändert, 19
Hi Allen,
Am Dienstag, den 07.08.2012, 10:43 -0700 schrieb Allen Martin:
> On Tue, Aug 07, 2012 at 10:09:00AM -0700, Lucas Stach wrote:
> > Am Dienstag, den 07.08.2012, 11:00 -0600 schrieb Stephen Warren:
> > > On 08/06/2012 06:19 PM, Lucas Stach wrote:
> > > > As discussed here [http://patchwork.
On Tue, Aug 07, 2012 at 10:09:00AM -0700, Lucas Stach wrote:
> Am Dienstag, den 07.08.2012, 11:00 -0600 schrieb Stephen Warren:
> > On 08/06/2012 06:19 PM, Lucas Stach wrote:
> > > As discussed here [http://patchwork.ozlabs.org/patch/158202/] we want to
> > > use USE_PRIVATE_LIBGCC still.
> > >
>
Am Dienstag, den 07.08.2012, 11:04 -0600 schrieb Stephen Warren:
> On 08/06/2012 07:18 PM, Lucas Stach wrote:
>
> There's no description here justifying why you want this change.
>
> I don't think the change is correct; in arch/arm/lib/board.c,
> board_init_r() calls drivers/mmc/mmc.c:mmc_initial
On Mon, Aug 06, 2012 at 11:53:03PM -0700, Albert ARIBAUD wrote:
> Hi Allen,
>
> Also, Allen:
>
> > ---
> > This email message is for the sole use of the intended recipient(s) and may
> > contain
> > confidential inf
I'm using spare bytes of the nvram of the RTC chip to determine which of my two
kernels should be booted. Trying to scrip that in u-boot script I'm doing the
following.
1. Load 200010 with 0 (mw.b 200010 0)
2. Load 200014 with value from nvram (i2c read 68 15 1 200014)
3. if cmp.b 200010 200014 1
Most architectures keep the global data pointer (gd) in a register.
When using the external app API, because they are calling us rather
than we calling them, this register can be corrupted.
The attached (trivial) patch saves the gd pointer at api_init(),
and restores it on every entry to syscall(
Signed-off-by: Stathis Voukelatos
Cc: Stefano Babic
Cc: Marek Vasut
---
Changes for v2:
- White space cleanup
arch/arm/cpu/arm926ejs/mx28/spl_power_init.c | 12 ++--
1 files changed, 6 insertions(+), 6 deletions(-)
diff --git a/arch/arm/cpu/arm926ejs/mx28/spl_power_init.c
Hi,
I have MPC8313E-RDB board on which U-boot 1.3.0(along with patches) and
kernel 2.6.23(along with patches) are running.
Now, i would like to upgrade the kernel from 2.6.23 to 2.6.35.13 with old
U-boot 1.3.0(along with patches), i am facing problem in loading firmware
and ethernet interfaces li
On 08/06/2012 07:18 PM, Lucas Stach wrote:
> Most boards don't need this fixup hook. To avoid a lot of empty
> implementations in board files convert it to a weak symbol.
This seems OK on the surface, but I think there may be more opportunity
for cleanup here.
In board/nvidia/common/board.c, I se
On Tue, Aug 07, 2012 at 02:50:08PM +0400, Ilya Yanok wrote:
> Beaglebone uses SMSC PHY which works incorrectly with generic PHY
> driver so enable SMSC PHY driver to fix networking problems on
> Beaglebone.
>
> Signed-off-by: Ilya Yanok
Applied to u-boot-ti/master, thanks!
--
Tom
signature.
Am Dienstag, den 07.08.2012, 11:00 -0600 schrieb Stephen Warren:
> On 08/06/2012 06:19 PM, Lucas Stach wrote:
> > As discussed here [http://patchwork.ozlabs.org/patch/158202/] we want to
> > use USE_PRIVATE_LIBGCC still.
> >
> > However commit 5286f1ce dropped it regardless. Adding this back fixes
On Sun, Aug 05, 2012 at 07:27:30PM +0200, Javier Martinez Canillas wrote:
> On Sun, Aug 5, 2012 at 12:55 PM, Enric Balletbo i Serra
> wrote:
> > The total RAM size of the IGEP-based boards is 512MiB not 1GiB, the
> > LPDDR memory consist on two dies of 256MiB.
> >
> > Signed-off-by: Enric Balletbo
Hello,
The following changes since commit 8abcd8ab962cd5fb2a4c025e7c7b62a9faf4aa08:
DaVinci DA8xx: fix set_cpu_clk_info() (2012-08-05 22:02:40 +0200)
are available in the git repository at:
git://git.denx.de/u-boot-ti next
for you to fetch changes up to a47233a30055660ad64d865f1fde19503ed0
On 08/06/2012 07:18 PM, Lucas Stach wrote:
There's no description here justifying why you want this change.
I don't think the change is correct; in arch/arm/lib/board.c,
board_init_r() calls drivers/mmc/mmc.c:mmc_initialize() which calls
board_mmc_init(). With this patch, won't this function get
On 08/06/2012 06:19 PM, Lucas Stach wrote:
> As discussed here [http://patchwork.ozlabs.org/patch/158202/] we want to
> use USE_PRIVATE_LIBGCC still.
>
> However commit 5286f1ce dropped it regardless. Adding this back fixes a
> hang while handing over from SPL to U-Boot on Colibri T20.
This proba
The above warning was introduced originally in 436da3c "ext2load:
increase read speed" and fixed for newer toolchains in b803273 "ext2fs:
fix warning: 'blocknxt' may be used uninitialized". This change did not
fix the warning with gcc 4.2, as found in ELDK 4.2.
If we rework the while loop to init
Albert,
Please pull u-boot-tegra/master into ARM master. I've rebased to your
current TOT and slipstreamed in the mkconfig fix. Thanks!
The following changes since commit 8abcd8ab962cd5fb2a4c025e7c7b62a9faf4aa08:
Laurence Withers (1):
DaVinci DA8xx: fix set_cpu_clk_info()
are available
Albert,
> -Original Message-
> From: Albert ARIBAUD [mailto:albert.u.b...@aribaud.net]
> Sent: Monday, August 06, 2012 11:53 PM
> To: Allen Martin
> Cc: Tom Warren; Tom Warren; si...@theia.denx.de; u-boot@lists.denx.de;
> Stephen Warren
> Subject: Re: [U-Boot] pull request for u-boot-tegra
Hi Albert,
please pull from u-boot-imx, thanks.
The following changes since commit 8abcd8ab962cd5fb2a4c025e7c7b62a9faf4aa08:
DaVinci DA8xx: fix set_cpu_clk_info() (2012-08-05 22:02:40 +0200)
are available in the git repository at:
git://www.denx.de/git/u-boot-imx.git master
for you to fe
On 07/08/2012 16:56, Stathis Voukelatos wrote:
> Signed-off-by: Stathis Voukelatos
> Cc: Stefano Babic
> Cc: Marek Vasut
> ---
Applied to u-boot-imx, thanks.
Best regards,
Stefano Babic
--
=
DENX Software Engineering GmbH,
Enable the PL310 L2 cache controller at TRATS Samsung board.
Signed-off-by: Lukasz Majewski
Signed-off-by: Kyungmin Park
Cc: Minkyu Kang
---
include/configs/trats.h |6 --
1 files changed, 4 insertions(+), 2 deletions(-)
diff --git a/include/configs/trats.h b/include/configs/trats.h
i
This patch enables the L1 data cache for systems based on Samsung
Exynos processor.
Signed-off-by: Lukasz Majewski
Signed-off-by: Kyungmin Park
Cc: Minkyu Kang
---
arch/arm/cpu/armv7/exynos/soc.c |8
1 files changed, 8 insertions(+), 0 deletions(-)
diff --git a/arch/arm/cpu/armv7
On Fri, Aug 3, 2012 at 11:05 PM, wrote:
> From: "Mathieu J. Poirier"
>
> Signed-off-by: Mathieu Poirier
> Signed-off-by: John Rigby
Acked-by: Linus Walleij
For this entire series.
Yours,
Linus Walleij
___
U-Boot mailing list
U-Boot@lists.denx.de
Marvell 88E1118R has different uid then 88E1118.
Signed-off-by: Michal Simek
CC: Andy Fleming
CC: Zang Roy-R61911
CC: Kumar Gala
---
drivers/net/phy/marvell.c | 11 +++
1 files changed, 11 insertions(+), 0 deletions(-)
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvel
enable serial multi for Microblaze.
Signed-off-by: Michal Simek
---
include/serial.h |3 ++-
1 files changed, 2 insertions(+), 1 deletions(-)
diff --git a/include/serial.h b/include/serial.h
index 5173499..9475779 100644
--- a/include/serial.h
+++ b/include/serial.h
@@ -31,7 +31,8 @@ extern
Initialize all possible uartlites and return the first
initialized port. For static configuration is initialization
done in userial_ports array.
Signed-off-by: Michal Simek
---
drivers/serial/serial_xuartlite.c | 34 +++---
1 files changed, 19 insertions(+), 15 dele
Beaglebone uses SMSC PHY which works incorrectly with generic PHY
driver so enable SMSC PHY driver to fix networking problems on
Beaglebone.
Signed-off-by: Ilya Yanok
---
include/configs/am335x_evm.h |1 +
1 file changed, 1 insertion(+)
diff --git a/include/configs/am335x_evm.h b/include/co
Dear Stefano Babic,
> On 06/08/2012 23:23, Marek Vasut wrote:
> > Dear Marek Vasut,
> >
> >> The DMA mode didn't properly configure the DMA_ENABLE bit in CTRL1.
> >> Also, it was using SSP0 DMA channel for all SSP devices.
> >>
> >> Signed-off-by: Marek Vasut
> >> Cc: Wolfgang Denk
> >> Cc: St
This i.MX28 platform supports the following:
* 2x FEC ethernet
* USB on USBH0
* I2C EEPROM
* SPI NVRAM
* LEDs
Signed-off-by: Marek Vasut
---
MAINTAINERS |1 +
board/schulercontrol/sc_sps_1/Makefile | 47 +++
board/schulercontrol/sc_sps_1/sc_sps_1.c | 113
Currently patman assumes that there should be only one Signoff line
and this is obviously incorrect: we often have to work with patches
containing other people signoffs. Moreover, it's really desirable
to preserve the comments between signoffs.
So until some sophisticated signoff processing will b
Don't try to sort and uniq changelog entries as this breaks
multiline entries. It will be better to add some real multi-line
support but for now just preserve the entries as is.
Signed-off-by: Ilya Yanok
---
tools/patman/series.py |5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)
di
We already got all changes from git log output and the comment
to the ProcessLine function clearly states that 'patch' mode
is not for scanning tags.
Signed-off-by: Ilya Yanok
---
tools/patman/patchstream.py |3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/tools/patman/pa
Patman is the great tool but I've found it nearly unusable for me.
First of all I need to work with multiple signoffs in commits,
then I'd like to use multiline changelog entries and I accostomed
to putting changelog enties to the bottom of the commit.
These patches fix changelog processing and di
Changes may end in '---' line or Signoff line (generated by
git format-patch) in case of Series-changes: lines being
the last ones in commit message. So detect it properly.
Signed-off-by: Ilya Yanok
---
tools/patman/patchstream.py |6 ++
1 file changed, 6 insertions(+)
diff --git a/tool
On 05/08/2012 12:37, Marek Vasut wrote:
> This i.MX28 platform supports the following:
> * 2x FEC ethernet
> * USB on USBH0
> * I2C EEPROM
> * SPI NVRAM
> * LEDs
>
> Signed-off-by: Marek Vasut
> ---
> board/schulercontrol/sc_sps_1/Makefile | 47 +++
> board/schulercontrol/sc_sps_1/sc_sps
On 05/08/2012 19:31, Fabio Estevam wrote:
> From: Fabio Estevam
>
> On this board, the console is always set to the serial line.
> Do not allow to overwrite it when video is enabled.
>
> Signed-off-by: Fabio Estevam
> ---
Applied to u-boot-imx, thanks.
Best regards,
Stefano Babic
--
==
On 05/08/2012 19:31, Fabio Estevam wrote:
> From: Fabio Estevam
>
> On this board, the console is always set to the serial line.
> Do not allow to overwrite it when video is enabled.
>
> Signed-off-by: Fabio Estevam
> ---
Applied to u-boot-imx, thanks.
Best regards,
Stefano Babic
--
=
The commit
f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls"
removed the config option aimed towards moving that stuff into kernel, which
renders some code unreachable. Remove that code.
Signed-off-by: Jassi Brar
---
arch/arm/cpu/armv7/omap-common/hwinit-common.c |
The commit
f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls"
removed the config option aimed towards moving that stuff into kernel, which
renders some code unreachable. Remove that code.
Signed-off-by: Jassi Brar
---
Hi,
The commit f3f98bb0 seems to suggest we want t
On 07/07/2012 09:25, Marek Vasut wrote:
> The DMA mode didn't properly configure the DMA_ENABLE bit in CTRL1.
> Also, it was using SSP0 DMA channel for all SSP devices.
>
> Signed-off-by: Marek Vasut
> Cc: Wolfgang Denk
> Cc: Stefano Babic
> Cc: Fabio Estevam
> Cc: Andy Fleming
> ---
Whole s
On 05/08/2012 21:05, Otavio Salvador wrote:
> Most code can be shared between i.MX23 and i.MX28 as both are from
> i.MXS family; this source directory structure makes easy to share code
> among them.
>
> Signed-off-by: Otavio Salvador
> ---
Whole series applied to u-boot-imx, thanks.
Best regar
Hi Stefano,
On Tue, Aug 7, 2012 at 12:57 PM, Stefano Babic wrote:
> On 07/08/2012 10:54, Ilya Yanok wrote:
> > Hi guys,
> >
>
> Hi Ilya,
>
> > Is it a good place to post patman patches? Or should I go to some
> chromium
> > list?
>
> IMHO here is the best place, patman is integrated in u-boot an
On 07/08/2012 10:54, Ilya Yanok wrote:
> Hi guys,
>
Hi Ilya,
> Is it a good place to post patman patches? Or should I go to some chromium
> list?
IMHO here is the best place, patman is integrated in u-boot and your
patches can be discussed on this ML - my 2 cents.
Regards,
Stefano
--
===
Hi guys,
Is it a good place to post patman patches? Or should I go to some chromium
list?
Regards, Ilya.
___
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
From: Steven Miao
Add Bf60x resume from hibernate support
Signed-off-by: Steven Miao
Signed-off-by: Sonic Zhang
Signed-off-by: Bob Liu
---
arch/blackfin/cpu/initcode.c | 46 ++
1 file changed, 46 insertions(+)
diff --git a/arch/blackfin/cpu/initcode
From: Mike Frysinger
The static memory controller is how people connect flashes to newer
Blackfin processors, so add knobs for people to program settings if
they so desire.
Signed-off-by: Mike Frysinger
Signed-off-by: Sonic Zhang
Signed-off-by: Bob Liu
---
arch/blackfin/cpu/initcode.h | 51
From: Sonic Zhang
Per the request from ADI Legal.
Signed-off-by: Sonic Zhang
Signed-off-by: Bob Liu
---
arch/blackfin/Clear_BSD.txt| 33
arch/blackfin/cpu/bootcount.c |2 +-
arch/blackfin/cpu/os_log.c |
From: Scott Jiang
Spi driver for bf60x is different from old one, so implement a new
driver for it.
Signed-off-by: Scott Jiang
Signed-off-by: Sonic Zhang
Signed-off-by: Bob Liu
---
.../blackfin/include/asm/mach-common/bits/spi6xx.h | 240 +++
drivers/spi/Makefile
1 - 100 of 115 matches
Mail list logo
