port-based VLANs when mappings
overlapped previous VLANs. Packets destined to a port
not in the default port group flooded all ports.
Tested on a 88E6171 (Linksys EA4500) and 88E6172 ('1900AC)
Signed-off-by: Claudio Leite
---
The indentation looks broken (around HI/LO_SHIFT) but it's a
c
This had been set in r44508 as a workaround for switch
problems.
Now that the switch driver can handle two devices with
the same MAC address in separate VLANs we can go back
to using the same address on both interfaces.
This is the Linksys firmware's default behavior.
Signed-off-by: Cl
Hi,
* drEagle (drea...@doukki.net) wrote:
> I have started to add sysupgrade to guruplug server in kirkwood platform.
> I get stuck in the understanding in my analysis of OpenWrt implementation of
> Ugrade process.
>
> So,
> On the GuruPlugServerPlus are Kirkwood CPU.
> The available NAND (512Mo
* Rob Mosher (nyt-open...@countercultured.net) wrote:
> +++ b/target/linux/mvebu/base-files/etc/init.d/u-boot_env
> @@ -9,6 +9,7 @@ boot() {
> case $(mvebu_board_name) in
>
> armada-385-linksys-caiman|armada-385-linksys-cobra|armada-xp-linksys-mamba)
> fw_setenv auto_recovery
* Rob Mosher (nyt-open...@countercultured.net) wrote:
> Auto recovery is enabled when flashing, so if it goes wrong, you can get
> back to your previous image. Otherwise, I don't think there's a need for it
> as all it does is switch which kernel/root partitions are booted which
> shouldn't ever c
The previous "link" and "status" functions were non-standard,
and thus less useful for parsing.
Signed-off-by: Claudio Leite
---
If accepted this should be also pushed to CC, assuming
that's still possible.
.../linux/generic/files/driver
Signed-off-by: Claudio Leite
---
target/linux/generic/files/drivers/net/phy/mvsw61xx.c | 8
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/target/linux/generic/files/drivers/net/phy/mvsw61xx.c
b/target/linux/generic/files/drivers/net/phy/mvsw61xx.c
index 346acb2..c1e1b9a
The previous "link" and "status" functions were non-standard,
and thus less useful for parsing.
Signed-off-by: Claudio Leite
---
v2: remove enums as well
If accepted this should be also pushed to CC, assuming
that's still possible.
.../linux/generic/files/driver
Also collapses the three identical configurations into one block.
Signed-off-by: Claudio Leite
---
target/linux/mvebu/base-files/etc/board.d/02_network | 10 --
1 file changed, 4 insertions(+), 6 deletions(-)
diff --git a/target/linux/mvebu/base-files/etc/board.d/02_network
b/target
and upgraded from within OpenWrt.
This also adds support for the Linksys dual-image firmware layout
and recovery mechanism.
These patches also transition from a single read-write UBIFS to
squashfs on UBI + UBIFS overlay.
Claudio Leite (7):
kirkwood: enable squashfs-on-ubiblock support
kirkwood
Signed-off-by: Claudio Leite
---
target/linux/kirkwood/Makefile| 2 +-
target/linux/kirkwood/config-3.18 | 2 +-
target/linux/kirkwood/config-4.3 | 2 +-
3 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/target/linux/kirkwood/Makefile b/target/linux/kirkwood/Makefile
index
Linksys uses a dual firmware layout, where the bootloader
will switch to the other stored image when one fails to
boot three consecutive times.
In order to make this firmware compatible with the factory
images and the stock bootloader we must match this layout.
Signed-off-by: Claudio Leite
This is imported verbatim from the mvebu WRT1900AC port.
It picks up the current boot partition from the kernel command line,
then renames that partition "ubi" so that it auto-mounts.
Signed-off-by: Claudio Leite
---
target/linux/kirkwood/config-3.18 | 1 +
ta
This is done with the new image generation system. It also
generates a sysupgrade.tar image.
These images only support squashfs-on-UBI in their present form.
Signed-off-by: Claudio Leite
---
target/linux/kirkwood/image/Makefile | 45 +++-
1 file changed, 39
This is done with existing code from the WRT1900AC port.
It makes sure the "auto_recovery" bootloader option is set,
and resets the s_env boot counter after a successful boot.
This gives users without a serial console connection some
measure of safety.
Signed-off-by: Claudio Leite
--
This automatically writes to the alternate firmware partition
(on Linksys's dual firmware layout) using code borrowed from
the WRT1900AC port.
Signed-off-by: Claudio Leite
---
.../kirkwood/base-files/lib/upgrade/linksys.sh | 79 ++
.../kirkwood/base-files/lib/up
Signed-off-by: Claudio Leite
---
target/linux/kirkwood/base-files/etc/diag.sh | 3 +++
1 file changed, 3 insertions(+)
diff --git a/target/linux/kirkwood/base-files/etc/diag.sh
b/target/linux/kirkwood/base-files/etc/diag.sh
index 716e6c9..89d4655 100755
--- a/target/linux/kirkwood/base-files
Signed-off-by: Claudio Leite
---
This patch is necessary for the "kirkwood: revamp Linksys EA3500 & EA4500"
support" patch series submitted on 6 Nov.
include/image.mk | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/include/image.mk b/include/image.mk
ind
* Imre Kaloz (ka...@openwrt.org) wrote:
> On Sat, 07 Nov 2015 03:29:07 +0100, Claudio Leite
> wrote:
>
> >This patch set reworks support for the Linksys EA3500 and EA4500,
> >integrating significant amounts of code from the WRT1900AC port.
> >
> >Previously th
Signed-off-by: Claudio Leite
---
v2 changes: same as v1
target/linux/kirkwood/Makefile| 2 +-
target/linux/kirkwood/config-3.18 | 2 +-
target/linux/kirkwood/config-4.3 | 2 +-
3 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/target/linux/kirkwood/Makefile b/target/linux
bootloader we must match this layout.
Signed-off-by: Claudio Leite
---
v2 changes: use engineering names
package/boot/uboot-envtools/files/kirkwood | 2 +-
.../linux/kirkwood/patches-3.18/160-ea4500.patch | 64 ++
.../linux/kirkwood/patches-3.18/170-ea3500.patch | 63
Signed-off-by: Claudio Leite
---
v2 changes: new in v2
target/linux/kirkwood/base-files/etc/diag.sh | 4 ++--
target/linux/kirkwood/base-files/etc/uci-defaults/01_leds| 10 +-
target/linux/kirkwood/base-files/etc/uci-defaults/02_network | 4 ++--
target/linux
This is imported verbatim from the mvebu WRT1900AC port.
It picks up the current boot partition from the kernel command line,
then renames that partition "ubi" so that it auto-mounts.
Signed-off-by: Claudio Leite
---
v2 changes: same as v1
target/linux/kirkwood/c
This is done with existing code from the WRT1900AC port.
It makes sure the "auto_recovery" bootloader option is set,
and resets the s_env boot counter after a successful boot.
This gives users without a serial console connection some
measure of safety.
Signed-off-by: Claudio Lei
This is done with the new image generation system and board names.
It also generates a sysupgrade.tar image.
Signed-off-by: Claudio Leite
---
v2 changes: use engineering board names, clean up UBI flags in profile.mk
target/linux/kirkwood/image/Makefile | 45
This automatically writes to the alternate firmware partition
(on Linksys's dual firmware layout) using code borrowed from
the WRT1900AC port.
Signed-off-by: Claudio Leite
---
v2 changes: use engineering board names
.../kirkwood/base-files/lib/upgrade/linksys.sh
Signed-off-by: Claudio Leite
---
v2 changes: use engineering board names
target/linux/kirkwood/base-files/etc/diag.sh | 3 +++
1 file changed, 3 insertions(+)
diff --git a/target/linux/kirkwood/base-files/etc/diag.sh
b/target/linux/kirkwood/base-files/etc/diag.sh
index 0435376..8d48054 100755
Match the engineering board names now used elsewhere.
Signed-off-by: Claudio Leite
---
v2 changes: new in v2
target/linux/kirkwood/image/Makefile | 4 ++--
target/linux/kirkwood/profiles/115-router.mk | 18 +-
2 files changed, 11 insertions(+), 11 deletions(-)
diff
Signed-off-by: Claudio Leite
---
package/boot/uboot-envtools/files/kirkwood | 8
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/package/boot/uboot-envtools/files/kirkwood
b/package/boot/uboot-envtools/files/kirkwood
index 1066371..35cbd84 100644
--- a/package/boot/uboot
Signed-off-by: Claudio Leite
---
The idea here is to benefit from the daily snapshot builds. Since each
device still has its own profile, interested users can still build the
leanest possible build without the few extra packages.
target/linux/kirkwood/image/Makefile | 4 ++--
target
Hi Sebastian,
Two small comments inline.
* Sebastian Careba (nitrosh...@yahoo.com) wrote:
> The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram, 2
> sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and one 5
> ghz antenna.
>
> Signed-off-by: Sebastian Car
Also collapses the three identical configurations into one block.
Signed-off-by: Claudio Leite
---
N.B.: I don't have actual hardware to test this on, but I did
check the syntax by applying the rule to linksys-mamba (which I have).
target/linux/mvebu/base-files/etc/board.d/02_network
Since kernel 3.11, the third parameter passed to notifier_call()
is of type struct netdev_notifier_info. This patch fixes an oops
when setting a netdev LED trigger.
Signed-off-by: Claudio Leite
---
.../patches-3.12/833-ledtrig_netdev-use-notifier-info.patch | 13 +
.../patches-3.13
ay to test that.
Signed-off-by: Claudio Leite
---
.../linux/generic/files/drivers/net/phy/mvsw6171.c | 866 +
.../linux/generic/files/drivers/net/phy/mvsw6171.h | 230 ++
.../generic/patches-3.10/733-phy_mvsw6171.patch| 23 +
.../generic/patches-3.14/732-phy_mvsw6171.
Signed-off-by: Claudio Leite
---
target/linux/kirkwood/config-3.10 | 4 +++-
target/linux/kirkwood/config-3.14 | 4 +++-
target/linux/kirkwood/patches-3.14/160-ea4500.patch | 13 -
3 files changed, 18 insertions(+), 3 deletions(-)
diff --git a
* Claudio Leite (lei...@staticky.com) wrote:
> Any comments are appreciated.
I meant to send this is as an RFC and not a patch.
___
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/open
* Xiongfei Guo (xf...@credosemi.com) wrote:
> Sorry, i missing that, it's Linksys EA4500.
>
> On 07/11/2014 11:53 AM, Xiongfei Guo wrote:
> >Hi, what board you are using?
> >
I also developed and tested on a D-Link DIR-665. I haven't yet submitted
the support files for that board but will do so l
Hello,
* Claudio Leite (lei...@staticky.com) wrote:
> Use pr_debug rather than pr_info since it is only relevant
> for debugging.
>
> Signed-off-by: Claudio Leite
While we are talking about things for Barrier Breaker RC's, could this
patch be merged in? It was marked as accep
* Luca Olivetti (l...@ventoso.org) wrote:
> The problem is that, while the interface shows up in the luci interface,
> I have can see no scan result and when I configure the essid and a wpa
> passphrase it doesn't associate.
>
> Does luci only work with interfaces that support iw (this one doesn't
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.
Signed-off-by: Claudio Leite
---
target/linux/ramips/base-files/etc/board.d/01_leds | 5
Tested only on EA4500.
Signed-off-by: Claudio Leite
---
target/linux/kirkwood/config-3.18 | 335 +
.../linux/kirkwood/patches-3.18/110-ib62x0.patch | 20 ++
.../linux/kirkwood/patches-3.18/130-iconnect.patch | 41 +++
.../linux/kirkwood/patches-3.18/140
This is a swconfig driver for the Marvell 88E6171 switch,
which is a 7-port GigE switch with two CPU ports and 64
802.1q VLANs.
Signed-off-by: Claudio Leite
---
target/linux/generic/config-3.14 | 1 +
target/linux/generic/config-3.18 | 1 +
.../linux
Signed-off-by: Claudio Leite
---
target/linux/kirkwood/config-3.14 | 2 ++
target/linux/kirkwood/config-3.18 | 2 ++
target/linux/kirkwood/patches-3.14/160-ea4500.patch | 13 -
target/linux/kirkwood/patches-3.18/160-ea4500.patch | 13
Signed-off-by: Claudio Leite
---
target/linux/kirkwood/patches-3.18/160-ea4500.patch | 13 -
1 file changed, 12 insertions(+), 1 deletion(-)
diff --git a/target/linux/kirkwood/patches-3.18/160-ea4500.patch
b/target/linux/kirkwood/patches-3.18/160-ea4500.patch
index bf33756..7456b13
This maps the LAN ports to eth0 and WAN port to eth1.
Since there are two interfaces the 802.1q VLAN mode
is unnecessary and left disabled. Port-based VLANs
are used instead.
Signed-off-by: Claudio Leite
---
.../kirkwood/base-files/etc/uci-defaults/02_network | 16
1 file
The '6171 and '6172 are similar enough to work
without any changes to the code.
Signed-off-by: Claudio Leite
---
target/linux/generic/files/drivers/net/phy/mvsw6171.h| 2 +-
target/linux/generic/patches-3.14/733-phy_mvsw6171.patch | 2 +-
target/linux/generic/patches-3.18/733-ph
Recognizes 88E6171/6172/6176 at the moment.
Signed-off-by: Claudio Leite
---
.../linux/generic/files/drivers/net/phy/mvsw61xx.c | 27 --
.../linux/generic/files/drivers/net/phy/mvsw61xx.h | 14 ---
2 files changed, 31 insertions(+), 10 deletions(-)
diff --git a
In preparation for properly supporting switches
beyond the 88E6171.
Signed-off-by: Claudio Leite
---
target/linux/generic/config-3.14 | 2 +-
target/linux/generic/config-3.18 | 2 +-
.../linux/generic/files/drivers/net/phy/mvsw6171.c | 866
Since the driver doesn't know anything about (M)STP
we just hard-set the ports to be enabled if they are
part of the VLAN.
Signed-off-by: Claudio Leite
---
.../linux/generic/files/drivers/net/phy/mvsw61xx.c | 38 ++
.../linux/generic/files/drivers/net/phy/mvsw61xx.h
- eliminate MV_CPUPORT; not necessary since we define
the CPU port(s) via Device Tree
- add STU and expand VTU operations
- update register names to match those of 88E61xx rather than
mvswitch's 88E6060
- use more consistent formatting
Signed-off-by: Claudio Leite
---
.../linux/ge
Necessary for targets using zImage or other kernel
image types.
Signed-off-by: Claudio Leite
---
include/image.mk |5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/include/image.mk b/include/image.mk
index eddf605..e0f12e0 100644
--- a/include/image.mk
+++ b/include
Signed-off-by: Claudio Leite
---
.../linux/kirkwood/base-files/etc/uci-defaults/02_network |3 +++
target/linux/kirkwood/patches-3.14/170-ea3500.patch | 13 -
target/linux/kirkwood/patches-3.18/170-ea3500.patch | 13 -
3 files changed, 27 insertions
Signed-off-by: Claudio Leite
---
package/boot/uboot-envtools/files/kirkwood |4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/package/boot/uboot-envtools/files/kirkwood
b/package/boot/uboot-envtools/files/kirkwood
index c868d07..98f85da 100644
--- a/package/boot/uboot
Previous options resulted in a nonfunctional image.
Signed-off-by: Claudio Leite
---
target/linux/kirkwood/profiles/115-router.mk | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/target/linux/kirkwood/profiles/115-router.mk
b/target/linux/kirkwood/profiles/115-router.mk
te no difference in performance
versus port-based VLANs when the CPU port is not
using tags.
Signed-off-by: Claudio Leite
---
.../base-files/etc/uci-defaults/02_network | 25 ++
1 file changed, 6 insertions(+), 19 deletions(-)
diff --git a/target/linux/kirkwood/base-file
Signed-off-by: Claudio Leite
---
target/linux/kirkwood/profiles/115-router.mk | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/target/linux/kirkwood/profiles/115-router.mk
b/target/linux/kirkwood/profiles/115-router.mk
index f639451..769284f 100644
--- a/target/linux/kirkwood
The VID header offset must be specified explicitly.
Signed-off-by: Claudio Leite
---
target/linux/mvebu/image/Makefile | 7 ---
1 file changed, 4 insertions(+), 3 deletions(-)
diff --git a/target/linux/mvebu/image/Makefile
b/target/linux/mvebu/image/Makefile
index 3512c6a..da7d217 100644
Defaulting to disabled, based on the value of
the (old?) CONFIG_RALINK_USBPHY
Signed-off-by: Claudio Leite
---
target/linux/ramips/rt288x/config-3.18 | 1 +
1 file changed, 1 insertion(+)
diff --git a/target/linux/ramips/rt288x/config-3.18
b/target/linux/ramips/rt288x/config-3.18
index
Signed-off-by: Claudio Leite
---
target/linux/mvebu/base-files/lib/preinit/06_set_iface_mac | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/target/linux/mvebu/base-files/lib/preinit/06_set_iface_mac
b/target/linux/mvebu/base-files/lib/preinit/06_set_iface_mac
index 30f1370
This sets 'enable_vlan' and thus uses 802.1q
VLANs, but without tagging on either interface.
Signed-off-by: Claudio Leite
---
target/linux/mvebu/base-files/etc/uci-defaults/02_network | 3 +++
1 file changed, 3 insertions(+)
diff --git a/target/linux/mvebu/base-files/etc/uc
* Claudio Leite (lei...@staticky.com) wrote:
> This sets 'enable_vlan' and thus uses 802.1q
> VLANs, but without tagging on either interface.
Note: this depends on the previous patch, since setting up the switch
when both interfaces have the same MAC address results in a ton of
p
Toggles the LA bit on the WAN interface.
Signed-off-by: Claudio Leite
---
target/linux/mvebu/base-files/lib/preinit/06_set_iface_mac | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/target/linux/mvebu/base-files/lib/preinit/06_set_iface_mac
b/target/linux/mvebu/base-files
: Claudio Leite
Signed-off-by: Daniel Drown
---
package/libs/openssl/Makefile| 8 +---
package/libs/openssl/patches/110-optimize-for-size.patch | 3 ++-
2 files changed, 7 insertions(+), 4 deletions(-)
diff --git a/package/libs/openssl/Makefile b/package/libs/openssl
Upstream commits 43b68879de27b1993518687fbc6013da80cdcbfe
and ce6031c89a35cffd5a5992b08377b77f49a004b9 improve the
cpuidle driver on Armada XP. The latter commit improves
performance at the slight expense of power consumption.
Signed-off-by: Claudio Leite
---
...uidle-mvebu-Fix-the-CPU-PM
Signed-off-by: Claudio Leite
---
.../206-mvebu_wrt1900ac_use_pwm-fan_rather_than_gpio-fan.patch | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git
a/target/linux/mvebu/patches-3.18/206-mvebu_wrt1900ac_use_pwm-fan_rather_than_gpio-fan.patch
b/target/linux/mvebu/patches
The rt2880 pinmux code from r38026 does not include changes necessary
for the base RT2880 SOC target (rt2880.c) to build. This adapts the
existing code into the latest format.
Signed-off-by: Claudio Leite
---
--- arch/mips/ralink/rt288x.c.orig 2014-02-26 11:41:22.346741653 -0500
+++ arch
Hi Alan,
* Alan.Hoo (huqings...@ycmedia.cn) wrote:
> I've encountered a error during use winscp for login to my router. it's seems
> scp service disbled. what's the name of scp service on OpenWRT ?
>
> PS, the winscp program login successfully but exit very soon.
dropbear supports SCP but not SF
Hello,
I wanted to see if anyone has any RT2880-based hardware that runs
something more recent than AA. I know the current trunk does not build
the base rt2880 target, and I submitted a patch a few weeks ago to fix
that. Even then, the router I have boots but has zero hardware support,
whereas in
Trunk and the latest backport to Attitude Adjustment have the
kmod-rt2800-soc package hidden for the ramips_rt288x target.
This makes the dependency match the dependency given in the
TITLE field.
---
package/kernel/mac80211/Makefile | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --gi
Trunk and the latest backport to Attitude Adjustment have the
kmod-rt2800-soc package hidden for the ramips_rt288x target.
This makes the dependency match the dependency given in the
TITLE field.
Signed-off-by: Claudio Leite
---
package/kernel/mac80211/Makefile | 2 +-
1 file changed, 1
* Flavio Rodrigo LEonel (frleo...@gmail.com) wrote:
> ok man but I'm compiling with the minimum possible, luci + default
> theme ...
> + Basic package ...
Do you have debugging enabled? That can easily push an image over the
limit.
___
openwrt-devel mail
* Flavio Rodrigo LEonel (frleo...@gmail.com) wrote:
> ok my friend what should I do to enable this debugger? would build on
Sorry, I meant to -disable- debugging if you have it on. It's under
"Global build settings" in menuconfig. Uncheck the various 'Compile the
kernel with X' if they are checked
Hi Roman,
* Roman Yeryomin (leroi.li...@gmail.com) wrote:
> This fixes gpio to the state when gpio leds and buttons start to work but
> something still broken for ethernet part (mdio?).
I was actually about to submit a fix for this exact problem. Your GPIO
fix is identical to mine (I actually su
};
};
If necessary, a fixed-link parameter can be specified instead of
phy-handle/phy-mode:
port@0 {
ralink,fixed-link = <100 1 1 1>;
};
Claudio Leite (4):
ramips: enable port init function on RT2880 ethernet
ramips: set wmac
This just enables the existing function, allowing port
settings to be made via the board's DTS.
Signed-off-by: Claudio Leite
---
.../patches-3.10/0218-NET-ralink-init_rt2880_port.patch | 12
1 file changed, 12 insertions(+)
create mode 100644
target/linux/ramips/patches
Probing the wireless device will fail without it, as the rt2800-soc
driver needs to check if the device has a 20MHz clock crystal.
The chip on the RT2880 boards uses 40MHz as far as I can tell.
Signed-off-by: Claudio Leite
---
.../patches-3.10/0219-rt2880_wmac_clock.patch | 21
Use pr_debug rather than pr_info since it is only relevant
for debugging.
Signed-off-by: Claudio Leite
---
.../0220-NET-ralink-squelch_mdio_access.patch | 22 ++
1 file changed, 22 insertions(+)
create mode 100644
target/linux/ramips/patches-3.10/0220-NET-ralink
This patch is made against Roman Yeryomin's previously-submitted,
but not yet merged, rt2880 DT pinctrl patch.
Signed-off-by: Claudio Leite
---
target/linux/ramips/dts/rt2880.dtsi | 8
1 file changed, 8 insertions(+)
diff --git a/target/linux/ramips/dts/rt2880.dtsi
b/target/
* Roman Yeryomin (leroi.li...@gmail.com) wrote:
> On 8 April 2014 19:41, Claudio Leite wrote:
> > * Roman Yeryomin (leroi.li...@gmail.com) wrote:
> > I think by default it configures mdio as mdio--I had a mdio_pins group
> > in my rt2880.dtsi, but when I submitted th
Hello,
* Claudio Leite (lei...@staticky.com) wrote:
> Use pr_debug rather than pr_info since it is only relevant
> for debugging.
>
> Signed-off-by: Claudio Leite
> ---
> .../0220-NET-ralink-squelch_mdio_access.patch | 22
> ++
> 1 fil
. Not sure where
this should go--I put together a quick hack that does this
in the rt2880 GPIO driver and triggered from the DT node.
This works, but any suggestions/comments are appreciated.
Claudio Leite (3):
ramips: Add Airlink101 AR725W board support
ramips: add Airlink101 AR725W use
Signed-off-by: Claudio Leite
---
target/linux/ramips/base-files/etc/diag.sh | 3 +++
target/linux/ramips/base-files/etc/uci-defaults/01_leds| 3 +++
target/linux/ramips/base-files/etc/uci-defaults/02_network | 1 +
target/linux/ramips/base-files/lib/ramips.sh
Signed-off-by: Claudio Leite
---
target/linux/ramips/image/Makefile | 12 +-
tools/firmware-utils/Makefile | 1 +
tools/firmware-utils/src/mkheader_gemtek.c | 211 +
3 files changed, 223 insertions(+), 1 deletion(-)
create mode 100644 tools
Signed-off-by: Claudio Leite
---
target/linux/ramips/dts/AR725W.dts | 113 +
target/linux/ramips/image/Makefile | 3 +
target/linux/ramips/rt288x/config-3.10 | 1 +
3 files changed, 117 insertions(+)
create mode 100644 target/linux/ramips/dts
* John Crispin (j...@phrozen.org) wrote:
> > - GPIOs 8 and 13 (WPS LEDs) do not work. The fix is to turn off bit
> > 6 in the RT2880 SYSTEM_CONFIG register. Not sure where this should
> > go--I put together a quick hack that does this in the rt2880 GPIO
> > driver and triggered from the DT node. Th
Generates webflash-compatible images for a few RT2880 routers based
on Gemtek OEM boards.
Signed-off-by: Claudio Leite
---
tools/firmware-utils/Makefile | 1 +
tools/firmware-utils/src/mkheader_gemtek.c | 211 +
2 files changed, 212 insertions
Signed-off-by: Claudio Leite
---
target/linux/ramips/image/Makefile | 12 +++-
1 file changed, 11 insertions(+), 1 deletion(-)
diff --git a/target/linux/ramips/image/Makefile
b/target/linux/ramips/image/Makefile
index bf9ccc1..26386bf 100644
--- a/target/linux/ramips/image/Makefile
Hi John,
* John Crispin (j...@phrozen.org) wrote:
>
> is there a difference between these 2 patches and the 3/3 that was
> posted earlier ? i already have the 3/3 in my local queue, wanna make
> sure i push the correct patch ...
>
No difference in the code. I just figured it made more sense to
Hi John,
* John Crispin (j...@phrozen.org) wrote:
> if you use ralink SoC please test mac80211 after this update to ensure
> that we do not have a regression.
Looks good here on rt2880.
-Claudio
___
openwrt-devel mailing list
openwrt-devel@lists.openwr
Hi,
I am cleaning up my port for a kirkwood-based router, D-Link DIR-665.
I see there are now some patches for 3.14, and a new 'router'
subtarget. I reworked the port to use the new subtarget. Should I also
rework it to use the newer kernel before I submit it?
I should note it builds (after a min
90 matches
Mail list logo
