I am with Red Sield $850 for $60k. This is also live aboard, think my
deductible is $1000.
Doug Mountjoy Rebecca Leah LF39POYC, WA
Sent from my T-Mobile 4G LTE Device
Original message From: ahycrace ahycrace via CnC-List
Date: 2/3/18 12:50 (GMT-08:00) To:
cnc-list@cnc-lis
Try marinesan.com, they are the local marine sanitation dealer here in Seattle.
Doug Mountjoy Rebecca Leah LF39 POYC, WA
Sent from my T-Mobile 4G LTE Device
Original message From: Bruce Whitmore via CnC-List
Date: 2/5/18 18:47 (GMT-08:00) To: C&C List
Cc: Bruce Whitmore S
The only thing can add (after doing 10 windows) is that the surface need to be
flat and smooth, install and seal out of direct sunlight, minimum 3/16 gap for
sealing, slight bevel on both sides of plexi ( more on tape side) outside just
enough to remove sharp edge, and when sealing push sealant
When I bought Rebecca Leah in June I knew she needed new batteries, 6 group 31
agm's. The PO told me that the batteries were the same as when he bought her in
2003. Knowing I had to pull up the floor boards to easily access them I waited.
Today I pulled out the old ones. They were west marine in
I use a Honda 2000i companion (has 30 amp plug) as a backup power source. At
least until I get my solar up and running. The Honda is quiet and wind disturb
neighbors in anchorage. I would Put the honda on the bow and not hear it in the
cockpit. The 2000 will also power a hot water heater, or 150
Fred, will the link 2000 work on a Prosine 2.5 inverter/charger?
Doug Mountjoy Rebecca Leah LF39 POYC
Sent from my T-Mobile 4G LTE Device
Original message From: Frederick G Street via CnC-List
Date: 2/12/18 12:39 (GMT-08:00) To:
cnc-list@cnc-list.com Cc: Frederick G Street
I installed an Isotherm in Pegasus and was very happy with it for 10 years I
had the boat. Have an old Raritan in Rebecca Leah and not too impressed. From a
live aboard stand point.
Doug Mountjoy Rebecca Leah LF39 POYC, WA.
Original message From: Marek Dziedzic via CnC-List
I haven't heard of these but after a quick search they look like they would
work great.
Doug Mountjoy Rebecca Leah LF39 POYC, WA.
Original message From: Danny Haughey via CnC-List
Date: 3/28/18 05:19 (GMT-08:00) To:
cnc-list@cnc-list.com Cc: Danny Haughey Subject: Stus-
Pegasus my old 38LF had been converted to fresh water cooling. Dont remember
who made the heat exchanger. It used the cam driven vane pump (old raw water
pump) as the recirculating pump. Replaced the impeller once in 10 years of
ownership. Yes access did suck. Never had an issue of that pump fa
Edd, I would go with nothing less than 750 cca, space permitting. The more the
better. The bigger battery will last longer. I am using a group 27 to start my
Yanmar 4jhe44. I took out a 20 year old group 31 that was still working.
Doug Mountjoy Rebecca Leah LF39 Port Orchard YC, WA.
--
Hi Dan,Having towed, and hauled a dinghy all over the Pacific NW. I can say
that davits are the easiest. I use the spin halyard for hoisting on deck for
long passages. For short towing I tow (without the motor) the dinghy pulled up
close with the bow as far up on the mothership transom as poss
Looks good.
Doug Mountjoy Rebecca Leah LF39 POYC, WA.
Original message From: "Dennis C. via CnC-List"
Date: 5/13/18 10:34 (GMT-08:00) To: CnClist
Cc: "Dennis C." Subject: Re:
Stus-List Gold Stripe...
Highly recommend this.
https://www.amazon.com/3M-Scotchcal-Premium-S
In cleaning and lubing my barient winches I found one with the self tailer
tension screws broken. Does any one know where the might be found? I need
minimum 2 screws and 2 springs for a 21ST. I haven't checked to see if they are
the same size on all of my winches.
Sent from my T-Mobile 4G LTE
Matt, were your foils aka torque tube connections secures with rivets or
screws? I need 6 screws for my old harken furler.
Doug Mountjoy Rebecca Leah LF39 POYC, WA.
Original message From: "Matthew L. Wolford via CnC-List"
Date: 5/15/18 10:42 (GMT-08:00) To:
cnc-list@cnc
il pieces, I do have the other various
screws. Does that help?
From: svrebeccaleah via CnC-List
Sent: Tuesday, May 15, 2018 7:40 PM
To: cnc-list@cnc-list.com
Cc: svrebeccaleah
Subject: Re: Stus-List Harken original roller furler
parts
Matt, were your foils aka torque tube connections se
I put one on my LF39 DUE to the center cockpit. It has a line at the mast that
allows me to open and close it. Worth every penny. Mine is from Doyle.
Doug Mountjoy Rebecca Leah LF39 POYC, WA.
Original message From: Edd Schillay via CnC-List
Date: 5/16/18 12:09 (GMT-08:00)
Looking for advice. I need to replace the main reefing lines on my LF39.
Currently I have for #1 reef pt is a 9/16 line and #2 &3 are 1/2 line, not sure
of line type. Want something thinner and lighter. I don't race, just go
cruising. Plan on a lot of offshore in near future. What are your exper
[mailto:cnc-list-boun...@cnc-list.com] On
Behalf Of svrebeccaleah via CnC-List
Sent: Sunday, May 20, 2018 6:53 PM
To: cnc-list@cnc-list.com
Cc: svrebeccaleah
Subject: Stus-List Reading lines Looking for advice. I need to replace the main
reefing lines on my LF39. Currently I have for #1 reef pt is a 9
If bolts are coming loose. I would drill heads for safety wire. Install with
Red lock tight and safety wire so the wire gets tighter when bolts loosen. I
keep a can of 0.032 dua stainless safety wire on board comes in handy for all
sorts of projects.
Doug Mountjoy Rebecca Leah LF39 POYC, WA.
Bill, my old 3qm30 had 2 thermostats. My understanding between the raw water
cooled and fresh water cooled is the opening temperature of the thermostats.
This was from my local Yanmar dealer.
Doug Mountjoy Rebecca Leah LF39 POYC, WA.
Original message From: William Walker via
I am getting ready to pull my mast in July and am wondering how much of the
table I need to dissamble. There is a bottle storage area fwd of the mast with
slide out pieces fwd and aft of the cover. Any thoughts on this?
Sent from my T-Mobile 4G LTE DeviceDoug Mountjoy Port Orchard YC Rebecca Le
@gmail.com Subject: Re: Stus-List LF39
mast removal
Hello Doug,If it is like mine, would suggest you removing the whole table. It
really is not all that hard.
Lloyd Lippe FinesseLF 39
Sent from my iPad
On May 28, 2018, at 4:19 PM, svrebeccaleah via CnC-List
wrote:
I am getting ready to pull
arrangements on the 39, so hopefully we have the same layout and my comments
apply.Hope all works out.
Lloyd Lippe FinesseLF 39
Sent from my iPad
On May 28, 2018, at 5:06 PM, svrebeccaleah via CnC-List
wrote:
Hi Lloyd, Do you have to remove the table top and leaves? That's what it's
lo
50 PM, svrebeccaleah via CnC-List
wrote:
Thanks Lloyd, looks to be what I need to do.I bought this boat a year ago and
am still figuring it out. I would love to compare notes and pick your brain
about the LF39.
Doug Mountjoy Rebecca Leah LF39 Port Orchard YC, WA.
Original message From
Paul, a friend had a stainless one made for his Pretorian (old one was stolen).
I think he used 3/16 or 1/4 inch stainless plate, made a pattern from 1/4
plywood. Came out a work of art.
Doug Mountjoy Rebecca Leah LF39 POYC, WA.
Original message From: Dreuge via CnC-List
D
Does anyone know it the rectangular plate under the mast of the LF39 is
attached to the mast or does the mast just sit on it? Doesn't look like the
plate will clear mast hole in deck.
Sent from my T-Mobile 4G LTE DeviceDoug Mountjoy Port Orchard YC Rebecca Leah
Lf39___
I had a custom matters pad (came with my new matress), and found the custom
sheets didn't work well on my LF38. I used a king fitted sheet folded and
tucked under matters, and a queen flat sheet for top tucked under as far as
possible. Used full size blankets.
Doug Mountjoy Rebecca Leah LF3
I need help. My Ray marine X30 autopilot has crapped out on me. Here is the
historyLast cruise I noticed the heading was way off. I tried swinging the
compass to no avail. Installed a new compass today. Now when I push the auto
button I get "NO COMP". I also cannot access the dealer cal screen.
The water witch works in all types of water. Plus it will not work in oil or
fuel.
Doug Mountjoy Rebecca Leah LF39 Port Orchard YC, WA.
Original message From: Marek Dziedzic via CnC-List
Date: 6/22/18 11:02 (GMT-08:00) To:
cnc-list@cnc-list.com Cc: Marek Dziedzic Subjec
Eric,I just replaced some of my fire extinguishers. There was a year embossed
on the bottom of mine. One was 88, another was 94. As long as the pressure is
in the green, and weight is above minimum on label they are serviceable.(this
is how we check the at the airline I work for). I use a small
I thought the radar some was put there to protect the steaming light. Lol.
Doug Mountjoy Rebecca Leah LF39 POYC, WA.
Original message From: Rod Stright via CnC-List
Date: 6/28/18 16:56 (GMT-08:00) To:
cnc-list@cnc-list.com Cc: Rod Stright Subject: Stus-List
Steaming lig
John,What is the diameter of the holes in your deck? I am replacing all of my
deck fills using the Seadog line on my LF39. 3 fuel, 2 water, and 2 waste.
http://www.sea-dog.com/search?utf8=✓&search_string=351321-1+&x=0&y=0
Doug Mountjoy Rebecca Leah LF39 Port Orchard YC, WA
Original
Mark, When I did my windows I didn't use a primer, just stuck the tape
(VHB4991) straight on the rough epoxy. You might try roughing up thr primer and
wipe with copious amounts of acetone. One thing I learned is put the windows in
when they are cool. The plexiglass expands in sunlight by quite a
Not going to make it this year. Maybe next year.
Doug Mountjoy Rebecca Leah LF39 Port Orchard YC, WA.
Original message From: Lee Youngblood via CnC-List
Date: 7/9/18 09:37 (GMT-08:00) To: CnC-List
Cc: Lee Youngblood
Subject: Re: Stus-List West Coast rendezvous
August
Wrap the 3/4 outlet with good 3m electrical tape til larger hose will just
slide on. then put a hose clamp on.
Doug Mountjoy Rebecca Leah LF39 Port Orchard YC, WA.
Original message From: Eric Frank via CnC-List
Date: 7/11/18 14:16 (GMT-08:00) To:
cnc-list@cnc-list.com Cc:
If I remember my electrical schooling. (It's been a looong time) 455 ÷ 60 × 25
= 189.5 amp hours. Hours × amps = amp hours.
Doug Mountjoy Rebecca Leah LF39 Port Orchard YC, WA.
Original message From: David via CnC-List
Date: 7/12/18 15:13 (GMT-08:00) To: CNC CNC
Cc: David
I am getting to repaint the mast on my 1988 LF39. Does anyone on here have a
clue what paint C&C uses on their spars? The local chandlery suggested Interlux
Brightside, not knowing what is currently on there. Any help would be
appreciated. Thanks in advanceDoug
Sent from my T-Mobile 4G LTE Dev
Glad to see the plug for Port Townsend Rigging. They are currently redoing my
standing rigging, and goose neck. I also added a second sheave for another main
halyard that will also work with a trisail. Dan and Lisa along with the rest of
the staff are very knowledgeable. I am spending a month in
I to feel you pain. I won't say have run aground, but I did not the Ballard
railroad bridge when it was down just before I sold Pegasus my LF38. Not only
do you have to watch but I guess the sky too. ;) After the pain and suffering
and the boat is fixed, you have a great story for the next rende
Dehumidifier. Like this one from Eva-Dry.
https://www.fisheriessupply.com/eva-dry-edv-2500-mid-size-dehumidifier-edv-2500
Getting ready to buy one myself the replace the big clunky one I currently
have.
Doug MountjoySv Rebecca Leah LF39Port Orchard YC
Sent from my T-Mobile 4G LTE Device
--
Don to update your spread sheet. I am in the Port Orchard YC port orchard WA.
Have had Rebecca Leah 1.5 yrs. Been sailing 11 years, and boating 30. Came from
the dark side in 2006.
Doug Mountjoy Sv Rebecca Leah LF39Port Orchard YC
Sent from my T-Mobile 4G LTE Device
null__
Bill,If I remember correctly. On my LF38 I had a 17x12 2 blade and replaced it
with a 17x12 3 blade (over propped). A 17x11 3 blade would be about right. I
had a 3qm30 yanmar.
Doug MountjoySv Rebecca Leah LF39Port Orchard YC
Sent from my T-Mobile 4G LTE Device
null__
Hi Chris, On my girlfriend's boat, she has the same engine. When starting we
set the throttle to about 1/4 to 1/3 then start cranking. Sometimes I'll engage
the compression release to get the engine spinning a little faster (about 10
secs) then release it. Another thing we do is flush the engine
A friend painted his boat with Imeron. Looks great after 7 years. Had to have
is sprayed though. Most yards won't let you spray paint do to the overspray
getting on neighbor boats. Doug
Sent from my T-Mobile 4G LTE Device
null___
Thanks everyone f
New bolts. If their that rusty replace them. Cheap insurance.
Doug Mountjoy Sv Rebecca Leah LH39Port Orchard YC wa.
Original message From: Bev Parslow via CnC-List
Date: 11/3/18 09:20 (GMT-08:00) To:
cnc-list@cnc-list.com Cc: Bev Parslow Subject: Stus-List
cleaning off ru
I second the vote for WIX available at your local NAPA store.
Doug Mountjoy Sv Rebecca Leah LH39Port Orchard YC wa.
null___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to
-List
Date: 11/3/18 10:26 (GMT-08:00) To:
cnc-list@cnc-list.com Cc: Wade Glew Subject: Re: Stus-List
engine oil filters and Car talk
Will Napa be able to tell me which Wix filter will fit my 2GMF Yanmar?WadeOh
Boy C&C 33 MKII
On Sat, Nov 3, 2018, 12:20 svrebeccaleah via CnC-L
I soaked my winch parts in Brakekleen. Came clean after 10 minutes soak time. I
keep a spray can onboard for any oily cleaning I need to do.
Doug Mountjoy Sv Rebecca Leah LH39Port Orchard YC wa.
Original message From: Chris Graham via CnC-List
Date: 11/4/18 05:49 (GMT-08:00)
We have a boat reserved for mid January in the bvi. We'll see. Doug Mountjoy
Sv Rebecca Leah LH39Port Orchard YC wa.
Original message From: David Blair via CnC-List
Date: 11/10/18 14:04 (GMT-08:00) To:
cnc-list@cnc-list.com Cc: David Blair Subject: Stus-List
Charter Caribb
I just put on a Garhauer traveler. Called Guedio at Garhauer and he figured out
the size I needed, plus matched existing mount bolt holes, and how and where
lines would exit. All said and done it was still cheaper than repairing my 25
year old harken traveler. Doug Mountjoy Sv Rebecca Leah LH39P
I use Delo 400 15-40. Doug Mountjoy Sv Rebecca Leah LH39Port Orchard YC wa.
null___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to support the list - use PayPal
to send cont
I want to wish everyone a safe and Happy Thanksgiving. Doug Mountjoy Sv
Rebecca Leah LH39Port Orchard YC wa.___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to support the l
Hi Lee,Can't say much for the water, except that I'm storing some under my
rudder quadrant. As for drill bits. I use cobalt bits. Little more expensive
but last much longer. When drilling metal use slow speed and high pressure.
Cutting oil also helps.Missed you last weekend in Port Orchard. Do
From what I see in the picture, all you will need is a good quality torque
wrench, and a Way to drive the seal into the seal plate. A good gasket scraper,
some acetone or brake kleen to remove all oil residue from gasket surfaces.
Locktight for sealing bolts. Some good quality gasket sealer for
Always better to go with a known quantity. Why replace a good engine for an
annoying oil leak. While the engine is out I would freshen up the fuel injector
pump and injectors, give the heat exchanger a thorough going over, and any
other hard to service items. Doug Mountjoy Sv Rebecca Leah LH39Po
Hi Charlie,At my club, we own buildings, and docks. Most members are
powerboaters(170 boats). We have a committee (1 guy) that handles the racing.
We set aside a portion of the annual budget for the racing. Members get work
party time for helping out with the race committee boat. We also work cl
Here in Port Orchard, West of Seattle, we had an EF-2 tornado touch down 2
miles from the yacht club. Reports from people at the club said winds were
light with heavy rain. I was at the airport working. Just had power flicker. A
few houses destroyed but no reported injuries. Doug Mountjoy Sv Reb
Merry Christmas to all y'all from the wet Pacific Northwest. Doug Mountjoy Sv
Rebecca Leah LH39Port Orchard YC wa.
null___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to su
Ian, I am having a bag made from an old sail, also. The company is Sea Bags.
seabags.com/?utm_source=bing&utm_medium=cpc&utm_campaign=BR_Search_Brand_BING&utm_term=sea
bags&utm_content=MswmwIqC|pcrid|80058229234124|pkw|sea bags|pmt|be|pdv|mDoug
Mountjoy Sv Rebecca Leah LH39Port Orchard YC wa.
--
Hi Tom,This from West Marine. Supply HosesTo carry the gas from the regulator
to the stove or heater, use LPG supply hose of the correct length. Note that
while these hoses are only carrying 0.5 psi, they have a 350 psi working
pressure rating, so they are dramatically stronger than they have to
I have problems backing out of my slip into a very narrow fairway. I have a bow
in Port tie. Backing out I have to pull forward past my slip, back into my slip
using the port prop walk. Then pull out forward. Find it is much easier to just
back in to begin with. Luckily I have a bunch of boat ho
WOW. always amazed at how much a boat can take. Doug Mountjoy Sv Rebecca Leah
LH39Port Orchard YC wa.
null___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to support the list
Only thing I can recommend is run a cable down toe out side corners of steps on
each side of last. This will help prevent lines from getting tangles in the
steps. Doug Mountjoy Sv Rebecca Leah LH39Port Orchard YC wa.
Original message From: "Steven A. Demore via CnC-List"
Date:
My thought on this is, unless they have found a way for plexiglass ( I use this
term loosely) to become one with the fiberglass. It will leak. Doug Mountjoy Sv
Rebecca Leah LH39Port Orchard YC wa.
Original message From: David Knecht via CnC-List
Date: 2/16/19 07:43 (GMT-08:00
I am upgrading my electronics and need to get rid of my old stuff. Furuno 1720
radar display and dome no cableGarmin 4208 plotterGarmin 3205 plotterWatchmate
ais display, needs an ais reciever.Garmin network hubGarmin GSD 22 Datamarine
link 5000 wind, speed,depthDatamarine 5000.Datamarine wind t
Inch wide tape would be more than strong enough. IMHO.Doug Mountjoy Sv Rebecca
Leah LH39Port Orchard YC wa.
Original message From: Bruce Whitmore via CnC-List
Date: 3/1/19 10:46 (GMT-08:00) To: CnClist
Cc: Bruce Whitmore Subject:
Stus-List Fixed port ahead of slider, C&C 3
Hi Patrick,I installed a belowdecks autopilot on Pegasus. Contact Kyle as he
now has Pegasus there in Shilshole. Maybe he'll let you look at the way I
installed it. Good luckDoug. Doug Mountjoy Sv Rebecca Leah LH39Port Orchard YC
wa.
Original message From: Patrick Davin via CnC-
Hi Fred, I can't help on length, but for installing new cable. Before pulling
old cable out tie a 1/8 inch line to the cable to use for pulling new cable
back in place. Once cable is out it is a simple chore to measure. I use this
method for pulling wires, cables or what ever. Doug Mountjoy Sv R
When I had my LF38 with a 3QM30. I did try a stop cable, but it was not a cable
that locked. Pushing down on the throttle would override the stop cable.The way
this engine shuts down is by closing the throttle beyond the idle position.
From idle to shutdown is only about 1/2 inch movement on a d
I hauled Rebecca Leah this past weekend to install new thru hull transducers.
Been up grading my electronics. I noticed that my prop has some serious pitting
and loose blades. I currently have a feathering prop. My plan is to do some
extensive blue water cruising in the near future. So my questi
I tighten mine until there is very little slop in the wheel. I don't think
there needs to be much tension. Doug Mountjoy Sv Rebecca Leah LF39Port Orchard
YC wa.
null___
Thanks everyone for supporting this list with your contributions. Each and
every
Shawn, I replaced my 30 yr old rigging last summer only because I plan on doing
extended off shore cruising. Had I not been planning this I would not have done
so, as the cost was that of a new car. I did have to replace 1 roller furler,
goose neck, and did a couple of up grades. If your worried
I also had a flexible holding tank that failed. Go with a hard plastic one.
Doug Mountjoy Sv Rebecca Leah LF39253-208-1412Port Orchard YC wa.
Original message From: Shawn Wright via CnC-List
Date: 4/23/19 08:37 (GMT-08:00) To:
cnc-list@cnc-list.com Cc: Shawn Wright Subject:
My Landfall 39 has crossed the Pacific a couple of time with previous owners.
Although not a light air boat (compared to the LF38), It feels solid under full
sail in 25kt winds. Doug Mountjoy Sv Rebecca Leah LF39 1988253-208-1412Port
Orchard YC wa.
Original message From: Jeff He
Both of the landfall models (38 & 39) have not had this bar. The 38 was hull #4
so maybe this rod thing is post 1979, or it wasn't installed on the landfall
models. Doug Mountjoy Sv Rebecca Leah C & C LF39253-208-1412Port Orchard YC wa.
Original message From: Tom Buscaglia via Cn
Andy, I have the same philosophy. I too spend all my money on Rebecca Leah.
Sometimes I'll sneak a few dollars to spend on my hot rod truck or motorcycle.
BUT I don't let her know. Last summer she got new rigging, and she just got
new electronics. I think I might need some intervention. LOL.
Is the current outhaul line still there? Can you attach a new line to old and
pull it thru?I use whipping twine to sew old and new lines end to end then
gently pull in new line. Doug Mountjoy Sv Rebecca Leah LF39253-208-1412Port
Orchard YC wa.
Original message From: Luke Wolbrin
FWI. Back in the day of rigging airplanes. I would use heat shrink (non
adhesive type) to connect the old and new cables. Pull out old cable gently and
new will be routed correctly. DougSent from my T-Mobile 4G LTE Device
Thanks to all of the subscribers that contributed to the list to help with
A true Bruce is better than a Danforth. I have an Excell based on these
videos.They are long videos but I think very informative.
https://youtu.be/smgWTtFuk3Uhttps://youtu.be/ua21k2abK1QFWIW Sent from my
T-Mobile 4G LTE Device
Original message From: "Della Barba, Joe via CnC-Li
I went with the excel also based on Panopes observations. I have the 45lb
excel backed up by 300ft 5/16 G4 chain. A friend and I were rated on his 35lb
Spade anchor and 100 ft of chain no issues. His boat is a Pretorian 35, 15k lbs
, mine is a landfall 39 24k lbs. The 2 of us have been on my an
Counter sink top and bottom, tape over bottom of hole. Then fill with thickened
epoxy. I go for about the consistency of ketchup. Without the counter sink. It
will crack over time. DougSent from my T-Mobile 4G LTE Device
Original message From: Wade Glew via CnC-List
Date: 8/27/
Glad to hear all are ok. Out here on the west coast I would like a little bit
of your wind. Sailind down to San Diego in 2-10kts of wind makes for a long
motor. Heading out the Straits of Juan de Fuca we beat head on into 19kts of
wind. Turned the corner at Cape Flattery today, we were able to s
Is the prop clean? I may also be the fuel filters. It sounds like low fuel
flow. Put in new filters, and bleed the system. DougSent from my T-Mobile 4G
LTE Device
Original message From: Dave via CnC-List
Date: 9/7/21 18:17 (GMT-08:00) To:
cnc-list@cnc-list.com Cc: syerd...@g
Hi JoeI would love one. DougSent from my T-Mobile 4G LTE Device
Original message From: Ourtime via CnC-List
Date: 2/15/21 13:22 (GMT-05:00) To:
cnc-list@cnc-list.com Cc: Ourtime Subject: Stus-List Re:
Anyone need a Racor vacuum gauge
If it's still available, I'd like to giv
I would go with the largest 30 to 35 hp. You may not always need the extra
power, but it is a lifesaver when you do. Sent from my T-Mobile 4G LTE Device
Original message From: Jeremy Ralph via CnC-List
Date: 2/16/21 14:08 (GMT-05:00) To:
cnc-list@cnc-list.com Cc: Jeremy Ralph
Hi Kevin,I also have the LF 39. The chain plates are 3/8th stainless bar stock
through bolted to frame members glassed to the hull, they are about 3 feet
long. I pulled my mast 3 years ago, replaced the rod rigging, and basically
rebuilt the mast. Goose neck was trashed. Major reason for yarding
86 matches
Mail list logo
