Kevin:
I intended using suction cups to hold my new windows in place, however,
before I actually did the job, I experimented with the suction cups on
the new windows and found they did not hold on for very long. I used
Sika 295 |||UV as the adhesive and therefore left the 'paper' on
t
Hi All,
Last year B&G had a promo/rebate on their wind/speed/depth package where
they offered a free display with the purchase of the kit. That was a good
deal and I would have taken advantage of it then but other priorities won
out.
Right now, it looks like B&G is only offering a $100 rebate on
Hi,
I need the help and support of the list to find a solution for a friend of mine
that is stock with his boat and family in Georgetown, Exumas, Bahamas. His 1
inch shaft (the boat) simply broke in two pieces after catching a line at 2600
rpr. Probably a manufacturing defect. He needs repla
Bruno
Cutlass bearings vary in length and outside diameter.
Joel
On Wednesday, February 18, 2015, Bruno Lachance via CnC-List <
cnc-list@cnc-list.com> wrote:
>
> Hi,
>
> I need the help and support of the list to find a solution for a friend of
> mine that is stock with his boat and family in G
Just downloaded the B&G rebate PDF from Defender, and the rebate for the Triton
Speed/Depth/Wind package is $150US and an additional Triton give $50US more.
Defender has a 2 Triton + Speed/Depth/Wind package at $1700. If I compare with
BLYacht.com pricing for the equivalent (Triton S/D/W pack + 1
Bruno,
A number of things to take into consideration here.
a) The keyway will need to be cut into the shaft before shipping.
Accurate measurements are crucial.
b) The Drive Saver will be a good addition, but it will also affect the
finished shaft length. I had to trim several in
Start with Sailorman in Fort Lauderdale. Www.sailorman.com to get their phoner.
It's a huge, old-fashioned chandlery with a great staff. If they don't have it,
they will connect you with the people who do.
Jack Brennan
Former C@C 25
Shanachie, 1974 Bristol 30
Sent from my Samsung Galaxy Tab®
Check into Raymarine they have a rebate program right now. I was going with
Garmin, but now think I will go with Raymarine
On Wed, Feb 18, 2015 at 9:42 AM, Stevan Plavsa via CnC-List <
cnc-list@cnc-list.com> wrote:
> Hi All,
>
> Last year B&G had a promo/rebate on their wind/speed/depth package w
if you keep the paper on the acrylic, the suction will be lost quite fast.
Leslie.
On Tue, 2/17/15, Kevin Driscoll via CnC-List wrote:
Subject: Re: Stus-List Portlight Replacement with VHB Tape & Dow 795
To: "Dr. Mark Bodnar" , cnc-list@cnc-list.c
Thanks all. I guess my mistake was looking at Canadian sites... and not
reading the rebate form carefully!
I've purchased from Defender in the past and it's usually worked out but
with the exchange rate being what it is at the moment I didn't really
consider it. Pierre, I didn't know about blyacht.
Three other Canadian online vendors for your consideration:
http://shop.yachtshop.ca/
http://www.marineoutfitters.ca/
http://www.hollandmarine.com/
I've done business with all of then at one time or another, all with good
results.
Ken H.
On 18 February 2015 at 15:44, Stevan Plavsa via CnC-Lis
The B&G Wind / Depth / Speed has a $150 (US, so the form says) rebate until end
of March. The package is $1600 (CAN) at Westmarine. I've seen it at US online
retailers for as low as $1230 (US) ... but then you've got shipping and
probably duty to contend with.
Marineoutfitters has the Plastimo
Bruno,
Never did business with these folks, but I had bookmarked their site:
http://www.deepblueyachtsupply.com/
Joel
On Wed, Feb 18, 2015 at 10:57 AM, jackbrennan
wrote:
> Start with Sailorman in Fort Lauderdale. Www.sailorman.com to get their
> phoner. It's a huge, old-fashioned chandlery w
Holland Marine I know, they're local. The other two I don't, so thanks!
Good idea about the West Marine closure.
Steve
Suhana, C&C 32
Toronto
On Wed, Feb 18, 2015 at 3:33 PM, prf680 via CnC-List
wrote:
> The B&G Wind / Depth / Speed has a $150 (US, so the form says) rebate
> until end of March
Bruno,
You are a very good friend.
What make and model boat does your friend have? 1" Shaft". Length? Keyway
dimensions? Taper for the prop? Cutless bearing OD and length?
There is a slim chance someone on this list has replaced theirs so your friend
may have to haul the boat, remove the sha
Chuck S via CnC-List wrote:
Bruno,
You are a very good friend.
What make and model boat does your friend have? 1" Shaft". Length?
Keyway dimensions? Taper for the prop? Cutless bearing OD and length?
There is a slim chance someone on this list has replaced theirs so
your friend may hav
I have a 1” shaft, 44” long.
Propeller shaft. About 2 ½” long keyway, I think they are all ¼” key
Regards,
Bill Coleman
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Chuck S via
CnC-List
Sent: Wednesday, February 18, 2015 5:26 PM
To: Bruno Lachance; CNC boat owne
The guy who owns Holland Marine in Toronto has (or at least had) a CS36 but
I don't know if it is a Merlin.
He also got a lot of CS left over parts, after CS closed down.
It is possible that he got some of their documentation as well, I do know
that he got a LOT of stuff.
If memory serves corre
Toronto WM is closed Oakville not yet.
See what Mike at the Dock Shoppe (Genco location just off Queens Quay) or Fogh
Marine in Port Credit have also.
Sent from my iPad
On Feb 18, 2015, at 5:12 PM, Stevan Plavsa via CnC-List
mailto:cnc-list@cnc-list.com>> wrote:
Holland Marine I know, th
I bought a shaft seal and a cutlass bearing from them, you can count me
as a happy customer.
Graham Collins
Secret Plans
C&C 35-III #11
On 2015-02-18 5:40 PM, Joel Aronson via CnC-List wrote:
Bruno,
Never did business with these folks, but I had bookmarked their site:
http://www.deepblueyach
Hello listers,
Thanks for the support, i received some good tips and it helps to limit
potential errors.
here is the update on the situation. the cutlass and drive saver plate are
already on order. the most complicated part is to find or calculate the right
lenght of the prop shaft. the actua
I'm a member on the CS owners association group - a request for shaft
info was already posted on that list yesterday.
There is no cure for birth and death save to enjoy the interval.
- George Santayana
On 2015-02-18 6:44 PM, Bill Connon via CnC-List wrote:
Chuck S via CnC-List wrote:
Bru
mark, in fact i found a question in the wiki section not the discussion list,
i'm not a member. If you can Check the list and report please, it would be very
appreciated.
I will ask my friend if its him, his name is Fred.
Thanks again for the reply.
Envoyé de mon iPad
> Le 2015-02-18 à 22:04
Hi Bruno.
If this has been mentioned then I missed it.
Please tell your friend (Fred) that a very
important step in a successful prop shaft install
is to true the flange face with it mounted to the
shaft. Even with a brand new custom shaft & brand
new coupling half, it is good to true the fac
24 matches
Mail list logo
