I have a usb microphone on device 0 and a via8235 on device 1. How can I configure
them so I can play and record on the appropriate devices? I can always say, "aplay -D
hw:1,0 file.wav", but that doesn't work for xmms or xine.
pgp0.pgp
Description: PGP signature
On Fri, 3 Oct 2003, Free Ekanayaka wrote:
> I'd like to know how should I write the asoundrc in order to
> record the audio stream that comes from an OSS application
> writing in /dev/dsp to a file or equivalently to create a virtual
> capture device from which an application can record. To be cle
Hi,
I have successfully installed the alsa-driver-0.9.7 with my i8x0 (AC' 97) onboard
soundcard. However, I have 4 speakers (actually 5 if you include the subwoofer) but I
only get sound from the (two) front speakers.
Is there a way to get sound from the two rear speakers as well?
Regards,
Met
Hi,
İ have an asus a7v8x-x mobo and the nasty via8235 southbridge chip on
it. i am using ALSA 0.9.7a and Linux 2.4.22 with low latency patch
(Linux Fron Scratch 4.1 )...
it is not working stable i have some noise problems especially while
running xmms. When modprobing i see the the fameous m
Hi,
When I try to play sound with a soundplayer for KDE I can only get
analog sound. When I use the following syntax for aplay I can play
sound without any problem through the digital out:
aplay -D plug:iec958 /sample.wav
I tried to apply the same the the settings in the Control Center
(Sound & M
I had a thought that ns558 might assume an address of 0x200, but I can't
find a way to tell it 0x201.
FYI - looking at the driver source, it says:
static int ns558_isa_portlist[] = { 0x200, 0x201, 0x202, 0x203, 0x204,
0x205, 0x207, 0x209, 0x20b, 0x20c,
Hello all,
I'm having some troubles getting my joystick (MS Sidewinder 3D pro) to
work under ALSA. Info:
- Kernel is 2.4.22
- Alsa-Driver is 0.9.7
- Soundcard is Hoontech Soundtrack i-Phone Digital XG (YMF754)
- Joystick is MS Sidewinder 3D pro
- Soundcard is known good (just tried it in a Windo
Hi,
On Sat, Oct 04, 2003 at 12:14:32PM -0400, [EMAIL PROTECTED] wrote:
> > I have successfully installed the alsa-driver-0.9.7 with my i8x0 (AC' 97)
> > onboard soundcard. However, I have 4 speakers (actually 5 if you include
> > the subwoofer) but I only get sound from the (two) front speakers.
Hi,
I'm trying to get my RME hdsp-pci+multiface working using the latest
alsa 0.9.7a, and kernel 2.4.22 (with lowlat, preempt and 1000Hz patches).
And this is the output I get from hdsploader:
] hdsploader - firmware loader for RME Hammerfall DSP cards
] Looking for HDSP + Multiface or Digiface c
>I'd be nice if the UI for
>them could be simplifed a little so those of us who don't know how to
>program sound cards could configure things like 5 channel output :).
QAmix is pretty cool. I find it less cryptic and easier to use
than alsamixer.
--
Thank you for explainng to me.
I am very satisified with the answer.
I found setting Master volume to 100 and PCM volume to 75 is what I want.
But setting Master volume to 75 and PCM volume to 100 will cause sound
clicking.
FYI
- Original Message -
From: "p z " <[EMAIL PROTECTED]>
To:
I have a Dell Latitude CPi with a CS4237B chipset. I have my
modules.conf file set up with the following:
alias char-major-116 snd
alias snd-card-0 snd-cs4236
alias char-major-14 soundcore
alias sound-slot-0 snd-card-0
alias sound-service-0-0 snd-mixer-oss
alias sound-service-0-1 snd-seq-oss
ali
Hi there.
I've recently reinstalled my system.
I installed kernel 2.4.22 with sound card support compiled as a module (and
no other drivers under sound compiled)
I installed the ALSA driver, library and utils package version 0.9.6.
The soundcard is an ISA SB16 PnP.
The system is a K6-2 300 on a C
Takashi,
"Wave Surround" is currently maxed out, and I'm still only getting
audio from the front speakers. In fact, looking at alsamixer, I'm
noticing that there's no option for "3D Control - Switch," "3D Control
Sigmatel - Depth," or "3D Control Sigmatel - Rear Depth". All three
option
I'm using ALSA 0.9.6 with VLC (on RedHat 9) to play back VideoCDs.
Everything works fine but audio is not perfect, it seems losing some
bits every few seconds (i.e. you don't ear anything for a very small
fraction of time).
Using 'vlc -vvv dvd:/dev/cdrom' I see that when the audio disappear
there i
Does anyone know how I can use the SPDIF-Port on the Meastro 3i in my
Dell Inspiron 8000 Laptop?
I could not get it to output anything using quite a lot of experimenting
and research with mplayer, xine and ac3dec.
Marcus
---
This sf.net emai
Does anyone know how I can use the SPDIF-Port on the Meastro 3i in my
Dell Inspiron 8000 Laptop?
I could not get it to output anything using quite a lot of experimenting
and research with mplayer, xine and ac3dec.
Marcus
---
This sf.net emai
I appear to have missed something during Alsa installation and am unable to
get any sound out of my system's speakers. Here is what I get from the
following queries:
[EMAIL PROTECTED] root]# lspci -vv
00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge
(rev 04)
Co
replying to myself , the sound is ALSO distorted now even from the
analog outout (it worked well with 0.9.6) . It also seems to take a few
seconds (around 10) of fine playback and then the distortion starts.
Best regards ,
--
==
Is there really noone who knows how to activate the rear speakers?
On Thursday 02 October 2003 07:05, [EMAIL PROTECTED] wrote:
> Hi,
>
> I have successfully installed the alsa-driver-0.9.7 with my i8x0 (AC' 97)
> onboard soundcard. However, I have 4 speakers (actually 5 if you include
> the subwoo
20 matches
Mail list logo
