Re: Intel Pro 100 doesn't work
Yep, loading pcmcia first. Can get the pcmcia modem to work fine, but not the card. I think I'm going to try potato(e) with the later version of cardmgr and see if that does the trick. The card is listed as supported on the pcmcia web site, but of course I didn't check versions. (doh!) thanks. -- _ David J. Kuntz [EMAIL PROTECTED]
Xircom Ethernet/Modem problem
I have a Dell Lattitude CP with a Xircom 33k6 Eth/modem combo. I installed slink with no problems. The card is recognised and configured properly and the ethernet device works. Problem is the modem. I can see no errors in the syslog file (attached), but sending ATZ to the modem has no effect. I read some HOWTO's and README files, but have not found the problem or the solution. Does this ring a bell to you, or have you got any suggestions where to look? please tell me! Greating, Ben Mesman. --- Part of syslog --- Nov 5 09:15:07 nl1019 cardmgr[103]: starting, version is 3.0.5 Nov 5 09:15:07 nl1019 cardmgr[103]: watching 2 sockets Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x1000-0x17ff: excluding nothing: probe failed. Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x210-0x217 0x220-0x22f 0x290-0x297 0x378-0x37f 0x388-0x38f 0x4d0-0x4d7 Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x0a00-0x0aff: clean. Nov 5 09:15:07 nl1019 kerneld: started, pid=110, qid=0 Nov 5 09:15:07 nl1019 cardmgr[103]: initializing socket 0 Nov 5 09:15:07 nl1019 kernel: cs: memory probe 0xa000-0xa0ff: clean. Nov 5 09:15:07 nl1019 cardmgr[103]: socket 0: Xircom CEM33 Ethernet/Modem Nov 5 09:15:07 nl1019 cardmgr[103]: executing: 'insmod /lib/modules/2.0.36/pcmcia/xirc2ps_cs.o' Nov 5 09:15:07 nl1019 kernel: xirc2ps_cs.c 1.29 1998/04/27 19:20:19 (dd9jn+kvh) Nov 5 09:15:07 nl1019 cardmgr[103]: executing: 'insmod /lib/modules/2.0.36/pcmcia/serial_cs.o' Nov 5 09:15:07 nl1019 kernel: eth0: Xircom: port 0x2d0, irq 3, hwaddr 00:80:C7:74:30:DC Nov 5 09:15:07 nl1019 kernel: tty03 at 0x02e8 (irq = 3) is a 16450 Nov 5 09:15:07 nl1019 cardmgr[103]: executing: './network start eth0' Nov 5 09:15:09 nl1019 kernel: eth0: switching to 10BaseT port Nov 5 09:15:09 nl1019 kernel: eth0: media 10Base2, silicon revision 1 Nov 5 09:15:10 nl1019 kernel: eth0: media 10Base2, silicon revision 1 Nov 5 09:15:10 nl1019 cardmgr[103]: executing: './serial start ttyS3' Nov 5 09:20:50 nl1019 kernel: registered device ppp0 Nov 5 09:20:50 nl1019 pppd[192]: pppd 2.3.5 started by root, uid 0 Nov 5 09:20:51 nl1019 chat[193]: abort on (BUSY) Nov 5 09:20:51 nl1019 chat[193]: abort on (NO CARRIER) Nov 5 09:20:51 nl1019 chat[193]: abort on (VOICE) Nov 5 09:20:51 nl1019 chat[193]: abort on (NO DIALTONE) Nov 5 09:20:51 nl1019 chat[193]: abort on (NO ANSWER) Nov 5 09:20:51 nl1019 chat[193]: send (ATZ^M) Nov 5 09:20:51 nl1019 chat[193]: expect (OK) Nov 5 09:21:36 nl1019 chat[193]: alarm Nov 5 09:21:36 nl1019 chat[193]: Failed Nov 5 09:21:36 nl1019 pppd[192]: Connect script failed Nov 5 09:21:37 nl1019 pppd[192]: Exit. ---End---
Re: Debian on Sony 505TX
>Could you please send me a copy of my last two messages so I can post >them to the list. Maybe somebody else will be able to add something >useful to my comments. OK, no problem. I will do something better: I will cc the messages to the list, with my comments, to save you the time to post them yourself. >BTW, how's it going? Did you get X running yet? Yes, finally!! After so long time I finally saw X on my screen! Still X doesn't look very nice. Fonts too big to have a program on the screen, and low resolution. I guess to configure this must be easy compare with the installation. Where in X you can see and change the settings of the display? Thanks again Dada
Re: Debian on Sony 505TX
After much struggle I finally got X running. Wow it feels great! Still the display is not so good, but at least X is starting now. Thanks to Mitch, Sean, Greg and the others for your guidance. At 12:03 AM 11/6/1999 -0500, Mitch Lewandowski wrote: >The good news is that you have the hardest part overwith. ;-) Good news indeed!! I was starting to get a bit worry >Your next step would be to search for a window manager on the system. if >you do not find anything, of course you can always apt-get one >(enlightenment is my personal fav - apt-get install enlightenment >enlightenment conf). Then it would be wise of you to make a .xinitrc file >in your home dir. The only window manager I have is Debian. Very simple and with huge fonts. What is a .xinitrc file? And , how to make one in my home directory? Thanks Dada
Re: Debian on Sony 505TX
At 04:10 PM 11/5/1999 -0800, you wrote: >Which version of Debian are you installing? Debian 2.1 "Slink" has an old >version of XFree86 that I don't think will work with the Vaio. > >You can get a new version of XF86_SVGA from "http://www.netgod.net/x"; >using either apt-get or by downloading it manually and using >"dpkg -i packagename". I have the Debian 2.1 "Slink" CD's. And I saw that I had XF86_VGA and not SVGA. So I got the SVGA from netgod and then X worked. Thanks Dada
Re: Debian on Sony 505TX
At 09:15 PM 11/5/1999 -0800, you wrote: >You want xserver-svga_3.3.3.1-2_i386.deb > >It would also be a good idea to get the latest versions of these >X .debs too: > > xserver-common > xfree86-common > xf86setup > xbase-clients > xlib6 > xlib6g > xfs > xfonts-scalable > xfonts-base > xfonts-75dpi > xfonts-100dpi > >There's an XF86Config file at http://bob.usuhs.mil/sony-pcg-505tx.html >that will probably do the job for you. The Debian 2.1 CD's I have, contain the older version of all those files. That is 3.3.2.3a-11 Also in the debian.org web pages I found only the old versions. But the http://www.netgod.net/x pages you pointed have all the latest versions of those files. That is 3.3.3.1-2 (Thanks God for netgod!) Dada
Hibernation
I have an IBM 365XD running 2.2.1 kernel. I have recompiled the kernel to support APM. I have been reading several websites that state that in order to use the hibernation feature on my laptop I have to create a dos partition on which a hibernation file can be saved. Unfortunately, I have all of my hard drive space used for my linux and swap partitions. Is there a simple way to add a new partition so I can use the hibernation feature on my laptop? Or does anyone know of another way which can be used to invoke hibernation using my current setup? (ie without having to repartition my HD). I hope that someone can offer some insight. David
Re: Hibernation
Hi! Maybe you want to look at this: http://falcon.sch.bme.hu/~seasons/linux/swsusp.html It's a patch to allow hibernation to your swap. I didn't test it yet but I'm at it. Hth Tobias --- Tobias Bachmor Department of Computer Science Concordia University at Montreal/Canada ---
Re: Xircom Ethernet/Modem problem
I have the same card, upgrade your kernel to >= 2.2.13. It fixed my problem. On Mon, 8 Nov 1999, Mesman, Ben wrote: > I have a Dell Lattitude CP with a Xircom 33k6 Eth/modem combo. I installed > slink with no problems. The card is recognised and configured properly and > the ethernet device works. > Problem is the modem. I can see no errors in the syslog file (attached), but > sending ATZ to the modem has no effect. > I read some HOWTO's and README files, but have not found the problem or the > solution. > > Does this ring a bell to you, or have you got any suggestions where to look? > please tell me! > > Greating, > Ben Mesman. > > --- Part of syslog --- > Nov 5 09:15:07 nl1019 cardmgr[103]: starting, version is 3.0.5 > Nov 5 09:15:07 nl1019 cardmgr[103]: watching 2 sockets > Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x1000-0x17ff: excluding > nothing: probe failed. > Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x0100-0x04ff: excluding > 0x210-0x217 0x220-0x22f 0x290-0x297 0x378-0x37f 0x388-0x38f 0x4d0-0x4d7 > Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x0a00-0x0aff: clean. > Nov 5 09:15:07 nl1019 kerneld: started, pid=110, qid=0 > Nov 5 09:15:07 nl1019 cardmgr[103]: initializing socket 0 > Nov 5 09:15:07 nl1019 kernel: cs: memory probe 0xa000-0xa0ff: > clean. > Nov 5 09:15:07 nl1019 cardmgr[103]: socket 0: Xircom CEM33 Ethernet/Modem > Nov 5 09:15:07 nl1019 cardmgr[103]: executing: 'insmod > /lib/modules/2.0.36/pcmcia/xirc2ps_cs.o' > Nov 5 09:15:07 nl1019 kernel: xirc2ps_cs.c 1.29 1998/04/27 19:20:19 > (dd9jn+kvh) > Nov 5 09:15:07 nl1019 cardmgr[103]: executing: 'insmod > /lib/modules/2.0.36/pcmcia/serial_cs.o' > Nov 5 09:15:07 nl1019 kernel: eth0: Xircom: port 0x2d0, irq 3, hwaddr > 00:80:C7:74:30:DC > Nov 5 09:15:07 nl1019 kernel: tty03 at 0x02e8 (irq = 3) is a 16450 > Nov 5 09:15:07 nl1019 cardmgr[103]: executing: './network start eth0' > Nov 5 09:15:09 nl1019 kernel: eth0: switching to 10BaseT port > Nov 5 09:15:09 nl1019 kernel: eth0: media 10Base2, silicon revision 1 > Nov 5 09:15:10 nl1019 kernel: eth0: media 10Base2, silicon revision 1 > Nov 5 09:15:10 nl1019 cardmgr[103]: executing: './serial start ttyS3' > Nov 5 09:20:50 nl1019 kernel: registered device ppp0 > Nov 5 09:20:50 nl1019 pppd[192]: pppd 2.3.5 started by root, uid 0 > Nov 5 09:20:51 nl1019 chat[193]: abort on (BUSY) > Nov 5 09:20:51 nl1019 chat[193]: abort on (NO CARRIER) > Nov 5 09:20:51 nl1019 chat[193]: abort on (VOICE) > Nov 5 09:20:51 nl1019 chat[193]: abort on (NO DIALTONE) > Nov 5 09:20:51 nl1019 chat[193]: abort on (NO ANSWER) > Nov 5 09:20:51 nl1019 chat[193]: send (ATZ^M) > Nov 5 09:20:51 nl1019 chat[193]: expect (OK) > Nov 5 09:21:36 nl1019 chat[193]: alarm > Nov 5 09:21:36 nl1019 chat[193]: Failed > Nov 5 09:21:36 nl1019 pppd[192]: Connect script failed > Nov 5 09:21:37 nl1019 pppd[192]: Exit. > ---End--- > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] > >
Re: Xircom Ethernet/Modem problem
You may try this adress: http://hyper.stanford.edu/HyperNews/get/pcmcia/xircom.html It's a web page/e-mail list dedicated to Xircom drivers development. Nuno Faria "Mesman, Ben" wrote: > > I have a Dell Lattitude CP with a Xircom 33k6 Eth/modem combo. I installed > slink with no problems. The card is recognised and configured properly and > the ethernet device works. > Problem is the modem. I can see no errors in the syslog file (attached), but > sending ATZ to the modem has no effect. > I read some HOWTO's and README files, but have not found the problem or the > solution. > > Does this ring a bell to you, or have you got any suggestions where to look? > please tell me! > > Greating, > Ben Mesman. >
Re: Intel Pro 100 doesn't work
Yep, loading pcmcia first. Can get the pcmcia modem to work fine, but not the card. I think I'm going to try potato(e) with the later version of cardmgr and see if that does the trick. The card is listed as supported on the pcmcia web site, but of course I didn't check versions. (doh!) thanks. -- _ David J. Kuntz [EMAIL PROTECTED]
Xircom Ethernet/Modem problem
I have a Dell Lattitude CP with a Xircom 33k6 Eth/modem combo. I installed slink with no problems. The card is recognised and configured properly and the ethernet device works. Problem is the modem. I can see no errors in the syslog file (attached), but sending ATZ to the modem has no effect. I read some HOWTO's and README files, but have not found the problem or the solution. Does this ring a bell to you, or have you got any suggestions where to look? please tell me! Greating, Ben Mesman. --- Part of syslog --- Nov 5 09:15:07 nl1019 cardmgr[103]: starting, version is 3.0.5 Nov 5 09:15:07 nl1019 cardmgr[103]: watching 2 sockets Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x1000-0x17ff: excluding nothing: probe failed. Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x210-0x217 0x220-0x22f 0x290-0x297 0x378-0x37f 0x388-0x38f 0x4d0-0x4d7 Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x0a00-0x0aff: clean. Nov 5 09:15:07 nl1019 kerneld: started, pid=110, qid=0 Nov 5 09:15:07 nl1019 cardmgr[103]: initializing socket 0 Nov 5 09:15:07 nl1019 kernel: cs: memory probe 0xa000-0xa0ff: clean. Nov 5 09:15:07 nl1019 cardmgr[103]: socket 0: Xircom CEM33 Ethernet/Modem Nov 5 09:15:07 nl1019 cardmgr[103]: executing: 'insmod /lib/modules/2.0.36/pcmcia/xirc2ps_cs.o' Nov 5 09:15:07 nl1019 kernel: xirc2ps_cs.c 1.29 1998/04/27 19:20:19 (dd9jn+kvh) Nov 5 09:15:07 nl1019 cardmgr[103]: executing: 'insmod /lib/modules/2.0.36/pcmcia/serial_cs.o' Nov 5 09:15:07 nl1019 kernel: eth0: Xircom: port 0x2d0, irq 3, hwaddr 00:80:C7:74:30:DC Nov 5 09:15:07 nl1019 kernel: tty03 at 0x02e8 (irq = 3) is a 16450 Nov 5 09:15:07 nl1019 cardmgr[103]: executing: './network start eth0' Nov 5 09:15:09 nl1019 kernel: eth0: switching to 10BaseT port Nov 5 09:15:09 nl1019 kernel: eth0: media 10Base2, silicon revision 1 Nov 5 09:15:10 nl1019 kernel: eth0: media 10Base2, silicon revision 1 Nov 5 09:15:10 nl1019 cardmgr[103]: executing: './serial start ttyS3' Nov 5 09:20:50 nl1019 kernel: registered device ppp0 Nov 5 09:20:50 nl1019 pppd[192]: pppd 2.3.5 started by root, uid 0 Nov 5 09:20:51 nl1019 chat[193]: abort on (BUSY) Nov 5 09:20:51 nl1019 chat[193]: abort on (NO CARRIER) Nov 5 09:20:51 nl1019 chat[193]: abort on (VOICE) Nov 5 09:20:51 nl1019 chat[193]: abort on (NO DIALTONE) Nov 5 09:20:51 nl1019 chat[193]: abort on (NO ANSWER) Nov 5 09:20:51 nl1019 chat[193]: send (ATZ^M) Nov 5 09:20:51 nl1019 chat[193]: expect (OK) Nov 5 09:21:36 nl1019 chat[193]: alarm Nov 5 09:21:36 nl1019 chat[193]: Failed Nov 5 09:21:36 nl1019 pppd[192]: Connect script failed Nov 5 09:21:37 nl1019 pppd[192]: Exit. ---End---
Re: Debian on Sony 505TX
>Could you please send me a copy of my last two messages so I can post >them to the list. Maybe somebody else will be able to add something >useful to my comments. OK, no problem. I will do something better: I will cc the messages to the list, with my comments, to save you the time to post them yourself. >BTW, how's it going? Did you get X running yet? Yes, finally!! After so long time I finally saw X on my screen! Still X doesn't look very nice. Fonts too big to have a program on the screen, and low resolution. I guess to configure this must be easy compare with the installation. Where in X you can see and change the settings of the display? Thanks again Dada
Re: Debian on Sony 505TX
After much struggle I finally got X running. Wow it feels great! Still the display is not so good, but at least X is starting now. Thanks to Mitch, Sean, Greg and the others for your guidance. At 12:03 AM 11/6/1999 -0500, Mitch Lewandowski wrote: >The good news is that you have the hardest part overwith. ;-) Good news indeed!! I was starting to get a bit worry >Your next step would be to search for a window manager on the system. if >you do not find anything, of course you can always apt-get one >(enlightenment is my personal fav - apt-get install enlightenment >enlightenment conf). Then it would be wise of you to make a .xinitrc file >in your home dir. The only window manager I have is Debian. Very simple and with huge fonts. What is a .xinitrc file? And , how to make one in my home directory? Thanks Dada
Re: Debian on Sony 505TX
At 04:10 PM 11/5/1999 -0800, you wrote: >Which version of Debian are you installing? Debian 2.1 "Slink" has an old >version of XFree86 that I don't think will work with the Vaio. > >You can get a new version of XF86_SVGA from "http://www.netgod.net/x"; >using either apt-get or by downloading it manually and using >"dpkg -i packagename". I have the Debian 2.1 "Slink" CD's. And I saw that I had XF86_VGA and not SVGA. So I got the SVGA from netgod and then X worked. Thanks Dada
Re: Debian on Sony 505TX
At 09:15 PM 11/5/1999 -0800, you wrote: >You want xserver-svga_3.3.3.1-2_i386.deb > >It would also be a good idea to get the latest versions of these >X .debs too: > > xserver-common > xfree86-common > xf86setup > xbase-clients > xlib6 > xlib6g > xfs > xfonts-scalable > xfonts-base > xfonts-75dpi > xfonts-100dpi > >There's an XF86Config file at http://bob.usuhs.mil/sony-pcg-505tx.html >that will probably do the job for you. The Debian 2.1 CD's I have, contain the older version of all those files. That is 3.3.2.3a-11 Also in the debian.org web pages I found only the old versions. But the http://www.netgod.net/x pages you pointed have all the latest versions of those files. That is 3.3.3.1-2 (Thanks God for netgod!) Dada
Hibernation
I have an IBM 365XD running 2.2.1 kernel. I have recompiled the kernel to support APM. I have been reading several websites that state that in order to use the hibernation feature on my laptop I have to create a dos partition on which a hibernation file can be saved. Unfortunately, I have all of my hard drive space used for my linux and swap partitions. Is there a simple way to add a new partition so I can use the hibernation feature on my laptop? Or does anyone know of another way which can be used to invoke hibernation using my current setup? (ie without having to repartition my HD). I hope that someone can offer some insight. David
Re: Hibernation
Hi! Maybe you want to look at this: http://falcon.sch.bme.hu/~seasons/linux/swsusp.html It's a patch to allow hibernation to your swap. I didn't test it yet but I'm at it. Hth Tobias --- Tobias Bachmor Department of Computer Science Concordia University at Montreal/Canada ---
Re: Xircom Ethernet/Modem problem
I have the same card, upgrade your kernel to >= 2.2.13. It fixed my problem. On Mon, 8 Nov 1999, Mesman, Ben wrote: > I have a Dell Lattitude CP with a Xircom 33k6 Eth/modem combo. I installed > slink with no problems. The card is recognised and configured properly and > the ethernet device works. > Problem is the modem. I can see no errors in the syslog file (attached), but > sending ATZ to the modem has no effect. > I read some HOWTO's and README files, but have not found the problem or the > solution. > > Does this ring a bell to you, or have you got any suggestions where to look? > please tell me! > > Greating, > Ben Mesman. > > --- Part of syslog --- > Nov 5 09:15:07 nl1019 cardmgr[103]: starting, version is 3.0.5 > Nov 5 09:15:07 nl1019 cardmgr[103]: watching 2 sockets > Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x1000-0x17ff: excluding > nothing: probe failed. > Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x0100-0x04ff: excluding > 0x210-0x217 0x220-0x22f 0x290-0x297 0x378-0x37f 0x388-0x38f 0x4d0-0x4d7 > Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x0a00-0x0aff: clean. > Nov 5 09:15:07 nl1019 kerneld: started, pid=110, qid=0 > Nov 5 09:15:07 nl1019 cardmgr[103]: initializing socket 0 > Nov 5 09:15:07 nl1019 kernel: cs: memory probe 0xa000-0xa0ff: > clean. > Nov 5 09:15:07 nl1019 cardmgr[103]: socket 0: Xircom CEM33 Ethernet/Modem > Nov 5 09:15:07 nl1019 cardmgr[103]: executing: 'insmod > /lib/modules/2.0.36/pcmcia/xirc2ps_cs.o' > Nov 5 09:15:07 nl1019 kernel: xirc2ps_cs.c 1.29 1998/04/27 19:20:19 > (dd9jn+kvh) > Nov 5 09:15:07 nl1019 cardmgr[103]: executing: 'insmod > /lib/modules/2.0.36/pcmcia/serial_cs.o' > Nov 5 09:15:07 nl1019 kernel: eth0: Xircom: port 0x2d0, irq 3, hwaddr > 00:80:C7:74:30:DC > Nov 5 09:15:07 nl1019 kernel: tty03 at 0x02e8 (irq = 3) is a 16450 > Nov 5 09:15:07 nl1019 cardmgr[103]: executing: './network start eth0' > Nov 5 09:15:09 nl1019 kernel: eth0: switching to 10BaseT port > Nov 5 09:15:09 nl1019 kernel: eth0: media 10Base2, silicon revision 1 > Nov 5 09:15:10 nl1019 kernel: eth0: media 10Base2, silicon revision 1 > Nov 5 09:15:10 nl1019 cardmgr[103]: executing: './serial start ttyS3' > Nov 5 09:20:50 nl1019 kernel: registered device ppp0 > Nov 5 09:20:50 nl1019 pppd[192]: pppd 2.3.5 started by root, uid 0 > Nov 5 09:20:51 nl1019 chat[193]: abort on (BUSY) > Nov 5 09:20:51 nl1019 chat[193]: abort on (NO CARRIER) > Nov 5 09:20:51 nl1019 chat[193]: abort on (VOICE) > Nov 5 09:20:51 nl1019 chat[193]: abort on (NO DIALTONE) > Nov 5 09:20:51 nl1019 chat[193]: abort on (NO ANSWER) > Nov 5 09:20:51 nl1019 chat[193]: send (ATZ^M) > Nov 5 09:20:51 nl1019 chat[193]: expect (OK) > Nov 5 09:21:36 nl1019 chat[193]: alarm > Nov 5 09:21:36 nl1019 chat[193]: Failed > Nov 5 09:21:36 nl1019 pppd[192]: Connect script failed > Nov 5 09:21:37 nl1019 pppd[192]: Exit. > ---End--- > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] > >
Re: Xircom Ethernet/Modem problem
You may try this adress: http://hyper.stanford.edu/HyperNews/get/pcmcia/xircom.html It's a web page/e-mail list dedicated to Xircom drivers development. Nuno Faria "Mesman, Ben" wrote: > > I have a Dell Lattitude CP with a Xircom 33k6 Eth/modem combo. I installed > slink with no problems. The card is recognised and configured properly and > the ethernet device works. > Problem is the modem. I can see no errors in the syslog file (attached), but > sending ATZ to the modem has no effect. > I read some HOWTO's and README files, but have not found the problem or the > solution. > > Does this ring a bell to you, or have you got any suggestions where to look? > please tell me! > > Greating, > Ben Mesman. >
