I have the same card, upgrade your kernel to >= 2.2.13. It fixed my problem.
On Mon, 8 Nov 1999, Mesman, Ben wrote: > I have a Dell Lattitude CP with a Xircom 33k6 Eth/modem combo. I installed > slink with no problems. The card is recognised and configured properly and > the ethernet device works. > Problem is the modem. I can see no errors in the syslog file (attached), but > sending ATZ to the modem has no effect. > I read some HOWTO's and README files, but have not found the problem or the > solution. > > Does this ring a bell to you, or have you got any suggestions where to look? > please tell me! > > Greating, > Ben Mesman. > > --- Part of syslog --- > Nov 5 09:15:07 nl1019 cardmgr[103]: starting, version is 3.0.5 > Nov 5 09:15:07 nl1019 cardmgr[103]: watching 2 sockets > Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x1000-0x17ff: excluding > nothing: probe failed. > Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x0100-0x04ff: excluding > 0x210-0x217 0x220-0x22f 0x290-0x297 0x378-0x37f 0x388-0x38f 0x4d0-0x4d7 > Nov 5 09:15:07 nl1019 kernel: cs: IO port probe 0x0a00-0x0aff: clean. > Nov 5 09:15:07 nl1019 kerneld: started, pid=110, qid=0 > Nov 5 09:15:07 nl1019 cardmgr[103]: initializing socket 0 > Nov 5 09:15:07 nl1019 kernel: cs: memory probe 0xa0000000-0xa0ffffff: > clean. > Nov 5 09:15:07 nl1019 cardmgr[103]: socket 0: Xircom CEM33 Ethernet/Modem > Nov 5 09:15:07 nl1019 cardmgr[103]: executing: 'insmod > /lib/modules/2.0.36/pcmcia/xirc2ps_cs.o' > Nov 5 09:15:07 nl1019 kernel: xirc2ps_cs.c 1.29 1998/04/27 19:20:19 > (dd9jn+kvh) > Nov 5 09:15:07 nl1019 cardmgr[103]: executing: 'insmod > /lib/modules/2.0.36/pcmcia/serial_cs.o' > Nov 5 09:15:07 nl1019 kernel: eth0: Xircom: port 0x2d0, irq 3, hwaddr > 00:80:C7:74:30:DC > Nov 5 09:15:07 nl1019 kernel: tty03 at 0x02e8 (irq = 3) is a 16450 > Nov 5 09:15:07 nl1019 cardmgr[103]: executing: './network start eth0' > Nov 5 09:15:09 nl1019 kernel: eth0: switching to 10BaseT port > Nov 5 09:15:09 nl1019 kernel: eth0: media 10Base2, silicon revision 1 > Nov 5 09:15:10 nl1019 kernel: eth0: media 10Base2, silicon revision 1 > Nov 5 09:15:10 nl1019 cardmgr[103]: executing: './serial start ttyS3' > Nov 5 09:20:50 nl1019 kernel: registered device ppp0 > Nov 5 09:20:50 nl1019 pppd[192]: pppd 2.3.5 started by root, uid 0 > Nov 5 09:20:51 nl1019 chat[193]: abort on (BUSY) > Nov 5 09:20:51 nl1019 chat[193]: abort on (NO CARRIER) > Nov 5 09:20:51 nl1019 chat[193]: abort on (VOICE) > Nov 5 09:20:51 nl1019 chat[193]: abort on (NO DIALTONE) > Nov 5 09:20:51 nl1019 chat[193]: abort on (NO ANSWER) > Nov 5 09:20:51 nl1019 chat[193]: send (ATZ^M) > Nov 5 09:20:51 nl1019 chat[193]: expect (OK) > Nov 5 09:21:36 nl1019 chat[193]: alarm > Nov 5 09:21:36 nl1019 chat[193]: Failed > Nov 5 09:21:36 nl1019 pppd[192]: Connect script failed > Nov 5 09:21:37 nl1019 pppd[192]: Exit. > ---End--- > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] > >
