I do not have the blue dos application for 1232. Please let me know where can I get it.
Thanks in advance. ----- Original Message ----- From: "County Wide Comms" <[EMAIL PROTECTED]> To: "Support" <[EMAIL PROTECTED]> Cc: "Erling Lassesen" <[EMAIL PROTECTED]>; <kxt@kxthelp.com> Sent: Tuesday, September 13, 2005 10:32 PM Subject: Re: KX-T: First time 16SLC (KX-TD174DX) Card installation on KX-TD1232 > Support wrote: > >> While programming, that position 1 is the lower position and also I have >> tried all the alternative to see whether it works or not. But none work. >> I have also removed the cable and back in again. It is still not working. >> I wonder how I can be able to test it should be working or not. >> Is there any symptons or something which I can check the card is ok or >> not? >> >> Thanks in advance. >> >> >> >> >> >> ----- Original Message ----- From: "Erling Lassesen" <[EMAIL PROTECTED]> >> To: "'Support'" <[EMAIL PROTECTED]>; "'Shawn Ceanga'" >> <[EMAIL PROTECTED]> >> Cc: <kxt@kxthelp.com> >> Sent: Tuesday, September 13, 2005 8:15 PM >> Subject: RE: KX-T: First time 16SLC (KX-TD174DX) Card installation on >> KX-TD1232 >> >> >>> Did you remember when programming that Position 1 is the lower position? >>> Also, did you try re-inserting the ribbon cable connector? >>> >>> -----Original Message----- >>> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf >>> Of >>> Support >>> Sent: Tuesday, September 13, 2005 12:44 AM >>> To: Shawn Ceanga >>> Cc: kxt@kxthelp.com >>> Subject: Re: KX-T: First time 16SLC (KX-TD174DX) Card installation on >>> KX-TD1232 >>> >>> I have rebooted the system after the unit is installed. >>> And also rebooted again after the programming. >>> However, I still cannot hear the dail tone. >>> >>> >>> >>> >>> ----- Original Message ----- From: "Shawn Ceanga" >>> <[EMAIL PROTECTED]> >>> To: "Support" <[EMAIL PROTECTED]> >>> Cc: <kxt@kxthelp.com> >>> Sent: Monday, September 12, 2005 3:37 PM >>> Subject: Re: KX-T: First time 16SLC (KX-TD174DX) Card installation on >>> KX-TD1232 >>> >>> >>>> Support wrote: >>>> >>>>> Hi, >>>>> >>>>> This is my first time installing the expension modules on 1232 pbx. >>>>> I'm installing 16SLC Card (KX-TD174DX) and KX-TD1232 PBX. >>>>> I have installed it in the expension area 1 and put the internal screw >>>>> already. >>>>> I programmed using #109 with A1,E2,C set. >>>>> However, I cannot be able to hear the dial tone when I attach a single >>>>> line telephone to the jack. >>>>> It has 8 Jacks on the board with 4 pins each. I tried to connect the >>>>> single line telephone on pin 1,2, but it didn't work. >>>>> So I tried to connect the single line telephone on pin 2,3 and still >>>>> it is >>>> >>> >>>>> not working. >>>>> I tried on pin 1,4 as well but it didn't work either. >>>>> So, I think I'm missing on the cable assignments or am I missing on >>>>> the >>>>> programming feature? >>>>> Your helps would be greatly appreciated. >>>>> >>>>> Arnold. >>>>> _________________________________________________________________ >>>>> KX-T Mailing list --- http://kxthelp.com/ >>>>> Subscription changes: http://kxthelp.com/mailman/listinfo/kxt >>>>> >>>>> >>>>> >>>> did you reboot the system?are you sure its in slot 1 ? >>>> >>>> >>> >>> >>> _________________________________________________________________ >>> KX-T Mailing list --- http://kxthelp.com/ >>> Subscription changes: http://kxthelp.com/mailman/listinfo/kxt >>> >>> >>> >>> >> >> >> > yes there is diagnostic tests that can be done do you have the blue dos > for the 1232? > > > _________________________________________________________________ KX-T Mailing list --- http://kxthelp.com/ Subscription changes: http://kxthelp.com/mailman/listinfo/kxt
