I probably looked in the index and found nothing. Something like that needs to be in the index. I almost always use an index before looking at the table of contents when I search for something. I am a believer in that an index is a rich information source (or should be) and should contain a lot more information than just page number look up such as cross references, associations, and even new information when it fits the content.
phil On Apr 9, 2014, at 9:31 PM, Jim Bennett <[email protected]> wrote: > It be on page 147 in my book. Figure 9.17 shows a complete > K3-->KPA500-->KAT500 setup. This is exactly how I've got mine set up. Nothing > in the index, but it is in the TOC in the front. :-) > > Jim / W6JHB > > > On Wednesday, Apr 9, 2014, at Wednesday, 9:25 PM, Phil Wheeler wrote: > >> Surprising, because I couldn't find any mention of the KPA500 in his K3 book >> by searching the pdf version. Maybe I did a typo. >> >> 73, Phil W7OX >> >> On 4/9/14, 8:55 PM, Phil Hystad wrote: >>> Jim, >>> >>> I think you mentioned the Cady KX3 book to me on a previous similar >>> message. If not, it was someone else. But, at that time, I searched for >>> the diagram and could not find it. Upon the message below I searched >>> again, page by page. Finally found it. Now, I looked in the >>> table-of-contents but for some strange reason I never saw that section on >>> the KX3 and KPA500. >>> >>> I do have a Diamond CX-210 two-position switch. I have a bunch of those in >>> my shack, also one 3 position. >>> >>> 73, phil, K7PEH >>> >>> >>> On Apr 9, 2014, at 7:29 PM, Jim Bennett <[email protected]> wrote: >>> >>>> phil, >>>> >>>> I'm doing exactly that - I have a KX3 and a K3 that share a KPA500, >>>> KAT500, and several antennas. I went by the diagram in Fred Cady's book on >>>> the KX3. Works like a charm. I can get up to 250 watts out with the KX3 >>>> driving the amp at 12 watts. And, no, I do not disconnect anything when I >>>> want to use the KX3 with the amp and tuner. Just make sure that (1) the K3 >>>> is powered off if you are using the KX3, and (2) your coax switch >>>> connecting the two radios to the amp has very good isolation. I'm using a >>>> two position Daiwa coax switch at the moment. >>>> >>>> Let me know if you need more info. I've been using this configuration for >>>> a few months now. >>>> >>>> Jim / W6JHB >>>> >>>> >>>> On Wednesday, Apr 9, 2014, at Wednesday, 4:23 PM, Phil Hystad wrote: >>>> >>>>> I am planning on configuring my KX3 to use the KPA500 and the KAT500. >>>>> Has anyone done this and what did you need to do? I already know how to >>>>> hook up the KX3 to the KPA500 but would like to hear from someone using >>>>> all three together. In particular, connections between KPA500 and KAT500. >>>>> >>>>> Also, follow up question -- if you have a configuration where you switch >>>>> KX3 and K3 driving the KPA500+KAT500 do you disconnect any K3 involved >>>>> AUX cables? I presume you would run with the K3 powered off if you are >>>>> driving with a KX3. >>>>> >>>>> Thanks, >>>>> >>>>> 73, phil, K7PEH >> > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
