I replaced my WBX boards with rev 3 and it looks like its working now. However, I would still like to be able to run the calibration routines on the rev 2 versions. Are you guys going to support this?
- Jan sirjanselot wrote: > > My UHD version is UHD_003.004.000-325-g7e296167 > > I opened up my USRP N210s and it seems like on each board it says two > different rev numbers. > > On all boards it shows WBX Board Rev. 2 on the main board while on the > connector board (the board with the RX and TX connectors on it) it says > WBX-FE-Simple Board Rev 4.0. > > I think my boards are about a year old. > > I installed gnuradio and uhd this saturday. > > - Jan > > > Marcus D. Leech wrote: >> >> >> >> What version of UHD are you running? And what approximate age are >> the WBX? >> >> The Rev 3 WBX is somewhat different than Rev 2, so you need >> to make sure that you have the latest host-side UHD and matching >> firmware to properly support Rev 3 WBX. >> >> There was a (transient) bug in >> the calibration routines that was found last week, but it's fixed in the >> most recent UHD host-side. >> >> I used the cal routines on my USRP2+WBX >> just this past weekeend and they worked just fine. So perhaps you have >> the transiently-broken version of UHD. >> >> Perhaps Josh can comment--I >> don't have the GIT tags of the broken instance at my fingertips right >> now. >> >> On Mon, 19 Mar 2012 08:36:43 -0700 (PDT), sirjanselot wrote: >> >>> >> Hello, >>> >>> I reran the command for each individual USRP radio >> connected. >>> >>> Two of my USRP N210s have this output: >>> >>> Error: RX >> dboard has empty serial! >>> >>> One of my USRP N210 has this output: >>> >> Error: timed out waiting for TX and/or RX LO to lock >>> >>> and the >> USRP1: >>> >>> Error: self-calibration is not supported for this >> hardware. >>> >>> I can understand if the self-calibration is not supported >> for the USRP1. >>> >>> However, for the USRP N210s I would like these >> fixed. I ran uhd_usrp_probe >>> and it seems like by dboard has a serial. >> It says TX Dboard: A ID: >>> WBX(0x0052). >>> >>> Is there a bug in the >> calibration routines? >>> >>> Marcus D. Leech wrote: >>>> When you have more >> than one USRP device connected to your system, you really should be >> explicit about which device you want to address, using the "--args" >> option. For your N210 it would be "--args addr=192.168.X.Y" and for your >> USRP1 it would be "type=usrp1" Otherwise, it just grabs the first USRP >> device it finds. On Mon, 19 Mar 2012 07:47:03 -0700 (PDT), sirjanselot >> wrote: >>>> >>>>> Hello, I was >>>> running the calibration routines for 3 >> USRP N210s and one 1 USRP >>>> >>>>> >>>> radio. I had them all connected >> at once to my computer and all of a sudden it >>>> >>>>> ow do I fix >> this? >>>> -left:#1010ff 2px solid; margin-left:5px; width:100%"> Does the >> calibration routines run for all of them @ once, when I call the - Jan >> _______________________________________________ Discuss-gnuradio mailing >> list >> >> >> _______________________________________________ >> Discuss-gnuradio mailing list >> Discuss-gnuradio@gnu.org >> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio >> >> > > -- View this message in context: http://old.nabble.com/Rx-dBoard-has-empty-serial-tp33532071p33533072.html Sent from the GnuRadio mailing list archive at Nabble.com. _______________________________________________ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
