Hi Rushikesh Ghatkar

I think you missed a "-f". The command line should be

*openocd -f interface/stlink-v3.cfg -f target/nucleo-h743zi2.cfg*

I use a command like the one below to to write the nuttx image

* openocd -f interface/stlink.cfg -f target/stm32g4x.cfg -c init -c "reset
halt" -c "flash write_image erase nuttx.bin 0x08000000" -c "exit"*

BR

Daniel


Em qua., 11 de ago. de 2021 07:26, rushi ghatkar <rushighatka...@gmail.com>
escreveu:

> Hi Alan Sir,
>
> Thanks for your instructions.
> As per your steps, I have followed.
> OpenOCD is not  working. Here in Nucleo-H743zi2, stlink-v3 is available.
> So I have tried the command : *openocd -f interface/stlink-v3.cfg
> target/nucleo-h743zi2.cfg* , gives error, please find the *openocd__error*
> screenshot attached.
>
> So, Instead of openocd I have tried STM32CubeProgrammer to flash the*
> nuttx.bin* file on board and the file downloaded successfully.
> And the solid LED is there. Please find the image attached.
>
> Is that right? Code got flashed?
>
>
>
> Regards,
> Rushikesh Ghatkar
>
> On Tue, Aug 10, 2021 at 6:08 PM Alan Carvalho de Assis <acas...@gmail.com>
> wrote:
>
>> Hi Rushikesh,
>>
>> I think you are doing the right steps, but just to confirm:
>>
>> $ make distclean
>>
>> $ ./tools/configure.sh nucleo-h743zi2:nsh
>>
>> $ make menuconfig     (this step is optional, just confirm that Device
>> Drivers  ---> [*] Serial Driver Support  ---> Serial console (USART3)
>> is correctly defined)
>>
>> $ make
>>
>> (flash firmware nuttx.bin in your board: you can use openocd or other
>> tool, no problem)
>>
>> Besides the "nsh>" another indication that NuttX is starting is a
>> solid LED turning ON, if it is crashing you should see an LED
>> blinking.
>>
>> BR,
>>
>> Alan
>>
>> On 8/10/21, rushi ghatkar <rushighatka...@gmail.com> wrote:
>> > Hi Sir,
>> >
>> > Thanks for your reply.
>> >
>> > I have a Nucleo-H743ZI2 board and followed a youtube video of Nuttx
>> channel
>> > to configure, compile and flash Nuttx rtos in Nucleo-H743ZI2 board.
>> > Youtube Link :
>> >
>> https://www.youtube.com/watch?v=heSkSd-_70g&list=PLd73yQk5Fd8JEsVD-lhwYRQKVu6glfDa8&index=1
>> >
>> > I did exactly as it is and finally the nuttx.bin file has been created
>> and
>> > I have flashed it by using STM32CubeProgrammer.
>> >
>> > For Nuttx configuration and compilation, I'm using Ubuntu 20.04.
>> > Picocom or minicom is not working, so I'm working on it to get it work.
>> >
>> > But now I have doubts,
>> > 1. How to create our own driver?  I want to create my own driver like
>> PWM,
>> > ADC and for other peripherals, for this where I should start to create?
>> and
>> > how??
>> > 2. To create our own driver, where do we have to create it like in
>> Ubuntu
>> > or is there any other IDE we can use in ubuntu?
>> > 3. After flashing the nuttx.bin file into Nucleo-H743ZI2 board, is it
>> > possible to do programming in STM32CubeIDE while the nuttx.bin file is
>> > already on board?
>> >
>> >
>> > Thanks & Regards,
>> > Rushikesh Ghatkar
>> >
>> >
>> > On Tue, Aug 10, 2021 at 3:52 PM Simon Filgis
>> > <si...@ingenieurbuero-filgis.de>
>> > wrote:
>> >
>> >> Hi Sir,
>> >>
>> >> split you problem:
>> >>
>> >> Have you verified that you're able to receive data with your PC from
>> any
>> >> known working embedded device.
>> >>
>> >> Best,
>> >>
>> >> Simon
>> >>
>> >>
>> >> On Tue, Aug 10, 2021 at 12:11 PM rushi ghatkar <
>> rushighatka...@gmail.com>
>> >> wrote:
>> >>
>> >> > Hi Sir,
>> >> >
>> >> > Thanks. Appreciate for your help.
>> >> >
>> >> > I have flashed your firmware file, nuttx.bin , but still I'm not
>> >> > getting
>> >> > nsh> prompt.
>> >> >
>> >> > Its ok sir. Thanks for your help.
>> >> >
>> >> >
>> >> >
>> >> > Thanks & Regards,
>> >> > Rushikesh Ghatkar
>> >> >
>> >> > On Tue, Aug 10, 2021 at 3:29 PM Murat Tologlu <mtolo...@hotmail.com>
>> >> > wrote:
>> >> >
>> >> > > Hi,
>> >> > >
>> >> > > Your nuttx.bin is probably different than the nuttx.bin file which
>> I
>> >> sent
>> >> > > to you that's why I configured and compiled an sent to you a new
>> one
>> >> for
>> >> > > your sake; If you still can't get  the nsh> prompt with the
>> firmware
>> >> > > I
>> >> > sent
>> >> > > to you I don't have any more answer for you. Maybe someone else can
>> >> > > contribute.
>> >> > >
>> >> > > Good luck.
>> >> > >
>> >> > > From: rushi ghatkar <rushighatka...@gmail.com>
>> >> > > Sent: Tuesday, August 10, 2021 12:24 PM
>> >> > > To: dev@nuttx.apache.org
>> >> > > Subject: Re: Nuttx RTOS with Nucleo-H743ZI2 board
>> >> > >
>> >> > >
>> >> > >
>> >> > > On Tue, Aug 10, 2021 at 2:52 PM rushi ghatkar <
>> >> rushighatka...@gmail.com
>> >> > > <mailto:rushighatka...@gmail.com>> wrote:
>> >> > > Hi Sir,
>> >> > >
>> >> > > Thanks for your reply. Really appreciate it.
>> >> > >
>> >> > > When i configured and compiled nuttx rtos then in my system
>> nuttx.bin
>> >> > file
>> >> > > was created. And I have flashed that file also. Please find the
>> nuttx
>> >> > > directory image attachment.
>> >> > >
>> >> > > Your firmware file, nuttx bin file I have flashed successfully
>> using
>> >> > > STM32CubeProgramer.
>> >> > >
>> >> > > But the issue is,
>> >> > > 1. picocom or minicom is not working.
>> >> > > 2. I want to create my own driver like PWM, ADC and for other
>> >> > peripherals,
>> >> > > for this where I should start to create? and how?
>> >> > >
>> >> > >
>> >> > > Thanks & Regards,
>> >> > > Rushikesh Ghatkar
>> >> > >
>> >> > >
>> >> > >
>> >> > >
>> >> > > On Tue, Aug 10, 2021 at 2:33 PM Murat Tologlu <
>> mtolo...@hotmail.com
>> >> > > <mailto:mtolo...@hotmail.com>> wrote:
>> >> > > Hi Rushikesh,
>> >> > >
>> >> > > Flash and try attached firmware ( you may try bin and hex files )
>> and
>> >> > tell
>> >> > > us what happens.
>> >> > >
>> >> > > Good luck,
>> >> > > Murat
>> >> > >
>> >> > > From: rushi ghatkar <rushighatka...@gmail.com<mailto:
>> >> > > rushighatka...@gmail.com>>
>> >> > > Sent: Tuesday, August 10, 2021 9:42 AM
>> >> > > To: dev@nuttx.apache.org<mailto:dev@nuttx.apache.org>
>> >> > > Subject: Re: Nuttx RTOS with Nucleo-H743ZI2 board
>> >> > >
>> >> > > Hi,
>> >> > >
>> >> > > Thanks for your reply.
>> >> > >
>> >> > > I have followed this youtube video from Nuttx Channel,
>> >> > >
>> >> > >
>> >> >
>> >>
>> https://www.youtube.com/watch?v=heSkSd-_70g&list=PLd73yQk5Fd8JEsVD-lhwYRQKVu6glfDa8&index=1
>> >> > >
>> >> > > From the above link I have followed each step exactly as it is.
>> >> > >
>> >> > > I'm using Nucleo-H743ZI2 board which has stlink-v3, for this in the
>> >> end I
>> >> > > was trying to execute command "openocd -f interface/stlink-v3.cfg
>> -f
>> >> > > target/stm32h7x.cfg" but this gives error. Please find the error
>> >> > > image
>> >> > > attachment.
>> >> > > As you asked, use STM32CubeProgrammer to flash nuttx.bin into the
>> >> > > Nucleo-H743ZI2 board. And I used it and the nuttx.bin file has been
>> >> > flashed
>> >> > > successfully.
>> >> > >
>> >> > > After all this I was trying to open the nutshell using picocom, but
>> >> > > nothing happened. No nutshell prompt appeared.
>> >> > >
>> >> > > Please help me to solve this issue.
>> >> > >
>> >> > >
>> >> > > Thanks & Regards,
>> >> > > Rushikesh Ghatkar
>> >> > >
>> >> > >
>> >> > > On Tue, Aug 10, 2021 at 11:39 AM murat tologlu <
>> mtolo...@hotmail.com
>> >> > > <mailto:mtolo...@hotmail.com>> wrote:
>> >> > > Hi Rushikesh,
>> >> > >
>> >> > > If you copy paste and share in a file attachment all the command
>> line
>> >> > > content from "$ cd nuttxspace/nuttx" to the end - not only picocom
>> >> > output "
>> >> > > but everything that you did to configure and compile fooling "a
>> >> > > video"
>> >> (
>> >> > > which video? ) , perhaps we help can you.
>> >> > >
>> >> > > Regards,
>> >> > > Murat
>> >> > >
>> >> > > On 2021/08/10 05:00:36, rushi ghatkar <rushighatka...@gmail.com
>> >> <mailto:
>> >> > > rushighatka...@gmail.com>> wrote:
>> >> > > > Hi,
>> >> > > >
>> >> > > > I have followed a youtube video from Nuttx Channel to configure
>> and
>> >> > > compile
>> >> > > > Nuttx rtos with Nucleo-H743ZI2. And with the help of
>> >> > STM32CUbeProgrammer
>> >> > > I
>> >> > > > have also flashed the nuttx.bin file into the board.
>> >> > > > But when I was trying to use minicom or picocom, I'm unable to
>> use
>> >> it.
>> >> > > > After executing this command "*sudo picocom /dev/ttyACM0 -b
>> 115200"
>> >> *,
>> >> > > > nutshell prompt is not appearing, please find the attachment.
>> >> > > > Need help for this.
>> >> > > >
>> >> > > >
>> >> > > > Regards,
>> >> > > > Rushikesh Ghatkar
>> >> > > >
>> >> > > > On Mon, Aug 9, 2021 at 8:17 PM murat tologlu <
>> mtolo...@hotmail.com
>> >> > > <mailto:mtolo...@hotmail.com>> wrote:
>> >> > > >
>> >> > > > > Hi Rushi,
>> >> > > > >
>> >> > > > > Unless we know what you are trying to do we can't help you.
>> There
>> >> may
>> >> > > be a
>> >> > > > > mistake anywhere!
>> >> > > > >
>> >> > > > > Explain what did you try so far, how ? Give us the links of the
>> >> > > > > application you're trying.. So may be we can discover your
>> >> > > > > mistake.
>> >> > > > >
>> >> > > > > Regards,
>> >> > > > > Murat
>> >> > > > >
>> >> > > > > On 2021/08/09 04:36:22, rushi ghatkar <
>> rushighatka...@gmail.com
>> >> > > <mailto:rushighatka...@gmail.com>> wrote:
>> >> > > > > > Hi,
>> >> > > > > >
>> >> > > > > > I'm totally new to NUttx RTOS and I have started to work on
>> it.
>> >> > > > > > I
>> >> > > have a
>> >> > > > > > Nucleo-H743ZI2 board and followed a youtube video of Nuttx
>> >> channel
>> >> > to
>> >> > > > > > configure, compile and flash Nuttx rtos in Nucleo-H743ZI2
>> >> > > > > > board.
>> >> > > After
>> >> > > > > > compilation nuttx.bin file has been created but to flash that
>> >> > > > > > on
>> >> > > board,
>> >> > > > > > flash command is not working so I tried STM32CubeProgrammer
>> to
>> >> > flash
>> >> > > and
>> >> > > > > it
>> >> > > > > > got flash successfully.
>> >> > > > > > But after that "sudo picocom/dev/ttyACM0 -b 115200" , after
>> >> > > executing and
>> >> > > > > > resetting the board  it's just waiting but the nsh> prompt
>> >> > > > > > isn't
>> >> > > > > appearing.
>> >> > > > > > What to do about it?
>> >> > > > > >
>> >> > > > > > Is there anyone who has worked on Nuttx RTOS with
>> >> > > > > > Nucleo-H743ZI2
>> >> > > board
>> >> > > > > and
>> >> > > > > > can help me with this issue?
>> >> > > > > > Please help me to solve this issue.
>> >> > > > > > And also I want to create my own driver using nuttx rtos on a
>> >> > > > > Nucleo-H73ZI2
>> >> > > > > > board . How to create our own driver and which IDE we have to
>> >> use?
>> >> > > > > >
>> >> > > > > > Please help me.
>> >> > > > > >
>> >> > > > > >
>> >> > > > > >
>> >> > > > > > Thanks & Regards,
>> >> > > > > > Rushikesh Ghatkar
>> >> > > > > >
>> >> > > > >
>> >> > > >
>> >> > >
>> >> >
>> >>
>> >
>>
>

Reply via email to