Hi Rushikesh,

Congratulations!!!

What was the issue?

BR,

Alan

On 8/11/21, rushi ghatkar <rushighatka...@gmail.com> wrote:
> Hi @Brennan @Alan Sir,
>
> I have tried to install and configure NUttx RTOS and completed
> successfully.
> Both* nuttx.bin* and *nuttx.hex* files have been created.
>
> Now Picocom is also working properly, please find the image attachment.
> And yes it was* /dev/ttyACM0 *for the driver.
>
>
> Thanks for your help sir.
> Really appreciate it.
>
> Regards,
> Rushikesh Ghatkar
>
>
> On Wed, Aug 11, 2021 at 5:18 PM Alan Carvalho de Assis <acas...@gmail.com>
> wrote:
>
>> Hi Rushikesh,
>>
>> Yes, seams like the NuttX was initialized correctly.
>>
>> There are some possible reason why you are not seem the NSH terminal:
>>
>> - Are you sure that /dev/ttyACM0 is from you board (case there are
>> other board or USB modem on your computer, please remove it)
>>
>> - Maybe the STLink in the board is not connected to the right pins of
>> the USART3 (PD9 and PD8) ou it needs some jumpers (I don't have this
>> board to confirm)
>>
>> Do you have flashed same example from ST that used the serial on
>> USART3 to confirm it is working?
>>
>> Also, please try to use the same openocd command that Brennan used:
>>
>> openocd -f board/stm32h745i-disco.cfg -c "program nuttx verify reset
>> exit"
>>
>> Since it is working for him, it needs to work on your board too.
>>
>> BR,
>>
>> Alan
>>
>> On 8/11/21, rushi ghatkar <rushighatka...@gmail.com> wrote:
>> > Hi Alan Sir,
>> >
>> > Thanks for your instructions.
>> > As per your steps, I have followed.
>> > OpenOCD is not  working. Here in Nucleo-H743zi2, stlink-v3 is
>> > available.
>> So
>> > I have tried the command : *openocd -f interface/stlink-v3.cfg
>> > target/nucleo-h743zi2.cfg* , gives error, please find the
>> *openocd__error*
>> > screenshot attached.
>> >
>> > So, Instead of openocd I have tried STM32CubeProgrammer to flash the*
>> > nuttx.bin* file on board and the file downloaded successfully.
>> > And the solid LED is there. Please find the image attached.
>> >
>> > Is that right? Code got flashed?
>> >
>> >
>> >
>> > Regards,
>> > Rushikesh Ghatkar
>> >
>> > On Tue, Aug 10, 2021 at 6:08 PM Alan Carvalho de Assis <
>> acas...@gmail.com>
>> > wrote:
>> >
>> >> Hi Rushikesh,
>> >>
>> >> I think you are doing the right steps, but just to confirm:
>> >>
>> >> $ make distclean
>> >>
>> >> $ ./tools/configure.sh nucleo-h743zi2:nsh
>> >>
>> >> $ make menuconfig     (this step is optional, just confirm that Device
>> >> Drivers  ---> [*] Serial Driver Support  ---> Serial console (USART3)
>> >> is correctly defined)
>> >>
>> >> $ make
>> >>
>> >> (flash firmware nuttx.bin in your board: you can use openocd or other
>> >> tool, no problem)
>> >>
>> >> Besides the "nsh>" another indication that NuttX is starting is a
>> >> solid LED turning ON, if it is crashing you should see an LED
>> >> blinking.
>> >>
>> >> BR,
>> >>
>> >> Alan
>> >>
>> >> On 8/10/21, rushi ghatkar <rushighatka...@gmail.com> wrote:
>> >> > Hi Sir,
>> >> >
>> >> > Thanks for your reply.
>> >> >
>> >> > I have a Nucleo-H743ZI2 board and followed a youtube video of Nuttx
>> >> channel
>> >> > to configure, compile and flash Nuttx rtos in Nucleo-H743ZI2 board.
>> >> > Youtube Link :
>> >> >
>> >>
>> https://www.youtube.com/watch?v=heSkSd-_70g&list=PLd73yQk5Fd8JEsVD-lhwYRQKVu6glfDa8&index=1
>> >> >
>> >> > I did exactly as it is and finally the nuttx.bin file has been
>> >> > created
>> >> and
>> >> > I have flashed it by using STM32CubeProgrammer.
>> >> >
>> >> > For Nuttx configuration and compilation, I'm using Ubuntu 20.04.
>> >> > Picocom or minicom is not working, so I'm working on it to get it
>> work.
>> >> >
>> >> > But now I have doubts,
>> >> > 1. How to create our own driver?  I want to create my own driver
>> >> > like
>> >> PWM,
>> >> > ADC and for other peripherals, for this where I should start to
>> create?
>> >> and
>> >> > how??
>> >> > 2. To create our own driver, where do we have to create it like in
>> >> > Ubuntu
>> >> > or is there any other IDE we can use in ubuntu?
>> >> > 3. After flashing the nuttx.bin file into Nucleo-H743ZI2 board, is
>> >> > it
>> >> > possible to do programming in STM32CubeIDE while the nuttx.bin file
>> >> > is
>> >> > already on board?
>> >> >
>> >> >
>> >> > Thanks & Regards,
>> >> > Rushikesh Ghatkar
>> >> >
>> >> >
>> >> > On Tue, Aug 10, 2021 at 3:52 PM Simon Filgis
>> >> > <si...@ingenieurbuero-filgis.de>
>> >> > wrote:
>> >> >
>> >> >> Hi Sir,
>> >> >>
>> >> >> split you problem:
>> >> >>
>> >> >> Have you verified that you're able to receive data with your PC
>> >> >> from
>> >> >> any
>> >> >> known working embedded device.
>> >> >>
>> >> >> Best,
>> >> >>
>> >> >> Simon
>> >> >>
>> >> >>
>> >> >> On Tue, Aug 10, 2021 at 12:11 PM rushi ghatkar <
>> >> rushighatka...@gmail.com>
>> >> >> wrote:
>> >> >>
>> >> >> > Hi Sir,
>> >> >> >
>> >> >> > Thanks. Appreciate for your help.
>> >> >> >
>> >> >> > I have flashed your firmware file, nuttx.bin , but still I'm not
>> >> >> > getting
>> >> >> > nsh> prompt.
>> >> >> >
>> >> >> > Its ok sir. Thanks for your help.
>> >> >> >
>> >> >> >
>> >> >> >
>> >> >> > Thanks & Regards,
>> >> >> > Rushikesh Ghatkar
>> >> >> >
>> >> >> > On Tue, Aug 10, 2021 at 3:29 PM Murat Tologlu <
>> mtolo...@hotmail.com>
>> >> >> > wrote:
>> >> >> >
>> >> >> > > Hi,
>> >> >> > >
>> >> >> > > Your nuttx.bin is probably different than the nuttx.bin file
>> which
>> >> >> > > I
>> >> >> sent
>> >> >> > > to you that's why I configured and compiled an sent to you a
>> >> >> > > new
>> >> >> > > one
>> >> >> for
>> >> >> > > your sake; If you still can't get  the nsh> prompt with the
>> >> >> > > firmware
>> >> >> > > I
>> >> >> > sent
>> >> >> > > to you I don't have any more answer for you. Maybe someone else
>> >> >> > > can
>> >> >> > > contribute.
>> >> >> > >
>> >> >> > > Good luck.
>> >> >> > >
>> >> >> > > From: rushi ghatkar <rushighatka...@gmail.com>
>> >> >> > > Sent: Tuesday, August 10, 2021 12:24 PM
>> >> >> > > To: dev@nuttx.apache.org
>> >> >> > > Subject: Re: Nuttx RTOS with Nucleo-H743ZI2 board
>> >> >> > >
>> >> >> > >
>> >> >> > >
>> >> >> > > On Tue, Aug 10, 2021 at 2:52 PM rushi ghatkar <
>> >> >> rushighatka...@gmail.com
>> >> >> > > <mailto:rushighatka...@gmail.com>> wrote:
>> >> >> > > Hi Sir,
>> >> >> > >
>> >> >> > > Thanks for your reply. Really appreciate it.
>> >> >> > >
>> >> >> > > When i configured and compiled nuttx rtos then in my system
>> >> nuttx.bin
>> >> >> > file
>> >> >> > > was created. And I have flashed that file also. Please find the
>> >> nuttx
>> >> >> > > directory image attachment.
>> >> >> > >
>> >> >> > > Your firmware file, nuttx bin file I have flashed successfully
>> >> >> > > using
>> >> >> > > STM32CubeProgramer.
>> >> >> > >
>> >> >> > > But the issue is,
>> >> >> > > 1. picocom or minicom is not working.
>> >> >> > > 2. I want to create my own driver like PWM, ADC and for other
>> >> >> > peripherals,
>> >> >> > > for this where I should start to create? and how?
>> >> >> > >
>> >> >> > >
>> >> >> > > Thanks & Regards,
>> >> >> > > Rushikesh Ghatkar
>> >> >> > >
>> >> >> > >
>> >> >> > >
>> >> >> > >
>> >> >> > > On Tue, Aug 10, 2021 at 2:33 PM Murat Tologlu
>> >> >> > > <mtolo...@hotmail.com
>> >> >> > > <mailto:mtolo...@hotmail.com>> wrote:
>> >> >> > > Hi Rushikesh,
>> >> >> > >
>> >> >> > > Flash and try attached firmware ( you may try bin and hex files
>> >> >> > > )
>> >> and
>> >> >> > tell
>> >> >> > > us what happens.
>> >> >> > >
>> >> >> > > Good luck,
>> >> >> > > Murat
>> >> >> > >
>> >> >> > > From: rushi ghatkar <rushighatka...@gmail.com<mailto:
>> >> >> > > rushighatka...@gmail.com>>
>> >> >> > > Sent: Tuesday, August 10, 2021 9:42 AM
>> >> >> > > To: dev@nuttx.apache.org<mailto:dev@nuttx.apache.org>
>> >> >> > > Subject: Re: Nuttx RTOS with Nucleo-H743ZI2 board
>> >> >> > >
>> >> >> > > Hi,
>> >> >> > >
>> >> >> > > Thanks for your reply.
>> >> >> > >
>> >> >> > > I have followed this youtube video from Nuttx Channel,
>> >> >> > >
>> >> >> > >
>> >> >> >
>> >> >>
>> >>
>> https://www.youtube.com/watch?v=heSkSd-_70g&list=PLd73yQk5Fd8JEsVD-lhwYRQKVu6glfDa8&index=1
>> >> >> > >
>> >> >> > > From the above link I have followed each step exactly as it is.
>> >> >> > >
>> >> >> > > I'm using Nucleo-H743ZI2 board which has stlink-v3, for this in
>> >> >> > > the
>> >> >> end I
>> >> >> > > was trying to execute command "openocd -f
>> >> >> > > interface/stlink-v3.cfg
>> >> >> > > -f
>> >> >> > > target/stm32h7x.cfg" but this gives error. Please find the
>> >> >> > > error
>> >> >> > > image
>> >> >> > > attachment.
>> >> >> > > As you asked, use STM32CubeProgrammer to flash nuttx.bin into
>> >> >> > > the
>> >> >> > > Nucleo-H743ZI2 board. And I used it and the nuttx.bin file has
>> >> >> > > been
>> >> >> > flashed
>> >> >> > > successfully.
>> >> >> > >
>> >> >> > > After all this I was trying to open the nutshell using picocom,
>> >> >> > > but
>> >> >> > > nothing happened. No nutshell prompt appeared.
>> >> >> > >
>> >> >> > > Please help me to solve this issue.
>> >> >> > >
>> >> >> > >
>> >> >> > > Thanks & Regards,
>> >> >> > > Rushikesh Ghatkar
>> >> >> > >
>> >> >> > >
>> >> >> > > On Tue, Aug 10, 2021 at 11:39 AM murat tologlu <
>> >> mtolo...@hotmail.com
>> >> >> > > <mailto:mtolo...@hotmail.com>> wrote:
>> >> >> > > Hi Rushikesh,
>> >> >> > >
>> >> >> > > If you copy paste and share in a file attachment all the
>> >> >> > > command
>> >> line
>> >> >> > > content from "$ cd nuttxspace/nuttx" to the end - not only
>> picocom
>> >> >> > output "
>> >> >> > > but everything that you did to configure and compile fooling "a
>> >> >> > > video"
>> >> >> (
>> >> >> > > which video? ) , perhaps we help can you.
>> >> >> > >
>> >> >> > > Regards,
>> >> >> > > Murat
>> >> >> > >
>> >> >> > > On 2021/08/10 05:00:36, rushi ghatkar <rushighatka...@gmail.com
>> >> >> <mailto:
>> >> >> > > rushighatka...@gmail.com>> wrote:
>> >> >> > > > Hi,
>> >> >> > > >
>> >> >> > > > I have followed a youtube video from Nuttx Channel to
>> >> >> > > > configure
>> >> and
>> >> >> > > compile
>> >> >> > > > Nuttx rtos with Nucleo-H743ZI2. And with the help of
>> >> >> > STM32CUbeProgrammer
>> >> >> > > I
>> >> >> > > > have also flashed the nuttx.bin file into the board.
>> >> >> > > > But when I was trying to use minicom or picocom, I'm unable
>> >> >> > > > to
>> >> >> > > > use
>> >> >> it.
>> >> >> > > > After executing this command "*sudo picocom /dev/ttyACM0 -b
>> >> 115200"
>> >> >> *,
>> >> >> > > > nutshell prompt is not appearing, please find the attachment.
>> >> >> > > > Need help for this.
>> >> >> > > >
>> >> >> > > >
>> >> >> > > > Regards,
>> >> >> > > > Rushikesh Ghatkar
>> >> >> > > >
>> >> >> > > > On Mon, Aug 9, 2021 at 8:17 PM murat tologlu <
>> >> mtolo...@hotmail.com
>> >> >> > > <mailto:mtolo...@hotmail.com>> wrote:
>> >> >> > > >
>> >> >> > > > > Hi Rushi,
>> >> >> > > > >
>> >> >> > > > > Unless we know what you are trying to do we can't help you.
>> >> There
>> >> >> may
>> >> >> > > be a
>> >> >> > > > > mistake anywhere!
>> >> >> > > > >
>> >> >> > > > > Explain what did you try so far, how ? Give us the links of
>> >> >> > > > > the
>> >> >> > > > > application you're trying.. So may be we can discover your
>> >> >> > > > > mistake.
>> >> >> > > > >
>> >> >> > > > > Regards,
>> >> >> > > > > Murat
>> >> >> > > > >
>> >> >> > > > > On 2021/08/09 04:36:22, rushi ghatkar
>> >> >> > > > > <rushighatka...@gmail.com
>> >> >> > > <mailto:rushighatka...@gmail.com>> wrote:
>> >> >> > > > > > Hi,
>> >> >> > > > > >
>> >> >> > > > > > I'm totally new to NUttx RTOS and I have started to work
>> >> >> > > > > > on
>> >> it.
>> >> >> > > > > > I
>> >> >> > > have a
>> >> >> > > > > > Nucleo-H743ZI2 board and followed a youtube video of
>> >> >> > > > > > Nuttx
>> >> >> channel
>> >> >> > to
>> >> >> > > > > > configure, compile and flash Nuttx rtos in Nucleo-H743ZI2
>> >> >> > > > > > board.
>> >> >> > > After
>> >> >> > > > > > compilation nuttx.bin file has been created but to flash
>> >> >> > > > > > that
>> >> >> > > > > > on
>> >> >> > > board,
>> >> >> > > > > > flash command is not working so I tried
>> >> >> > > > > > STM32CubeProgrammer
>> >> >> > > > > > to
>> >> >> > flash
>> >> >> > > and
>> >> >> > > > > it
>> >> >> > > > > > got flash successfully.
>> >> >> > > > > > But after that "sudo picocom/dev/ttyACM0 -b 115200" ,
>> >> >> > > > > > after
>> >> >> > > executing and
>> >> >> > > > > > resetting the board  it's just waiting but the nsh>
>> >> >> > > > > > prompt
>> >> >> > > > > > isn't
>> >> >> > > > > appearing.
>> >> >> > > > > > What to do about it?
>> >> >> > > > > >
>> >> >> > > > > > Is there anyone who has worked on Nuttx RTOS with
>> >> >> > > > > > Nucleo-H743ZI2
>> >> >> > > board
>> >> >> > > > > and
>> >> >> > > > > > can help me with this issue?
>> >> >> > > > > > Please help me to solve this issue.
>> >> >> > > > > > And also I want to create my own driver using nuttx rtos
>> >> >> > > > > > on
>> >> >> > > > > > a
>> >> >> > > > > Nucleo-H73ZI2
>> >> >> > > > > > board . How to create our own driver and which IDE we
>> >> >> > > > > > have
>> >> >> > > > > > to
>> >> >> use?
>> >> >> > > > > >
>> >> >> > > > > > Please help me.
>> >> >> > > > > >
>> >> >> > > > > >
>> >> >> > > > > >
>> >> >> > > > > > Thanks & Regards,
>> >> >> > > > > > Rushikesh Ghatkar
>> >> >> > > > > >
>> >> >> > > > >
>> >> >> > > >
>> >> >> > >
>> >> >> >
>> >> >>
>> >> >
>> >>
>> >
>>
>

Reply via email to