Hi Rushikesh,

I think you are doing the right steps, but just to confirm:

$ make distclean

$ ./tools/configure.sh nucleo-h743zi2:nsh

$ make menuconfig     (this step is optional, just confirm that Device
Drivers  ---> [*] Serial Driver Support  ---> Serial console (USART3)
is correctly defined)

$ make

(flash firmware nuttx.bin in your board: you can use openocd or other
tool, no problem)

Besides the "nsh>" another indication that NuttX is starting is a
solid LED turning ON, if it is crashing you should see an LED
blinking.

BR,

Alan

On 8/10/21, rushi ghatkar <rushighatka...@gmail.com> wrote:
> Hi Sir,
>
> Thanks for your reply.
>
> I have a Nucleo-H743ZI2 board and followed a youtube video of Nuttx channel
> to configure, compile and flash Nuttx rtos in Nucleo-H743ZI2 board.
> Youtube Link :
> https://www.youtube.com/watch?v=heSkSd-_70g&list=PLd73yQk5Fd8JEsVD-lhwYRQKVu6glfDa8&index=1
>
> I did exactly as it is and finally the nuttx.bin file has been created and
> I have flashed it by using STM32CubeProgrammer.
>
> For Nuttx configuration and compilation, I'm using Ubuntu 20.04.
> Picocom or minicom is not working, so I'm working on it to get it work.
>
> But now I have doubts,
> 1. How to create our own driver?  I want to create my own driver like PWM,
> ADC and for other peripherals, for this where I should start to create? and
> how??
> 2. To create our own driver, where do we have to create it like in Ubuntu
> or is there any other IDE we can use in ubuntu?
> 3. After flashing the nuttx.bin file into Nucleo-H743ZI2 board, is it
> possible to do programming in STM32CubeIDE while the nuttx.bin file is
> already on board?
>
>
> Thanks & Regards,
> Rushikesh Ghatkar
>
>
> On Tue, Aug 10, 2021 at 3:52 PM Simon Filgis
> <si...@ingenieurbuero-filgis.de>
> wrote:
>
>> Hi Sir,
>>
>> split you problem:
>>
>> Have you verified that you're able to receive data with your PC from any
>> known working embedded device.
>>
>> Best,
>>
>> Simon
>>
>>
>> On Tue, Aug 10, 2021 at 12:11 PM rushi ghatkar <rushighatka...@gmail.com>
>> wrote:
>>
>> > Hi Sir,
>> >
>> > Thanks. Appreciate for your help.
>> >
>> > I have flashed your firmware file, nuttx.bin , but still I'm not
>> > getting
>> > nsh> prompt.
>> >
>> > Its ok sir. Thanks for your help.
>> >
>> >
>> >
>> > Thanks & Regards,
>> > Rushikesh Ghatkar
>> >
>> > On Tue, Aug 10, 2021 at 3:29 PM Murat Tologlu <mtolo...@hotmail.com>
>> > wrote:
>> >
>> > > Hi,
>> > >
>> > > Your nuttx.bin is probably different than the nuttx.bin file which I
>> sent
>> > > to you that's why I configured and compiled an sent to you a new one
>> for
>> > > your sake; If you still can't get  the nsh> prompt with the firmware
>> > > I
>> > sent
>> > > to you I don't have any more answer for you. Maybe someone else can
>> > > contribute.
>> > >
>> > > Good luck.
>> > >
>> > > From: rushi ghatkar <rushighatka...@gmail.com>
>> > > Sent: Tuesday, August 10, 2021 12:24 PM
>> > > To: dev@nuttx.apache.org
>> > > Subject: Re: Nuttx RTOS with Nucleo-H743ZI2 board
>> > >
>> > >
>> > >
>> > > On Tue, Aug 10, 2021 at 2:52 PM rushi ghatkar <
>> rushighatka...@gmail.com
>> > > <mailto:rushighatka...@gmail.com>> wrote:
>> > > Hi Sir,
>> > >
>> > > Thanks for your reply. Really appreciate it.
>> > >
>> > > When i configured and compiled nuttx rtos then in my system nuttx.bin
>> > file
>> > > was created. And I have flashed that file also. Please find the nuttx
>> > > directory image attachment.
>> > >
>> > > Your firmware file, nuttx bin file I have flashed successfully using
>> > > STM32CubeProgramer.
>> > >
>> > > But the issue is,
>> > > 1. picocom or minicom is not working.
>> > > 2. I want to create my own driver like PWM, ADC and for other
>> > peripherals,
>> > > for this where I should start to create? and how?
>> > >
>> > >
>> > > Thanks & Regards,
>> > > Rushikesh Ghatkar
>> > >
>> > >
>> > >
>> > >
>> > > On Tue, Aug 10, 2021 at 2:33 PM Murat Tologlu <mtolo...@hotmail.com
>> > > <mailto:mtolo...@hotmail.com>> wrote:
>> > > Hi Rushikesh,
>> > >
>> > > Flash and try attached firmware ( you may try bin and hex files ) and
>> > tell
>> > > us what happens.
>> > >
>> > > Good luck,
>> > > Murat
>> > >
>> > > From: rushi ghatkar <rushighatka...@gmail.com<mailto:
>> > > rushighatka...@gmail.com>>
>> > > Sent: Tuesday, August 10, 2021 9:42 AM
>> > > To: dev@nuttx.apache.org<mailto:dev@nuttx.apache.org>
>> > > Subject: Re: Nuttx RTOS with Nucleo-H743ZI2 board
>> > >
>> > > Hi,
>> > >
>> > > Thanks for your reply.
>> > >
>> > > I have followed this youtube video from Nuttx Channel,
>> > >
>> > >
>> >
>> https://www.youtube.com/watch?v=heSkSd-_70g&list=PLd73yQk5Fd8JEsVD-lhwYRQKVu6glfDa8&index=1
>> > >
>> > > From the above link I have followed each step exactly as it is.
>> > >
>> > > I'm using Nucleo-H743ZI2 board which has stlink-v3, for this in the
>> end I
>> > > was trying to execute command "openocd -f interface/stlink-v3.cfg -f
>> > > target/stm32h7x.cfg" but this gives error. Please find the error
>> > > image
>> > > attachment.
>> > > As you asked, use STM32CubeProgrammer to flash nuttx.bin into the
>> > > Nucleo-H743ZI2 board. And I used it and the nuttx.bin file has been
>> > flashed
>> > > successfully.
>> > >
>> > > After all this I was trying to open the nutshell using picocom, but
>> > > nothing happened. No nutshell prompt appeared.
>> > >
>> > > Please help me to solve this issue.
>> > >
>> > >
>> > > Thanks & Regards,
>> > > Rushikesh Ghatkar
>> > >
>> > >
>> > > On Tue, Aug 10, 2021 at 11:39 AM murat tologlu <mtolo...@hotmail.com
>> > > <mailto:mtolo...@hotmail.com>> wrote:
>> > > Hi Rushikesh,
>> > >
>> > > If you copy paste and share in a file attachment all the command line
>> > > content from "$ cd nuttxspace/nuttx" to the end - not only picocom
>> > output "
>> > > but everything that you did to configure and compile fooling "a
>> > > video"
>> (
>> > > which video? ) , perhaps we help can you.
>> > >
>> > > Regards,
>> > > Murat
>> > >
>> > > On 2021/08/10 05:00:36, rushi ghatkar <rushighatka...@gmail.com
>> <mailto:
>> > > rushighatka...@gmail.com>> wrote:
>> > > > Hi,
>> > > >
>> > > > I have followed a youtube video from Nuttx Channel to configure and
>> > > compile
>> > > > Nuttx rtos with Nucleo-H743ZI2. And with the help of
>> > STM32CUbeProgrammer
>> > > I
>> > > > have also flashed the nuttx.bin file into the board.
>> > > > But when I was trying to use minicom or picocom, I'm unable to use
>> it.
>> > > > After executing this command "*sudo picocom /dev/ttyACM0 -b 115200"
>> *,
>> > > > nutshell prompt is not appearing, please find the attachment.
>> > > > Need help for this.
>> > > >
>> > > >
>> > > > Regards,
>> > > > Rushikesh Ghatkar
>> > > >
>> > > > On Mon, Aug 9, 2021 at 8:17 PM murat tologlu <mtolo...@hotmail.com
>> > > <mailto:mtolo...@hotmail.com>> wrote:
>> > > >
>> > > > > Hi Rushi,
>> > > > >
>> > > > > Unless we know what you are trying to do we can't help you. There
>> may
>> > > be a
>> > > > > mistake anywhere!
>> > > > >
>> > > > > Explain what did you try so far, how ? Give us the links of the
>> > > > > application you're trying.. So may be we can discover your
>> > > > > mistake.
>> > > > >
>> > > > > Regards,
>> > > > > Murat
>> > > > >
>> > > > > On 2021/08/09 04:36:22, rushi ghatkar <rushighatka...@gmail.com
>> > > <mailto:rushighatka...@gmail.com>> wrote:
>> > > > > > Hi,
>> > > > > >
>> > > > > > I'm totally new to NUttx RTOS and I have started to work on it.
>> > > > > > I
>> > > have a
>> > > > > > Nucleo-H743ZI2 board and followed a youtube video of Nuttx
>> channel
>> > to
>> > > > > > configure, compile and flash Nuttx rtos in Nucleo-H743ZI2
>> > > > > > board.
>> > > After
>> > > > > > compilation nuttx.bin file has been created but to flash that
>> > > > > > on
>> > > board,
>> > > > > > flash command is not working so I tried STM32CubeProgrammer to
>> > flash
>> > > and
>> > > > > it
>> > > > > > got flash successfully.
>> > > > > > But after that "sudo picocom/dev/ttyACM0 -b 115200" , after
>> > > executing and
>> > > > > > resetting the board  it's just waiting but the nsh> prompt
>> > > > > > isn't
>> > > > > appearing.
>> > > > > > What to do about it?
>> > > > > >
>> > > > > > Is there anyone who has worked on Nuttx RTOS with
>> > > > > > Nucleo-H743ZI2
>> > > board
>> > > > > and
>> > > > > > can help me with this issue?
>> > > > > > Please help me to solve this issue.
>> > > > > > And also I want to create my own driver using nuttx rtos on a
>> > > > > Nucleo-H73ZI2
>> > > > > > board . How to create our own driver and which IDE we have to
>> use?
>> > > > > >
>> > > > > > Please help me.
>> > > > > >
>> > > > > >
>> > > > > >
>> > > > > > Thanks & Regards,
>> > > > > > Rushikesh Ghatkar
>> > > > > >
>> > > > >
>> > > >
>> > >
>> >
>>
>

Reply via email to