Hi,

Your nuttx.bin is probably different than the nuttx.bin file which I sent to 
you that's why I configured and compiled an sent to you a new one for your 
sake; If you still can't get  the nsh> prompt with the firmware I sent to you I 
don't have any more answer for you. Maybe someone else can contribute.

Good luck.

From: rushi ghatkar <rushighatka...@gmail.com>
Sent: Tuesday, August 10, 2021 12:24 PM
To: dev@nuttx.apache.org
Subject: Re: Nuttx RTOS with Nucleo-H743ZI2 board



On Tue, Aug 10, 2021 at 2:52 PM rushi ghatkar 
<rushighatka...@gmail.com<mailto:rushighatka...@gmail.com>> wrote:
Hi Sir,

Thanks for your reply. Really appreciate it.

When i configured and compiled nuttx rtos then in my system nuttx.bin file was 
created. And I have flashed that file also. Please find the nuttx directory 
image attachment.

Your firmware file, nuttx bin file I have flashed successfully using 
STM32CubeProgramer.

But the issue is,
1. picocom or minicom is not working.
2. I want to create my own driver like PWM, ADC and for other peripherals, for 
this where I should start to create? and how?


Thanks & Regards,
Rushikesh Ghatkar




On Tue, Aug 10, 2021 at 2:33 PM Murat Tologlu 
<mtolo...@hotmail.com<mailto:mtolo...@hotmail.com>> wrote:
Hi Rushikesh,

Flash and try attached firmware ( you may try bin and hex files ) and tell us 
what happens.

Good luck,
Murat

From: rushi ghatkar <rushighatka...@gmail.com<mailto:rushighatka...@gmail.com>>
Sent: Tuesday, August 10, 2021 9:42 AM
To: dev@nuttx.apache.org<mailto:dev@nuttx.apache.org>
Subject: Re: Nuttx RTOS with Nucleo-H743ZI2 board

Hi,

Thanks for your reply.

I have followed this youtube video from Nuttx Channel,
https://www.youtube.com/watch?v=heSkSd-_70g&list=PLd73yQk5Fd8JEsVD-lhwYRQKVu6glfDa8&index=1

From the above link I have followed each step exactly as it is.

I'm using Nucleo-H743ZI2 board which has stlink-v3, for this in the end I was 
trying to execute command "openocd -f interface/stlink-v3.cfg -f 
target/stm32h7x.cfg" but this gives error. Please find the error image 
attachment.
As you asked, use STM32CubeProgrammer to flash nuttx.bin into the 
Nucleo-H743ZI2 board. And I used it and the nuttx.bin file has been flashed 
successfully.

After all this I was trying to open the nutshell using picocom, but nothing 
happened. No nutshell prompt appeared.

Please help me to solve this issue.


Thanks & Regards,
Rushikesh Ghatkar


On Tue, Aug 10, 2021 at 11:39 AM murat tologlu 
<mtolo...@hotmail.com<mailto:mtolo...@hotmail.com>> wrote:
Hi Rushikesh,

If you copy paste and share in a file attachment all the command line content 
from "$ cd nuttxspace/nuttx" to the end - not only picocom output " but 
everything that you did to configure and compile fooling "a video" ( which 
video? ) , perhaps we help can you.

Regards,
Murat

On 2021/08/10 05:00:36, rushi ghatkar 
<rushighatka...@gmail.com<mailto:rushighatka...@gmail.com>> wrote:
> Hi,
>
> I have followed a youtube video from Nuttx Channel to configure and compile
> Nuttx rtos with Nucleo-H743ZI2. And with the help of STM32CUbeProgrammer I
> have also flashed the nuttx.bin file into the board.
> But when I was trying to use minicom or picocom, I'm unable to use it.
> After executing this command "*sudo picocom /dev/ttyACM0 -b 115200" *,
> nutshell prompt is not appearing, please find the attachment.
> Need help for this.
>
>
> Regards,
> Rushikesh Ghatkar
>
> On Mon, Aug 9, 2021 at 8:17 PM murat tologlu 
> <mtolo...@hotmail.com<mailto:mtolo...@hotmail.com>> wrote:
>
> > Hi Rushi,
> >
> > Unless we know what you are trying to do we can't help you. There may be a
> > mistake anywhere!
> >
> > Explain what did you try so far, how ? Give us the links of the
> > application you're trying.. So may be we can discover your mistake.
> >
> > Regards,
> > Murat
> >
> > On 2021/08/09 04:36:22, rushi ghatkar 
> > <rushighatka...@gmail.com<mailto:rushighatka...@gmail.com>> wrote:
> > > Hi,
> > >
> > > I'm totally new to NUttx RTOS and I have started to work on it. I have a
> > > Nucleo-H743ZI2 board and followed a youtube video of Nuttx channel to
> > > configure, compile and flash Nuttx rtos in Nucleo-H743ZI2 board. After
> > > compilation nuttx.bin file has been created but to flash that on board,
> > > flash command is not working so I tried STM32CubeProgrammer to flash and
> > it
> > > got flash successfully.
> > > But after that "sudo picocom/dev/ttyACM0 -b 115200" , after executing and
> > > resetting the board  it's just waiting but the nsh> prompt isn't
> > appearing.
> > > What to do about it?
> > >
> > > Is there anyone who has worked on Nuttx RTOS with Nucleo-H743ZI2 board
> > and
> > > can help me with this issue?
> > > Please help me to solve this issue.
> > > And also I want to create my own driver using nuttx rtos on a
> > Nucleo-H73ZI2
> > > board . How to create our own driver and which IDE we have to use?
> > >
> > > Please help me.
> > >
> > >
> > >
> > > Thanks & Regards,
> > > Rushikesh Ghatkar
> > >
> >
>

Reply via email to