I have the same hatch over the head on my boat. Andy C&C 40 Peregrine
Andrew Burton 61 W Narragansett Newport, RI USA 02840 http://sites.google.com/site/andrewburtonyachtservices/ +401 965-5260 > On Dec 6, 2015, at 18:59, D Harben via CnC-List <cnc-list@cnc-list.com> wrote: > > Is the head hatch on the 70s Viking 33/34 the same? The Nicro 3" cap gives > some sense of scale in the picture: > > Viking 34 Head Hatch > > > Don > > V34 > NCYC > >> On Dec 6, 2015, at 6:17 PM, s/v Johanna Rose via CnC-List >> <cnc-list@cnc-list.com> wrote: >> >> Fred, >> >> All of my hinges have one hole. The break occurred between the hole and >> the hinge joint. I have posted additional photos on my blog but no write up >> yet. >> >> I checked Wally’s site(our hulls are two numbers off), and it looks like his >> hinges are like mine with one big hole through the acrylic for each hinge. >> The latch on the other hand has two holes. >> >> Maybe around 1981, they changed the hinge? >> >> >> Here is the direct link to Wally’s page: >> http://www.wbryant.com/StellaBoat/Projects/deck/hatch/index.htm >> >> >> Thanks again for you input. >> >> - >> Paul E. >> 1981 C&C 38 Landfall >> S/V Johanna Rose >> Carrabelle, FL >> >> http://svjohannarose.blogspot.com/ >> >>> On Dec 6, 2015, at 2:11 PM, cnc-list-requ...@cnc-list.com wrote: >>> >>> Date: Sun, 6 Dec 2015 13:07:50 -0600 >>> From: Frederick G Street <f...@postaudio.net> >>> To: cnc-list@cnc-list.com >>> Cc: PME <dre...@gmail.com> >>> Subject: Re: Stus-List little A&H hatches on a LF38 >>> Message-ID: <5296fd50-e2c9-41f5-bd42-89088414f...@postaudio.net> >>> Content-Type: text/plain; charset="utf-8" >>> >>> Paul ? that looks pretty nasty; and those lenses don?t look like they?re >>> original to me. The hinges have two holes for bolts; it looks like the one >>> on the left of your photo cracked across those two holes. I have no clue >>> where the other one came from, with one large bolt through it, unless it >>> was drilled out from its original state. >>> >>> If you can get the hinge pin out, I?d be willing to bet you could use the >>> one intact hinge from this hatch to have some new one machined out of >>> aluminum, with the original hole pattern for the lens bolts. If you decide >>> to go that route, let me know and I can have some lenses made up for you. >>> >>> I doubt you?re going to find a replacement hatch anywhere that will fit >>> those dimensions without having to do a LOT of glass work; the pads in >>> which they sit don?t match any after-market hatches I?ve ever been able to >>> find, or I would have replaced mine long ago. >>> >>> ? Fred >>> >>> Fred Street -- Minneapolis >>> S/V Oceanis (1979 C&C Landfall 38) -- on the hard in Bayfield, WI :^( >> >> _______________________________________________ >> >> Email address: >> CnC-List@cnc-list.com >> To change your list preferences, including unsubscribing -- go to the bottom >> of page at: >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the bottom > of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >
_______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
