I needed a line stripper for a Barient 24ST...looked all over the world for a year. I broke down and called Allen Hutton in AUS. They have just about any spare Barient part you could imagine...except a line stripper for a 24 ST! So...he made one...perfect replacement, very pleasant to work with. As for self tailers, look at Winchmate. When it makes it to the top of my priority list, I'm buying a pair for my 32 primaries.
Harry MIRAGE Northeast 39 Newport, RI Sent from my iPhone > On Feb 21, 2015, at 09:03, Bradley Lumgair via CnC-List > <cnc-list@cnc-list.com> wrote: > > Was at Toronto Boat Show, just realized I did pick up a catalogue for > Garhauer, nice stuff as I recall. will check them out further. > The plan in my little head right now is to 1) change out the halyards for all > synthetic, 2) try to pull new wire from the top of the mast and rig new > instruments, the old don't work anyways so I'm not losing anything even if > I'm unsuccessful, 3) check bushings/trade out sheaves after the mast comes > down in the fall. > Theres a lot of talk about self tailing winches, aftermarket or original > equipment? Eight Barient winches on ours, none are self tailing and all need > servicing, I see West Marine sells springs and pawls, I should get a couple > of sets for the inevitable loss, if needed I should be able to pick up > bearings at a local bearing shop? > Thank you for all your advise and suggestions > Brad > > Sent, miraculously through cyberspace, > from my iPad! > >> On Feb 21, 2015, at 04:28, cnc-list-requ...@cnc-list.com wrote: >> >> Send CnC-List mailing list submissions to >> cnc-list@cnc-list.com >> >> To subscribe or unsubscribe via the World Wide Web, visit >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >> or, via email, send a message with subject or body 'help' to >> cnc-list-requ...@cnc-list.com >> >> You can reach the person managing the list at >> cnc-list-ow...@cnc-list.com >> >> When replying, please edit your Subject line so it is more specific >> than "Re: Contents of CnC-List digest..." >> Today's Topics: >> >> 1. Re: C&C 33 MKII (Gary Nylander) >> 2. Re: C&C 33 MKII > Barient 24ST (Nauset Beach) >> 3. Re: C&C 33 MKII (Marek Dziedzic) >> 4. Refilling 10 lb propane tank (mike amirault) >> 5. Re: Refilling 10 lb propane tank (Josh Muckley) >> 6. salt water siphoning into sink (mike amirault) >> 7. Re: salt water siphoning into sink (Joel Aronson) >> 8. Re: salt water siphoning into sink (Mike Brannon) >> 9. Re: salt water siphoning into sink (Ken Heaton) >> 10. Re: salt water siphoning into sink (Jack Fitzgerald) >> 11. Re: salt water siphoning into sink (Bruno Lachance) >> 12. Re: salt water siphoning into sink (Graham Collins) >> 13. Re: Refilling 10 lb propane tank (Graham Collins) >> 14. Re: salt water siphoning into sink (Dennis C.) >> 15. Re: salt water siphoning into sink (Andrew Burton) >> 16. Re: salt water siphoning into sink (Russ & Melody) >> 17. Re: salt water siphoning into sink (dwight veinot) >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> <mime-attachment> >> _______________________________________________ >> CnC-List mailing list >> CnC-List@cnc-list.com >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the bottom > of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > _______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com