Brad,

We had a lot of winches on Perception when we bought her needing servicing. I 
took them all off one fall, brought them home and thoroughly cleaned all the 
old grease out of them - many hours of soaking in Mineral spirits, and using a 
stiff brush. All were fine after, and worked great! Subsequently I have reduced 
the number of winches, and changed 2 to Andersons, as we have migrated to 
cruising.

Where are you keeping your boat ?

Paul Fountain
Managing Director
SeaSource Inc.
Bookkeeping & IT Services.

-----Original Message-----
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Bradley 
Lumgair via CnC-List
Sent: Saturday, February 21, 2015 9:04 AM
To: cnc-list@cnc-list.com
Subject: Re: Stus-List CnC-List C&C 33 MKII

Was at Toronto Boat Show, just realized I did pick up a catalogue for Garhauer, 
nice stuff as I recall. will check them out further.
The plan in my little head right now is to 1) change out the halyards for all 
synthetic, 2) try to pull new wire from the top of the mast and rig new 
instruments, the old don't work anyways so I'm not losing anything even if I'm 
unsuccessful, 3) check bushings/trade out sheaves after the mast comes down in 
the fall. 
Theres a lot of talk about self tailing winches, aftermarket or original 
equipment? Eight Barient winches on ours, none are self tailing and all need 
servicing, I see West Marine sells springs and pawls, I should get a couple of 
sets for the inevitable loss, if needed I should be able to pick up bearings at 
a local bearing shop?
Thank you for all your advise and suggestions Brad

Sent, miraculously through cyberspace,
from my iPad!

> On Feb 21, 2015, at 04:28, cnc-list-requ...@cnc-list.com wrote:
> 
> Send CnC-List mailing list submissions to
>    cnc-list@cnc-list.com
> 
> To subscribe or unsubscribe via the World Wide Web, visit
>    http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
> or, via email, send a message with subject or body 'help' to
>    cnc-list-requ...@cnc-list.com
> 
> You can reach the person managing the list at
>    cnc-list-ow...@cnc-list.com
> 
> When replying, please edit your Subject line so it is more specific 
> than "Re: Contents of CnC-List digest..."
> Today's Topics:
> 
>   1. Re:  C&C 33 MKII (Gary Nylander)
>   2. Re:  C&C 33 MKII > Barient 24ST (Nauset Beach)
>   3. Re:  C&C 33 MKII (Marek Dziedzic)
>   4.  Refilling 10 lb propane tank (mike amirault)
>   5. Re:  Refilling 10 lb propane tank (Josh Muckley)
>   6.  salt water siphoning into sink (mike amirault)
>   7. Re:  salt water siphoning into sink (Joel Aronson)
>   8. Re:  salt water siphoning into sink (Mike Brannon)
>   9. Re:  salt water siphoning into sink (Ken Heaton)  10. Re:  salt 
> water siphoning into sink (Jack Fitzgerald)  11. Re:  salt water 
> siphoning into sink (Bruno Lachance)  12. Re:  salt water siphoning 
> into sink (Graham Collins)  13. Re:  Refilling 10 lb propane tank 
> (Graham Collins)  14. Re:  salt water siphoning into sink (Dennis C.)  
> 15. Re:  salt water siphoning into sink (Andrew Burton)  16. Re:  salt 
> water siphoning into sink (Russ & Melody)  17. Re:  salt water 
> siphoning into sink (dwight veinot) <mime-attachment> 
> <mime-attachment> <mime-attachment> <mime-attachment> 
> <mime-attachment> <mime-attachment> <mime-attachment> 
> <mime-attachment> <mime-attachment> <mime-attachment> 
> <mime-attachment> <mime-attachment> <mime-attachment> 
> <mime-attachment> <mime-attachment> <mime-attachment> 
> <mime-attachment> _______________________________________________
> CnC-List mailing list
> CnC-List@cnc-list.com
> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com

_______________________________________________

Email address:
CnC-List@cnc-list.com
To change your list preferences, including unsubscribing -- go to the bottom of 
page at:
http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com


_______________________________________________

Email address:
CnC-List@cnc-list.com
To change your list preferences, including unsubscribing -- go to the bottom of 
page at:
http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com

Reply via email to