I’ve had a squeeze bulb on my 4JH engine for 7 years. The bulb is still perfect. It makes filling the filter after a change a snap and easy to bleed the air out of the system.
Fred Hazzard S/V Fury C&C 44 Portland, OR From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of bria...@aol.com Sent: Thursday, June 06, 2013 7:17 PM To: cnc-list@cnc-list.com Subject: Re: Stus-List electric boost pump for YANMAR diesel I plan on installing a low pressure electric pump on my YANMAR 4JH engine. What is the best way to power it? To the "ignition/starter" switch, or a separate switch? It is a "free flow" so it can be left OFF and fuel will pass through it. I don't plan to use it all of the time, just to bleed the system. How have others done it? Thanks Bill MYSTY Landfall 39 In a message dated 6/6/2013 2:21:10 P.M. Eastern Daylight Time, ind...@thethomsons.us writes: Good advice – been there – done that. Ended up having to crack each of the injectors to bleed the darn thing. Why isn’t the Yanmar self-bleeding like other engines. To think of it, why does it not have an integral pump to aid changing the oil too. Jonathan Indigo 35/3 – Southport CT _____ From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of David Risch Sent: Thursday, June 06, 2013 11:11 AM To: CNC CNC Subject: Re: Stus-List fuel filter change Jim, Love the fact that you you are learning to work on your engine and as you are finding out you have a wealth of information available to you here on the list. One word of caution (first hand experience talking here) after you play with the fuel system make sure you have all the air out of it. The dang thing may crap out at the most inopportune time with just a wee bit of air. Run it in gear under load for a bit and listen to it. It is fairly obvious if it is happy. David F. Risch (401) 419-4650 (cell) _____ From: dreamsai...@live.ca To: cnc-list@cnc-list.com Date: Thu, 6 Jun 2013 08:37:20 -0500 Subject: Re: Stus-List fuel filter change Thankyou!!!! Jim _____ From: pete.shelqu...@comcast.net To: cnc-list@cnc-list.com Date: Wed, 5 Jun 2013 21:59:57 -0500 Subject: Re: Stus-List fuel filter change FYI - The last little press of the flipper is where the actual pumping happens. If this is really short, the pump is probably on the lobe of the cam. Turn the engine over a bit to get on the flat part. Hope that makes sense. From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Josh Muckley Sent: Wednesday, June 05, 2013 9:35 PM To: cnc-list@cnc-list.com Subject: Re: Stus-List fuel filter change Shut the fuel off. Unscrew the cup. Pull out the filter. Insert a new one. Fill the cup with new fuel. Screw the cup back on. Open the vent. Pump the priming/lift pump lever until the filter cup is fully vented. In case you don't know, the lift pump is on the right side of the engine, about halfway down and one third of the way forward of the flywheel. It will be the first thing on the engine that the fuel flows into. The filter is next in line moving forward. The lift pump should have a little flipper that you can push up and down to manually prime the system. Josh Muckley S/V Sea Hawk 1989 C&C 37+ Yanmar 3HM35F -- When security matters. http://www.secure-my-email.com <http://www.secure-my-email.com/> On Jun 5, 2013 10:19 PM, "Jim Bradley" <dreamsai...@live.ca> wrote: How do you change the fuel filter on a yanmar 3gm Jim Bradley Allegro Andante Barrie Ontario _______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com <http://www.cncphotoalbum.com/> CnC-List@cnc-list.com _______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com _______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com _______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
_______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
