Thanks again. This will help alot.
On 5/10/13, dwight veinot <dwightvei...@hfx.eastlink.ca> wrote: > The manual for the st 4000 is on that site as well > > Dwight Veinot > C&C 35 MKII, Alianna > Head of St. Margaret's Bay, NS > > > -----Original Message----- > From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Curtis > Sent: May 10, 2013 10:18 AM > To: cnc-list@cnc-list.com > Subject: Re: Stus-List ST4000 Fluxgate dile in > > This helps a great deal. > > > It always helps to have a manule. However my control head dont look > like this one? > > > > > > On 5/10/13, dwight veinot <dwightvei...@hfx.eastlink.ca> wrote: >> Curtis >> >> Check here for the manual you need: >> >> http://www.raymarine.com/view/?id=1836 >> >> or see page 83 in the st 4000+ manual >> >> Dwight Veinot >> C&C 35 MKII, Alianna >> Head of St. Margaret's Bay, NS >> >> Dwight Veinot >> C&C 35 MKII, Alianna >> Head of St. Margaret's Bay, NS >> >> >> -----Original Message----- >> From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Curtis >> Sent: May 10, 2013 8:31 AM >> To: cnc-list@cnc-list.com >> Subject: Re: Stus-List ST4000 Fluxgate dile in >> >> Thanks will clean the wires and hook them back up. Do you know where I >> can get the proceedures on how to do the circle thing? >> >> On 5/10/13, dwight veinot <dwightvei...@hfx.eastlink.ca> wrote: >>> Curtis >>> >>> I believe what you are describing as "dial in" is called a deviation >>> check >>> on the fluxgate compass. You need to do very slow circles (counter >>> clockwise works for me) and if you go too fast that will be displayed >>> and >>> you will have to start again. Usually after about 1 complete circle you >>> should see a compass deviation number, anything 3 degrees and below is >>> good. >>> You can also adjust the heading angle to be the same as that indicated >>> by >>> your chart plotter or magnetic compass if you know it to be correct and >>> your >>> fluxgate compass reading is significantly different. I have discovered >>> that >>> sometimes the fluxgate compass may give very erroneous indications if >>> the >>> boat is not moving forward. Make sure all 5 wires from the fluxgate >>> compass >>> are making good electrical contact at the spade connectors on the >>> control >>> head...take them off and reestablish a connection and use some >>> electrical >>> contact cleaner on the connections to improve things. >>> >>> Dwight Veinot >>> C&C 35 MKII, Alianna >>> Head of St. Margaret's Bay, NS >>> >>> >>> -----Original Message----- >>> From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of >>> Curtis >>> Sent: May 10, 2013 8:05 AM >>> To: CnC-List@cnc-list.com >>> Subject: Stus-List ST4000 Fluxgate dile in >>> >>> Can I dile in the fluxgate compass usint the control head for the >>> st4000? >>> Or what is the the 3 circle procedure for this process? It is the >>> first time I have tried to use the auto helm st4000. When I put it on >>> auto, it holds the course just fine its just reading like 209 degrees >>> when the boat is tied up at the dock at like meg 340 degrees? >>> Can I do a large dile in and then swing the the boat for deveation?> >>> >>> -- >>> "The pessimist complains about the wind; the optimist expects it to >>> change; the realist adjusts the sails." >>> >>> _______________________________________________ >>> This List is provided by the C&C Photo Album >>> http://www.cncphotoalbum.com >>> CnC-List@cnc-list.com >>> ----- >>> No virus found in this message. >>> Checked by AVG - www.avg.com >>> Version: 2012.0.2241 / Virus Database: 3162/5810 - Release Date: >>> 05/09/13 >>> >>> >>> _______________________________________________ >>> This List is provided by the C&C Photo Album >>> http://www.cncphotoalbum.com >>> CnC-List@cnc-list.com >>> >> >> >> -- >> "The pessimist complains about the wind; the optimist expects it to >> change; the realist adjusts the sails." >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> http://www.cncphotoalbum.com >> CnC-List@cnc-list.com >> ----- >> No virus found in this message. >> Checked by AVG - www.avg.com >> Version: 2012.0.2241 / Virus Database: 3162/5810 - Release Date: 05/09/13 >> >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> http://www.cncphotoalbum.com >> CnC-List@cnc-list.com >> > > > -- > "The pessimist complains about the wind; the optimist expects it to > change; the realist adjusts the sails." > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com > > ----- > No virus found in this message. > Checked by AVG - www.avg.com > Version: 2012.0.2241 / Virus Database: 3162/5813 - Release Date: 05/10/13 > > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com > -- “The pessimist complains about the wind; the optimist expects it to change; the realist adjusts the sails.” _______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
