Hi, thanks Darren and Paul. Do you have experience with 15.0 on the cat6k platform? Is it advisable to upgrade from 12.2 to 15.x?
Thanks, Robert On 27.07.2013 20:51, Paul Wells wrote: > Hi Robert, > > Everything Darren says is correct. However, in your example below you > also removed: > > ipv6 ospf 12345 area 0 > > You will still need to enable OSPFv3 (ipv6 ospf) under the interface in > 12.2(33)SXJ. OSPFv3 doesn't have a "network" command. > > For a more comprehensive list of which releases support the OSPFv2 > interface enable command you can use feature navigator. Search for the > following feature names: > > Area Command in Interface Mode for OSPFv2 > Enabling OSPFv2 on an Interface Using the ip ospf area Command > > Note: both names refer to the same feature, though in different trains. > The command is available on the cat6k starting with 15.0(SY). > > Regards, > Paul > > On 07/27/2013 10:52 AM, Darren O'Connor wrote: >> Yes. >> >> In your first config you are enabling ospf under the interface, under the >> process, and you're also redistributing that same interface subnet under >> ospf by using redistribute connected. You don't need both the interface >> config and the process config. It doesn't break anything using both, but it >> makes it difficult for others to troubleshoot later. If you did use both, >> the most specific will 'win' >> >> And yes, while your release is 'new', the train itself is old. Check here: >> http://www.cisco.com/en/US/docs/ios-xml/ios/iproute_ospf/command/ospf-a1.html#wp1148191700 >> >> It shows which releases have this command enabled and when. The SX train is >> not on that list >> >> Thanks >> >> Darren >> >> http://www.mellowd.co.uk/ >> >> On 27 Jul 2013, at 16:41, "Robert" <[email protected]> wrote: >> >>> Hi, >>> >>> older release? Just take a look, 12.2(33) was compiled in April 2012. >>> Until now I've had no problems to enable OSPF on the interface _and_ in >>> router ospf section of the config. (12.4 and 12.5 train for VXR chassis) >>> >>> >>> Do you mean this config is enough: >>> >>> ! >>> router ospf 12345 >>> router-id 192.168.100.232 >>> redistribute connected subnets >>> redistribute static >>> passive-interface default >>> no passive-interface Vlan50 >>> network 192.168.100.0 0.0.15.255 area 0 >>> ! >>> ipv6 router ospf 12345 >>> router-id 192.168.100.232 >>> log-adjacency-changes >>> passive-interface default >>> no passive-interface Vlan50 >>> redistribute connected >>> ! >>> ... >>> ... >>> ! >>> interface Vlan50 >>> ip address 192.168.100.197 255.255.255.252 >>> no ip redirects >>> no ip proxy-arp >>> ipv6 address x:x:x:x::y/126 >>> ipv6 nd ra suppress >>> ! >>> >>> Without enabling OSPF on interface side? >>> >>> >>> >>> Thanks, >>> >>> Robert >>> >>> >>> >>> >>> On 27.07.2013 17:25, Darren O'Connor wrote: >>>> The interface-level ospf command was not available in older releases. >>>> >>>> A bit odd to enable OSPf on an interface under both router ospf and the >>>> interface itself. I would stick to just one or the other >>>> >>>>> Date: Sat, 27 Jul 2013 15:43:52 +0200 >>>>> From: [email protected] >>>>> To: [email protected] >>>>> Subject: [c-nsp] OSPF question >>>>> >>>>> Hi, >>>>> >>>>> I'm a little bit confused while configuring a CAT6509 switch with OSPF. >>>>> So far, I used on the c7206-VXR platform the following config: >>>>> >>>>> ! >>>>> router ospf 12345 >>>>> router-id 192.168.100.232 >>>>> redistribute connected subnets >>>>> redistribute static >>>>> passive-interface default >>>>> no passive-interface GigabitEthernet0/1.50 >>>>> network 192.168.100.0 0.0.15.255 area 0 >>>>> ! >>>>> ... >>>>> ... >>>>> ! >>>>> interface GigabitEthernet0/1.50 >>>>> encapsulation dot1Q 556 >>>>> ip address 192.168.100.197 255.255.255.252 >>>>> no ip redirects >>>>> no ip proxy-arp >>>>> ip ospf 12345 area 0 >>>>> ipv6 address 2001:5DD:50::1/126 >>>>> ipv6 nd ra suppress >>>>> ipv6 ospf 12345 area 0 >>>>> ! >>>>> >>>>> Now, with IOS "s72033-advipservicesk9_wan-mz.122-33.SXJ3" the statement >>>>> "ip ospf <process-ID> area 0" is missing. >>>>> >>>>> ! >>>>> interface GigabitEthernet4/21 >>>>> switchport >>>>> switchport trunk encapsulation dot1q >>>>> switchport mode trunk >>>>> switchport trunk allowed vlan 50 >>>>> no cdp enable >>>>> ! >>>>> ... >>>>> ... >>>>> ! >>>>> interface Vlan50 >>>>> ip address 192.168.100.197 255.255.255.252 >>>>> no ip redirects >>>>> no ip proxy-arp >>>>> ipv6 address x:x:x:x::y/126 >>>>> ipv6 nd ra suppress >>>>> ipv6 ospf 12345 area 0 >>>>> ! >>>>> >>>>> The "ip ospf area 0" command is unrecognized :-( Any ideas? >>>>> >>>>> >>>>> >>>>> Regards, >>>>> >>>>> Robert >>>>> _______________________________________________ >>>>> cisco-nsp mailing list [email protected] >>>>> https://puck.nether.net/mailman/listinfo/cisco-nsp >>>>> archive at http://puck.nether.net/pipermail/cisco-nsp/ >>>> >>>> _______________________________________________ >>>> cisco-nsp mailing list [email protected] >>>> https://puck.nether.net/mailman/listinfo/cisco-nsp >>>> archive at http://puck.nether.net/pipermail/cisco-nsp/ >>> >> _______________________________________________ >> cisco-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ >> > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
