Hi, older release? Just take a look, 12.2(33) was compiled in April 2012. Until now I've had no problems to enable OSPF on the interface _and_ in router ospf section of the config. (12.4 and 12.5 train for VXR chassis)
Do you mean this config is enough: ! router ospf 12345 router-id 192.168.100.232 redistribute connected subnets redistribute static passive-interface default no passive-interface Vlan50 network 192.168.100.0 0.0.15.255 area 0 ! ipv6 router ospf 12345 router-id 192.168.100.232 log-adjacency-changes passive-interface default no passive-interface Vlan50 redistribute connected ! ... ... ! interface Vlan50 ip address 192.168.100.197 255.255.255.252 no ip redirects no ip proxy-arp ipv6 address x:x:x:x::y/126 ipv6 nd ra suppress ! Without enabling OSPF on interface side? Thanks, Robert On 27.07.2013 17:25, Darren O'Connor wrote: > The interface-level ospf command was not available in older releases. > > A bit odd to enable OSPf on an interface under both router ospf and the > interface itself. I would stick to just one or the other > >> Date: Sat, 27 Jul 2013 15:43:52 +0200 >> From: [email protected] >> To: [email protected] >> Subject: [c-nsp] OSPF question >> >> Hi, >> >> I'm a little bit confused while configuring a CAT6509 switch with OSPF. >> So far, I used on the c7206-VXR platform the following config: >> >> ! >> router ospf 12345 >> router-id 192.168.100.232 >> redistribute connected subnets >> redistribute static >> passive-interface default >> no passive-interface GigabitEthernet0/1.50 >> network 192.168.100.0 0.0.15.255 area 0 >> ! >> ... >> ... >> ! >> interface GigabitEthernet0/1.50 >> encapsulation dot1Q 556 >> ip address 192.168.100.197 255.255.255.252 >> no ip redirects >> no ip proxy-arp >> ip ospf 12345 area 0 >> ipv6 address 2001:5DD:50::1/126 >> ipv6 nd ra suppress >> ipv6 ospf 12345 area 0 >> ! >> >> Now, with IOS "s72033-advipservicesk9_wan-mz.122-33.SXJ3" the statement >> "ip ospf <process-ID> area 0" is missing. >> >> ! >> interface GigabitEthernet4/21 >> switchport >> switchport trunk encapsulation dot1q >> switchport mode trunk >> switchport trunk allowed vlan 50 >> no cdp enable >> ! >> ... >> ... >> ! >> interface Vlan50 >> ip address 192.168.100.197 255.255.255.252 >> no ip redirects >> no ip proxy-arp >> ipv6 address x:x:x:x::y/126 >> ipv6 nd ra suppress >> ipv6 ospf 12345 area 0 >> ! >> >> The "ip ospf area 0" command is unrecognized :-( Any ideas? >> >> >> >> Regards, >> >> Robert >> _______________________________________________ >> cisco-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
