On Fri, Sep 16, 2016 at 08:35:30AM +1000, Jonathan Gray wrote: > On Tue, Aug 23, 2016 at 10:42:07AM +0900, Tuyosi T wrote: > > hi all . > > > > panda's arm openbsd is fragile at present . > > > > so i tried panda's arm freebsd . > > it is easy to install . > > but then after there is no package. > > so i install even lftp by ports . > > many minites is costed . > > and perhaps i cannot gain X . > > panda's arm freebsd is convinient to diagnose panda's helthy . > > > > panda runs arch linux , but odroid-c2 runs it more better . > > > > anyway i heartly wait the day panda runs openbsd well . > > abieber@ lent me his pandaboard and I've managed to get > it working again by adding the omwugen(4) driver. > > This should be available in snapshots in a few days time.
Woo - thanks jsg! > > OpenBSD 6.0-current (GENERIC) #41: Fri Sep 16 08:20:30 AEST 2016 > j...@imx.jsg.id.au:/sys/arch/armv7/compile/GENERIC > real mem = 1073741824 (1024MB) > avail mem = 1044398080 (996MB) > mainbus0 at root: TI OMAP4 PandaBoard-ES > cpu0 at mainbus0: ARM Cortex A9 R2 rev 10 (ARMv7 core) > cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled > cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache > cortex0 at mainbus0 > amptimer0 at cortex0: tick rate 396000 KHz > armliicc0 at cortex0: rtl 7 waymask: 0x0000000f > omap0 at mainbus0 > omapid0 at omap0: omap4460 > amptimer0: adjusting clock: new tick rate 350000 KHz > prcm0 at omap0 rev 0.0 > ampintc0 at mainbus0 nirq 160 > omwugen0 at mainbus0 > simplebus0 at mainbus0: "ocp" > simplebus1 at simplebus0: "l4" > simplebus2 at simplebus1: "scm" > simplebus3 at simplebus1: "scm" > simplebus4 at simplebus3: "omap4_padconf_global" > simplebus5 at simplebus1: "l4" > omgpio0 at simplebus0: rev 0.1 > gpio0 at omgpio0: 32 pins > omgpio1 at simplebus0: rev 0.1 > gpio1 at omgpio1: 32 pins > omgpio2 at simplebus0: rev 0.1 > gpio2 at omgpio2: 32 pins > omgpio3 at simplebus0: rev 0.1 > gpio3 at omgpio3: 32 pins > omgpio4 at simplebus0: rev 0.1 > gpio4 at omgpio4: 32 pins > omgpio5 at simplebus0: rev 0.1 > gpio5 at omgpio5: 32 pins > com0 at simplebus0: ti16750, 64 byte fifo > com0: probed fifo depth: 0 bytes > com1 at simplebus0: ti16750, 64 byte fifo > com1: probed fifo depth: 0 bytes > com2 at simplebus0: ti16750, 64 byte fifo > com2: console > com3 at simplebus0: ti16750, 64 byte fifo > com3: probed fifo depth: 0 bytes > tiiic0 at simplebus0 rev 0.11 > iic0 at tiiic0 > "ti,twl6030" at iic0 addr 0x48 not configured > "ti,twl6040" at iic0 addr 0x4b not configured > tiiic1 at simplebus0 rev 0.11 > iic1 at tiiic1 > tiiic2 at simplebus0 rev 0.11 > iic2 at tiiic2 > "ti,eeprom" at iic2 addr 0x50 not configured > tiiic3 at simplebus0 rev 0.11 > iic3 at tiiic3 > ommmc0 at simplebus0 > sdmmc0 at ommmc0: 1-bit, mmc high-speed > ommmc1 at simplebus0 > sdmmc1 at ommmc1: 1-bit > omdog0 at simplebus0 rev 0.1 > omehci0 at simplebus0 > usb0 at omehci0: USB revision 2.0 > uhub0 at usb0 configuration 1 interface 0 "TI OMAP EHCI root hub" rev > 2.00/1.00 addr 1 > sdmmc1: can't supply clock > sdmmc1: can't enable card > scsibus0 at sdmmc0: 2 targets, initiator 0 > sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SP16G, 0080> SCSI2 0/direct fixed > sd0: 15193MB, 512 bytes/sector, 31116288 sectors > uhub1 at uhub0 port 1 configuration 1 interface 0 "Standard Microsystems > product 0x9514" rev 2.00/2.00 addr 2 > smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems > SMSC9512/14" rev 2.00/2.00 addr 3 > smsc0: address ff:ff:ff:ff:ff:ff > ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x0001f0, model 0x000c > vscsi0 at root > scsibus1 at vscsi0: 256 targets > softraid0 at root > scsibus2 at softraid0: 256 targets > boot device: sd0 > root on sd0a (598f77489bf4631c.a) swap on sd0b dump on sd0b > WARNING: CHECK AND RESET THE DATE!
