On Tue, Aug 23, 2016 at 10:42:07AM +0900, Tuyosi T wrote:
> hi all .
>
> panda's arm openbsd is fragile at present .
>
> so i tried panda's arm freebsd .
> it is easy to install .
> but then after there is no package.
> so i install even lftp by ports .
> many minites is costed .
> and perhaps i cannot gain X .
> panda's arm freebsd is convinient to diagnose panda's helthy .
>
> panda runs arch linux , but odroid-c2 runs it more better .
>
> anyway i heartly wait the day panda runs openbsd well .
abieber@ lent me his pandaboard and I've managed to get
it working again by adding the omwugen(4) driver.
This should be available in snapshots in a few days time.
OpenBSD 6.0-current (GENERIC) #41: Fri Sep 16 08:20:30 AEST 2016
j...@imx.jsg.id.au:/sys/arch/armv7/compile/GENERIC
real mem = 1073741824 (1024MB)
avail mem = 1044398080 (996MB)
mainbus0 at root: TI OMAP4 PandaBoard-ES
cpu0 at mainbus0: ARM Cortex A9 R2 rev 10 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 7 waymask: 0x0000000f
omap0 at mainbus0
omapid0 at omap0: omap4460
amptimer0: adjusting clock: new tick rate 350000 KHz
prcm0 at omap0 rev 0.0
ampintc0 at mainbus0 nirq 160
omwugen0 at mainbus0
simplebus0 at mainbus0: "ocp"
simplebus1 at simplebus0: "l4"
simplebus2 at simplebus1: "scm"
simplebus3 at simplebus1: "scm"
simplebus4 at simplebus3: "omap4_padconf_global"
simplebus5 at simplebus1: "l4"
omgpio0 at simplebus0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at simplebus0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at simplebus0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at simplebus0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at simplebus0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at simplebus0: rev 0.1
gpio5 at omgpio5: 32 pins
com0 at simplebus0: ti16750, 64 byte fifo
com0: probed fifo depth: 0 bytes
com1 at simplebus0: ti16750, 64 byte fifo
com1: probed fifo depth: 0 bytes
com2 at simplebus0: ti16750, 64 byte fifo
com2: console
com3 at simplebus0: ti16750, 64 byte fifo
com3: probed fifo depth: 0 bytes
tiiic0 at simplebus0 rev 0.11
iic0 at tiiic0
"ti,twl6030" at iic0 addr 0x48 not configured
"ti,twl6040" at iic0 addr 0x4b not configured
tiiic1 at simplebus0 rev 0.11
iic1 at tiiic1
tiiic2 at simplebus0 rev 0.11
iic2 at tiiic2
"ti,eeprom" at iic2 addr 0x50 not configured
tiiic3 at simplebus0 rev 0.11
iic3 at tiiic3
ommmc0 at simplebus0
sdmmc0 at ommmc0: 1-bit, mmc high-speed
ommmc1 at simplebus0
sdmmc1 at ommmc1: 1-bit
omdog0 at simplebus0 rev 0.1
omehci0 at simplebus0
usb0 at omehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "TI OMAP EHCI root hub" rev 2.00/1.00
addr 1
sdmmc1: can't supply clock
sdmmc1: can't enable card
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SP16G, 0080> SCSI2 0/direct fixed
sd0: 15193MB, 512 bytes/sector, 31116288 sectors
uhub1 at uhub0 port 1 configuration 1 interface 0 "Standard Microsystems
product 0x9514" rev 2.00/2.00 addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address ff:ff:ff:ff:ff:ff
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
boot device: sd0
root on sd0a (598f77489bf4631c.a) swap on sd0b dump on sd0b
WARNING: CHECK AND RESET THE DATE!
