hi all .
i previously failed 5.9 panda , but now i succeed in 5.9 .
this tells me tha the choice of sd card is very important .
now i use transcend premium 400X 16GB .
but with this card , i fail 5.9 panda .
5.9 panda's full story is the followings
-----------------------
cu -l cua00 -s 115200
Connected to /dev/cua00 (speed 115200)
U-Boot SPL 2015.10 (Feb 01 2016 - 13:59:48)
OMAP4430 ES2.2
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img
U-Boot 2015.10 (Feb 01 2016 - 13:59:48 +1100)
CPU : OMAP4430 ES2.2
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
reading uboot.env
** Unable to read "uboot.env" from mmc0:1 **
Using default environment
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
159 bytes read in 3 ms (51.8 KiB/s)
Importing environment from mmc0 ...
Running uenvcmd ...
reading bsd.umg
8032536 bytes read in 381 ms (20.1 MiB/s)
## Booting kernel from Legacy Image at 82800000 ...
Image Name: boot
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8032472 Bytes = 7.7 MiB
Load Address: 80300000
Entry Point: 80300000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
OpenBSD/omap booting ...
arg0 0x0 arg1 0xae7 arg2 0x80000100
atag core flags 0 pagesize 0 rootdev 0
atag cmdline [sd0i:/bsd.umg]
atag mem start 0x80000000 size 0x40000000
bootfile: sd0i:/bsd.umg
bootargs:
memory size derived from u-boot
bootconf.mem[0].address = 80000000 pages 262144/0x40000000
Allocating page tables
freestart = 0x80aaa000, free_pages = 259414 (0x0003f556)
IRQ stack: p0x80ad8000 v0xc0ad8000
ABT stack: p0x80ad9000 v0xc0ad9000
UND stack: p0x80ada000 v0xc0ada000
SVC stack: p0x80adb000 v0xc0adb000
Creating L1 page table at 0x80aac000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 2791
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights
reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 5.9 (RAMDISK) #43: Sat Feb 27 10:55:39 AEDT 2016
j...@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1041670144 (993MB)
mainbus0 at root
cortex0 at mainbus0
ampintc0 at cortex0 nirq 160
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 4 waymask: 0x0000000f
cpu0 at mainbus0: ARM Cortex A9 R1 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
omap0 at mainbus0: TI OMAP4 PandaBoard
omapid0 at omap0: omap4430
amptimer0: adjusting clock: new tick rate 400000 KHz
prcm0 at omap0 rev 0.0
omdog0 at omap0 rev 0.0
omgpio0 at omap0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at omap0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at omap0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at omap0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at omap0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at omap0: rev 0.1
gpio5 at omgpio5: 32 pins
ommmc0 at omap0
sdmmc0 at ommmc0
com0 at omap0: ti16750, 64 byte fifo
com0: console
ehci0 at omap0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "TI OMAP EHCI root hub" rev 2.00/1.00 addr 1
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd0: 15343MB, 512 bytes/sector, 31422464 sectors
uhub1 at uhub0 port 1 "Standard Microsystems product 0x9514" rev
2.00/2.00 addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address ff:ff:ff:ff:ff:ff
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
panic: pool_do_get: pvepl: page empty
syncing disks... done
rebooting...
U-Boot SPL 2015.10 (Feb 01 2016 - 13:59:48)
OMAP4430 ES2.2
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img
U-Boot 2015.10 (Feb 01 2016 - 13:59:48 +1100)
CPU : OMAP4430 ES2.2
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
reading uboot.env
** Unable to read "uboot.env" from mmc0:1 **
Using default environment
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
159 bytes read in 3 ms (51.8 KiB/s)
Importing environment from mmc0 ...
Running uenvcmd ...
reading bsd.umg
8032536 bytes read in 381 ms (20.1 MiB/s)
## Booting kernel from Legacy Image at 82800000 ...
Image Name: boot
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8032472 Bytes = 7.7 MiB
Load Address: 80300000
Entry Point: 80300000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
OpenBSD/omap booting ...
arg0 0x0 arg1 0xae7 arg2 0x80000100
atag core flags 0 pagesize 0 rootdev 0
atag cmdline [sd0i:/bsd.umg]
atag mem start 0x80000000 size 0x40000000
bootfile: sd0i:/bsd.umg
bootargs:
memory size derived from u-boot
bootconf.mem[0].address = 80000000 pages 262144/0x40000000
Allocating page tables
freestart = 0x80aaa000, free_pages = 259414 (0x0003f556)
IRQ stack: p0x80ad8000 v0xc0ad8000
ABT stack: p0x80ad9000 v0xc0ad9000
UND stack: p0x80ada000 v0xc0ada000
SVC stack: p0x80adb000 v0xc0adb000
Creating L1 page table at 0x80aac000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 2791
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights
reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 5.9 (RAMDISK) #43: Sat Feb 27 10:55:39 AEDT 2016
j...@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1041670144 (993MB)
mainbus0 at root
cortex0 at mainbus0
ampintc0 at cortex0 nirq 160
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 4 waymask: 0x0000000f
cpu0 at mainbus0: ARM Cortex A9 R1 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
omap0 at mainbus0: TI OMAP4 PandaBoard
omapid0 at omap0: omap4430
amptimer0: adjusting clock: new tick rate 400000 KHz
prcm0 at omap0 rev 0.0
omdog0 at omap0 rev 0.0
omgpio0 at omap0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at omap0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at omap0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at omap0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at omap0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at omap0: rev 0.1
gpio5 at omgpio5: 32 pins
ommmc0 at omap0
sdmmc0 at ommmc0
com0 at omap0: ti16750, 64 byte fifo
com0: console
ehci0 at omap0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "TI OMAP EHCI root hub" rev 2.00/1.00 addr 1
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd0: 15343MB, 512 bytes/sector, 31422464 sectors
uhub1 at uhub0 port 1 "Standard Microsystems product 0x9514" rev
2.00/2.00 addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address ff:ff:ff:ff:ff:ff
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/armv7 5.9 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? i
panic: pool_do_get: pvepl: page empty
syncing disks... done
rebooting...
U-Boot SPL 2015.10 (Feb 01 2016 - 13:59:48)
OMAP4430 ES2.2
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img
U-Boot 2015.10 (Feb 01 2016 - 13:59:48 +1100)
CPU : OMAP4430 ES2.2
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
reading uboot.env
** Unable to read "uboot.env" from mmc0:1 **
Using default environment
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
159 bytes read in 3 ms (51.8 KiB/s)
Importing environment from mmc0 ...
Running uenvcmd ...
reading bsd.umg
8032536 bytes read in 381 ms (20.1 MiB/s)
## Booting kernel from Legacy Image at 82800000 ...
Image Name: boot
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8032472 Bytes = 7.7 MiB
Load Address: 80300000
Entry Point: 80300000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
OpenBSD/omap booting ...
arg0 0x0 arg1 0xae7 arg2 0x80000100
atag core flags 0 pagesize 0 rootdev 0
atag cmdline [sd0i:/bsd.umg]
atag mem start 0x80000000 size 0x40000000
bootfile: sd0i:/bsd.umg
bootargs:
memory size derived from u-boot
bootconf.mem[0].address = 80000000 pages 262144/0x40000000
Allocating page tables
freestart = 0x80aaa000, free_pages = 259414 (0x0003f556)
IRQ stack: p0x80ad8000 v0xc0ad8000
ABT stack: p0x80ad9000 v0xc0ad9000
UND stack: p0x80ada000 v0xc0ada000
SVC stack: p0x80adb000 v0xc0adb000
Creating L1 page table at 0x80aac000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 2791
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights
reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 5.9 (RAMDISK) #43: Sat Feb 27 10:55:39 AEDT 2016
j...@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1041670144 (993MB)
mainbus0 at root
cortex0 at mainbus0
ampintc0 at cortex0 nirq 160
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 4 waymask: 0x0000000f
cpu0 at mainbus0: ARM Cortex A9 R1 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
omap0 at mainbus0: TI OMAP4 PandaBoard
omapid0 at omap0: omap4430
amptimer0: adjusting clock: new tick rate 400000 KHz
prcm0 at omap0 rev 0.0
omdog0 at omap0 rev 0.0
omgpio0 at omap0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at omap0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at omap0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at omap0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at omap0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at omap0: rev 0.1
gpio5 at omgpio5: 32 pins
ommmc0 at omap0
sdmmc0 at ommmc0
com0 at omap0: ti16750, 64 byte fifo
com0: console
ehci0 at omap0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "TI OMAP EHCI root hub" rev 2.00/1.00 addr 1
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd0: 15343MB, 512 bytes/sector, 31422464 sectors
uhub1 at uhub0 port 1 "Standard Microsystems product 0x9514" rev
2.00/2.00 addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address ff:ff:ff:ff:ff:ff
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
panic: pool_do_get: pvepl: page empty
syncing disks... done
rebooting...
U-Boot SPL 2015.10 (Feb 01 2016 - 13:59:48)
OMAP4430 ES2.2
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img
U-Boot 2015.10 (Feb 01 2016 - 13:59:48 +1100)
CPU : OMAP4430 ES2.2
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
reading uboot.env
** Unable to read "uboot.env" from mmc0:1 **
Using default environment
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
159 bytes read in 3 ms (51.8 KiB/s)
Importing environment from mmc0 ...
Running uenvcmd ...
reading bsd.umg
8032536 bytes read in 381 ms (20.1 MiB/s)
## Booting kernel from Legacy Image at 82800000 ...
Image Name: boot
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8032472 Bytes = 7.7 MiB
Load Address: 80300000
Entry Point: 80300000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
OpenBSD/omap booting ...
arg0 0x0 arg1 0xae7 arg2 0x80000100
atag core flags 0 pagesize 0 rootdev 0
atag cmdline [sd0i:/bsd.umg]
atag mem start 0x80000000 size 0x40000000
bootfile: sd0i:/bsd.umg
bootargs:
memory size derived from u-boot
bootconf.mem[0].address = 80000000 pages 262144/0x40000000
Allocating page tables
freestart = 0x80aaa000, free_pages = 259414 (0x0003f556)
IRQ stack: p0x80ad8000 v0xc0ad8000
ABT stack: p0x80ad9000 v0xc0ad9000
UND stack: p0x80ada000 v0xc0ada000
SVC stack: p0x80adb000 v0xc0adb000
Creating L1 page table at 0x80aac000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 2791
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights
reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 5.9 (RAMDISK) #43: Sat Feb 27 10:55:39 AEDT 2016
j...@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1041670144 (993MB)
mainbus0 at root
cortex0 at mainbus0
ampintc0 at cortex0 nirq 160
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 4 waymask: 0x0000000f
cpu0 at mainbus0: ARM Cortex A9 R1 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
omap0 at mainbus0: TI OMAP4 PandaBoard
omapid0 at omap0: omap4430
amptimer0: adjusting clock: new tick rate 400000 KHz
prcm0 at omap0 rev 0.0
omdog0 at omap0 rev 0.0
omgpio0 at omap0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at omap0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at omap0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at omap0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at omap0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at omap0: rev 0.1
gpio5 at omgpio5: 32 pins
ommmc0 at omap0
sdmmc0 at ommmc0
com0 at omap0: ti16750, 64 byte fifo
com0: console
ehci0 at omap0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "TI OMAP EHCI root hub" rev 2.00/1.00 addr 1
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd0: 15343MB, 512 bytes/sector, 31422464 sectors
uhub1 at uhub0 port 1 "Standard Microsystems product 0x9514" rev
2.00/2.00 addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address ff:ff:ff:ff:ff:ff
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
panic: pool_do_get: pvepl: page empty
syncing disks... done
rebooting...
U-Boot SPL 2015.10 (Feb 01 2016 - 13:59:48)
OMAP4430 ES2.2
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img
U-Boot 2015.10 (Feb 01 2016 - 13:59:48 +1100)
CPU : OMAP4430 ES2.2
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
reading uboot.env
** Unable to read "uboot.env" from mmc0:1 **
Using default environment
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
159 bytes read in 3 ms (51.8 KiB/s)
Importing environment from mmc0 ...
Running uenvcmd ...
reading bsd.umg
8032536 bytes read in 381 ms (20.1 MiB/s)
## Booting kernel from Legacy Image at 82800000 ...
Image Name: boot
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8032472 Bytes = 7.7 MiB
Load Address: 80300000
Entry Point: 80300000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
OpenBSD/omap booting ...
arg0 0x0 arg1 0xae7 arg2 0x80000100
atag core flags 0 pagesize 0 rootdev 0
atag cmdline [sd0i:/bsd.umg]
atag mem start 0x80000000 size 0x40000000
bootfile: sd0i:/bsd.umg
bootargs:
memory size derived from u-boot
bootconf.mem[0].address = 80000000 pages 262144/0x40000000
Allocating page tables
freestart = 0x80aaa000, free_pages = 259414 (0x0003f556)
IRQ stack: p0x80ad8000 v0xc0ad8000
ABT stack: p0x80ad9000 v0xc0ad9000
UND stack: p0x80ada000 v0xc0ada000
SVC stack: p0x80adb000 v0xc0adb000
Creating L1 page table at 0x80aac000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 2791
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights
reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 5.9 (RAMDISK) #43: Sat Feb 27 10:55:39 AEDT 2016
j...@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1041670144 (993MB)
mainbus0 at root
cortex0 at mainbus0
ampintc0 at cortex0 nirq 160
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 4 waymask: 0x0000000f
cpu0 at mainbus0: ARM Cortex A9 R1 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
omap0 at mainbus0: TI OMAP4 PandaBoard
omapid0 at omap0: omap4430
amptimer0: adjusting clock: new tick rate 400000 KHz
prcm0 at omap0 rev 0.0
omdog0 at omap0 rev 0.0
omgpio0 at omap0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at omap0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at omap0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at omap0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at omap0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at omap0: rev 0.1
gpio5 at omgpio5: 32 pins
ommmc0 at omap0
sdmmc0 at ommmc0
com0 at omap0: ti16750, 64 byte fifo
com0: console
ehci0 at omap0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "TI OMAP EHCI root hub" rev 2.00/1.00 addr 1
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd0: 15343MB, 512 bytes/sector, 31422464 sectors
uhub1 at uhub0 port 1 "Standard Microsystems product 0x9514" rev
2.00/2.00 addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address ff:ff:ff:ff:ff:ff
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
<===========================
Welcome to the OpenBSD/armv7 5.9 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? I
At any prompt except password prompts you can escape to a shell by
typing '!'. Default answers are shown in []'s and are selected by
pressing RETURN. You can exit this program at any time by pressing
Control-C, but this can leave your system in an inconsistent state.
Terminal type? [vt220]
====== abriviate install process =======
# reboot
syncing disks... done
rebooting...
U-Boot SPL 2015.10 (Feb 01 2016 - 13:59:48)
OMAP4430 ES2.2
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img
U-Boot 2015.10 (Feb 01 2016 - 13:59:48 +1100)
CPU : OMAP4430 ES2.2
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
reading uboot.env
** Unable to read "uboot.env" from mmc0:1 **
Using default environment
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
158 bytes read in 3 ms (50.8 KiB/s)
Importing environment from mmc0 ...
Running uenvcmd ...
reading bsd.umg
4668580 bytes read in 215 ms (20.7 MiB/s)
## Booting kernel from Legacy Image at 82800000 ...
Image Name: boot
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4668516 Bytes = 4.5 MiB
Load Address: 80300000
Entry Point: 80300000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
OpenBSD/omap booting ...
arg0 0x0 arg1 0xae7 arg2 0x80000100
atag core flags 0 pagesize 0 rootdev 0
atag cmdline [sd0i:/bsd.umg]
atag mem start 0x80000000 size 0x40000000
bootfile: sd0i:/bsd.umg
bootargs:
memory size derived from u-boot
bootconf.mem[0].address = 80000000 pages 262144/0x40000000
Allocating page tables
freestart = 0x80774000, free_pages = 260236 (0x0003f88c)
IRQ stack: p0x807a2000 v0xc07a2000
ABT stack: p0x807a3000 v0xc07a3000
UND stack: p0x807a4000 v0xc07a4000
SVC stack: p0x807a5000 v0xc07a5000
Creating L1 page table at 0x80774000
Mapping kernel
Constructing L2 page tables
undefined page pmap [ using 397368 bytes of bsd ELF symbol table ]
board type: 2791
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights
reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 5.9 (GENERIC) #182: Sat Feb 27 09:54:34 AEDT 2016
j...@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/GENERIC
real mem = 1073741824 (1024MB)
avail mem = 1044967424 (996MB)
warning: no entropy supplied by boot loader
mainbus0 at root
cortex0 at mainbus0
ampintc0 at cortex0 nirq 160
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 4 waymask: 0x0000000f
cpu0 at mainbus0: ARM Cortex A9 R1 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
omap0 at mainbus0: TI OMAP4 PandaBoard
omapid0 at omap0: omap4430
amptimer0: adjusting clock: new tick rate 400000 KHz
prcm0 at omap0 rev 0.0
omdog0 at omap0 rev 0.0
omgpio0 at omap0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at omap0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at omap0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at omap0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at omap0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at omap0: rev 0.1
gpio5 at omgpio5: 32 pins
ommmc0 at omap0
sdmmc0 at ommmc0
com0 at omap0: ti16750, 64 byte fifo
com0: console
ehci0 at omap0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "TI OMAP EHCI root hub" rev 2.00/1.00 addr 1
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd0: 15343MB, 512 bytes/sector, 31422464 sectors
uhub1 at uhub0 port 1 "Standard Microsystems product 0x9514" rev
2.00/2.00 addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address ff:ff:ff:ff:ff:ff
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
boot device: sd0
root on sd0a (c7543fb3ca77d580.a) swap on sd0b dump on sd0b
WARNING: CHECK AND RESET THE DATE!
Automatic boot in progress: starting file system checks.
/dev/sd0a (c7543fb3ca77d580.a): file system is clean; not checking
/dev/sd0l (c7543fb3ca77d580.l): file system is clean; not checking
/dev/sd0d (c7543fb3ca77d580.d): file system is clean; not checking
/dev/sd0f (c7543fb3ca77d580.f): file system is clean; not checking
/dev/sd0g (c7543fb3ca77d580.g): file system is clean; not checking
/dev/sd0h (c7543fb3ca77d580.h): file system is clean; not checking
/dev/sd0k (c7543fb3ca77d580.k): file system is clean; not checking
/dev/sd0j (c7543fb3ca77d580.j): file system is clean; not checking
/dev/sd0e (c7543fb3ca77d580.e): file system is clean; not checking
setting tty flags
pf enabled
starting network
DHCPREQUEST on smsc0 to 255.255.255.255
DHCPNACK from 192.168.10.1 (00:18:84:a1:71:7c)
DHCPDISCOVER on smsc0 - interval 3
DHCPOFFER from 192.168.10.1 (00:18:84:a1:71:7c)
DHCPREQUEST on smsc0 to 255.255.255.255
DHCPACK from 192.168.10.1 (00:18:84:a1:71:7c)
bound to 192.168.10.177 -- renewal in 21600 seconds.
openssl: generating isakmpd/iked RSA keys... done.
ssh-keygen: generating new host keys: RSA DSA ECDSA ED25519
starting early daemons: syslogd pflogd ntpd.
starting RPC daemons:.
savecore: no core dump
checking quotas: done.
clearing /tmp
kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
starting network daemons: sshd smtpd sndiod.
Path to firmware: http://firmware.openbsd.org/firmware/5.9/
No devices found which need firmware files to be downloaded.
starting local daemons: cron.
Sat Feb 27 08:45:15 JST 2016
OpenBSD/armv7 (arm.my.domain) (console)
login: root
Password:
OpenBSD 5.9 (GENERIC) #182: Sat Feb 27 09:54:34 AEDT 2016
Welcome to OpenBSD: The proactively secure Unix-like operating system.
Please use the sendbug(1) utility to report bugs in the system.
Before reporting a bug, please try to reproduce it with the latest
version of the code. With bug reports, please try to ensure that
enough information to reproduce the problem is enclosed, and if a
known fix for it exists, include that as well.
You have mail.
#
