about 2016-08-18 08:36 miniroot-panda-60.fs
panda reboots several times .
but panda regretably cannot reach the entrance stage of openbsd install .
----------------------
U-Boot SPL 2016.07 (Aug 05 2016 - 23:27:31)
OMAP4430-GP ES2.2
Trying to boot from MMC1
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img
U-Boot 2016.07 (Aug 05 2016 - 23:27:31 -0600)
CPU : OMAP4430-GP ES2.2
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
reading uboot.env
** Unable to read "uboot.env" from mmc0:1 **
Using default environment
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
** Unable to read file uEnv.txt **
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
reading /omap4-panda.dtb
57711 bytes read in 7 ms (7.9 MiB/s)
Found EFI removable media binary efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
65276 bytes read in 10 ms (6.2 MiB/s)
## Starting EFI application at 0x82000000 ...
Scanning disks on usb...
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 5 disks
>> OpenBSD/armv7 BOOTARM 0.1
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2151372+7967356+428532 [64+306496+150318]=0xa81694
OpenBSD/armv7 booting ...
arg0 0x80000000 arg1 0xae7 arg2 0x88000000
Allocating page tables
freestart = 0x80d82000, free_pages = 258686 (0x0003f27e)
IRQ stack: p0x80db0000 v0xc0db0000
ABT stack: p0x80db1000 v0xc0db1000
UND stack: p0x80db2000 v0xc0db2000
SVC stack: p0x80db3000 v0xc0db3000
Creating L1 page table at 0x80d84000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 2791
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 6.0-current (RAMDISK) #10: Thu Aug 18 08:34:59 MDT 2016
dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1038680064 (990MB)
mainbus0 at root: TI OMAP4 PandaBoard
cpu0 at mainbus0: ARM Cortex A9 R1 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 4 waymask: 0x0000000f
omap0 at mainbus0
omapid0 at omap0: omap4430
amptimer0: adjusting clock: new tick rate 400000 KHz
prcm0 at omap0 rev 0.0
ampintc0 at mainbus0 nirq 160
simplebus0 at mainbus0: "ocp"
simplebus1 at simplebus0: "l4"
simplebus2 at simplebus1: "scm"
simplebus3 at simplebus1: "scm"
simplebus4 at simplebus3: "omap4_padconf_global"
simplebus5 at simplebus1: "l4"
omgpio0 at simplebus0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at simplebus0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at simplebus0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at simplebus0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at simplebus0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at simplebus0: rev 0.1
gpio5 at omgpio5: 32 pins
com0 at simplebus0: ti16750, 64 byte fifo
com0: probed fifo depth: 0 bytes
com1 at simplebus0: ti16750, 64 byte fifo
com1: probed fifo depth: 0 bytes
com2 at simplebus0: ti16750, 64 byte fifo
com2: console
com3 at simplebus0: ti16750, 64 byte fifo
com3: probed fifo depth: 0 bytes
tiiic0 at simplebus0 rev 0.10
iic0 at tiiic0
"ti,twl6030" at iic0 addr 0x48 not configured
"ti,twl6040" at iic0 addr 0x4b not configured
tiiic1 at simplebus0 rev 0.10
iic1 at tiiic1
tiiic2 at simplebus0 rev 0.10
iic2 at tiiic2
"ti,eeprom" at iic2 addr 0x50 not configured
tiiic3 at simplebus0 rev 0.10
iic3 at tiiic3
ommmc0 at simplebus0
sdmmc0 at ommmc0: 1-bit, mmc high-speed
ommmc1 at simplebus0
sdmmc1 at ommmc1: 1-bit
omdog0 at simplebus0 rev 0.0
omehci0 at simplebus0
usb0 at omehci0: USB revision 2.0
uhub0 at usb0 "TI OMAP EHCI root hub" rev 2.00/1.00 addr 1
sdmmc1: can't supply clock
sdmmc1: can't enable card
uhub1 at uhub0 port 1 "Standard Microsystems product 0x9514" rev 2.00/2.00
addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address ff:ff:ff:ff:ff:ff
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
sdmmc0: can't enable card
boot device: lookup 'sd0a:/bsd' failed.
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
panic: pool_do_get: pvepl free list modified: page 0xc539a000; item addr
0xc539a6c0; offset 0x0=0xf2737e78 != 0xa4d322d6
syncing disks... done
rebooting...
U-Boot SPL 2016.07 (Aug 05 2016 - 23:27:31)
OMAP4430-GP ES2.2
Trying to boot from MMC1
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img
U-Boot 2016.07 (Aug 05 2016 - 23:27:31 -0600)
CPU : OMAP4430-GP ES2.2
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
reading uboot.env
** Unable to read "uboot.env" from mmc0:1 **
Using default environment
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
** Unable to read file uEnv.txt **
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
reading /omap4-panda.dtb
57711 bytes read in 7 ms (7.9 MiB/s)
Found EFI removable media binary efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
65276 bytes read in 10 ms (6.2 MiB/s)
## Starting EFI application at 0x82000000 ...
Scanning disks on usb...
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 5 disks
>> OpenBSD/armv7 BOOTARM 0.1
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2151372+7967356+428532 [64+306496+150318]=0xa81694
OpenBSD/armv7 booting ...
arg0 0x80000000 arg1 0xae7 arg2 0x88000000
Allocating page tables
freestart = 0x80d82000, free_pages = 258686 (0x0003f27e)
IRQ stack: p0x80db0000 v0xc0db0000
ABT stack: p0x80db1000 v0xc0db1000
UND stack: p0x80db2000 v0xc0db2000
SVC stack: p0x80db3000 v0xc0db3000
Creating L1 page table at 0x80d84000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 2791
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 6.0-current (RAMDISK) #10: Thu Aug 18 08:34:59 MDT 2016
dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1038680064 (990MB)
mainbus0 at root: TI OMAP4 PandaBoard
cpu0 at mainbus0: ARM Cortex A9 R1 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 4 waymask: 0x0000000f
omap0 at mainbus0
omapid0 at omap0: omap4430
amptimer0: adjusting clock: new tick rate 400000 KHz
prcm0 at omap0 rev 0.0
ampintc0 at mainbus0 nirq 160
simplebus0 at mainbus0: "ocp"
simplebus1 at simplebus0: "l4"
simplebus2 at simplebus1: "scm"
simplebus3 at simplebus1: "scm"
simplebus4 at simplebus3: "omap4_padconf_global"
simplebus5 at simplebus1: "l4"
omgpio0 at simplebus0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at simplebus0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at simplebus0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at simplebus0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at simplebus0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at simplebus0: rev 0.1
gpio5 at omgpio5: 32 pins
com0 at simplebus0: ti16750, 64 byte fifo
com0: probed fifo depth: 0 bytes
com1 at simplebus0: ti16750, 64 byte fifo
com1: probed fifo depth: 0 bytes
com2 at simplebus0: ti16750, 64 byte fifo
com2: console
com3 at simplebus0: ti16750, 64 byte fifo
com3: probed fifo depth: 0 bytes
tiiic0 at simplebus0 rev 0.10
iic0 at tiiic0
"ti,twl6030" at iic0 addr 0x48 not configured
"ti,twl6040" at iic0 addr 0x4b not configured
tiiic1 at simplebus0 rev 0.10
iic1 at tiiic1
tiiic2 at simplebus0 rev 0.10
iic2 at tiiic2
"ti,eeprom" at iic2 addr 0x50 not configured
tiiic3 at simplebus0 rev 0.10
iic3 at tiiic3
ommmc0 at simplebus0
sdmmc0 at ommmc0: 1-bit, mmc high-speed
ommmc1 at simplebus0
sdmmc1 at ommmc1: 1-bit
omdog0 at simplebus0 rev 0.0
omehci0 at simplebus0
usb0 at omehci0: USB revision 2.0
uhub0 at usb0 "TI OMAP EHCI root hub" rev 2.00/1.00 addr 1
sdmmc1: can't supply clock
sdmmc1: can't enable card
uhub1 at uhub0 port 1 "Standard Microsystems product 0x9514" rev 2.00/2.00
addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address ff:ff:ff:ff:ff:ff
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
sdmmc0: can't enable card
boot device: lookup 'sd0a:/bsd' failed.
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
panic: pool_do_get: pvepl: page empty
syncing disks... done
rebooting...
U-Boot SPL 2016.07 (Aug 05 2016 - 23:27:31)
OMAP4430-GP ES2.2
Trying to boot from MMC1
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img
U-Boot 2016.07 (Aug 05 2016 - 23:27:31 -0600)
CPU : OMAP4430-GP ES2.2
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
reading uboot.env
** Unable to read "uboot.env" from mmc0:1 **
Using default environment
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
** Unable to read file uEnv.txt **
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
reading /omap4-panda.dtb
57711 bytes read in 8 ms (6.9 MiB/s)
Found EFI removable media binary efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
65276 bytes read in 10 ms (6.2 MiB/s)
## Starting EFI application at 0x82000000 ...
Scanning disks on usb...
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 5 disks
>> OpenBSD/armv7 BOOTARM 0.1
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2151372+7967356+428532 [64+306496+150318]=0xa81694
OpenBSD/armv7 booting ...
arg0 0x80000000 arg1 0xae7 arg2 0x88000000
Allocating page tables
freestart = 0x80d82000, free_pages = 258686 (0x0003f27e)
IRQ stack: p0x80db0000 v0xc0db0000
ABT stack: p0x80db1000 v0xc0db1000
UND stack: p0x80db2000 v0xc0db2000
SVC stack: p0x80db3000 v0xc0db3000
Creating L1 page table at 0x80d84000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 2791
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 6.0-current (RAMDISK) #10: Thu Aug 18 08:34:59 MDT 2016
dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1038680064 (990MB)
mainbus0 at root: TI OMAP4 PandaBoard
cpu0 at mainbus0: ARM Cortex A9 R1 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 4 waymask: 0x0000000f
omap0 at mainbus0
omapid0 at omap0: omap4430
amptimer0: adjusting clock: new tick rate 400000 KHz
prcm0 at omap0 rev 0.0
ampintc0 at mainbus0 nirq 160
simplebus0 at mainbus0: "ocp"
simplebus1 at simplebus0: "l4"
simplebus2 at simplebus1: "scm"
simplebus3 at simplebus1: "scm"
simplebus4 at simplebus3: "omap4_padconf_global"
simplebus5 at simplebus1: "l4"
omgpio0 at simplebus0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at simplebus0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at simplebus0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at simplebus0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at simplebus0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at simplebus0: rev 0.1
gpio5 at omgpio5: 32 pins
com0 at simplebus0: ti16750, 64 byte fifo
com0: probed fifo depth: 0 bytes
com1 at simplebus0: ti16750, 64 byte fifo
com1: probed fifo depth: 0 bytes
com2 at simplebus0: ti16750, 64 byte fifo
com2: console
com3 at simplebus0: ti16750, 64 byte fifo
com3: probed fifo depth: 0 bytes
tiiic0 at simplebus0 rev 0.10
iic0 at tiiic0
"ti,twl6030" at iic0 addr 0x48 not configured
"ti,twl6040" at iic0 addr 0x4b not configured
tiiic1 at simplebus0 rev 0.10
iic1 at tiiic1
tiiic2 at simplebus0 rev 0.10
iic2 at tiiic2
"ti,eeprom" at iic2 addr 0x50 not configured
tiiic3 at simplebus0 rev 0.10
iic3 at tiiic3
ommmc0 at simplebus0
sdmmc0 at ommmc0: 1-bit, mmc high-speed
ommmc1 at simplebus0
sdmmc1 at ommmc1: 1-bit
omdog0 at simplebus0 rev 0.0
omehci0 at simplebus0
usb0 at omehci0: USB revision 2.0
uhub0 at usb0 "TI OMAP EHCI root hub" rev 2.00/1.00 addr 1
sdmmc1: can't supply clock
sdmmc1: can't enable card
uhub1 at uhub0 port 1 "Standard Microsystems product 0x9514" rev 2.00/2.00
addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address ff:ff:ff:ff:ff:ff
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
sdmmc0: can't enable card
boot device: lookup 'sd0a:/bsd' failed.
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
panic: pool_do_get: pvepl: page empty
syncing disks... done
rebooting...
U-Boot SPL 2016.07 (Aug 05 2016 - 23:27:31)
OMAP4430-GP ES2.2
Trying to boot from MMC1
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img
U-Boot 2016.07 (Aug 05 2016 - 23:27:31 -0600)
CPU : OMAP4430-GP ES2.2
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
reading uboot.env
** Unable to read "uboot.env" from mmc0:1 **
Using default environment
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
** Unable to read file uEnv.txt **
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
reading /omap4-panda.dtb
57711 bytes read in 8 ms (6.9 MiB/s)
Found EFI removable media binary efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
65276 bytes read in 10 ms (6.2 MiB/s)
## Starting EFI application at 0x82000000 ...
Scanning disks on usb...
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 5 disks
>> OpenBSD/armv7 BOOTARM 0.1
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2151372+7967356+428532 [64+306496+150318]=0xa81694
OpenBSD/armv7 booting ...
arg0 0x80000000 arg1 0xae7 arg2 0x88000000
Allocating page tables
freestart = 0x80d82000, free_pages = 258686 (0x0003f27e)
IRQ stack: p0x80db0000 v0xc0db0000
ABT stack: p0x80db1000 v0xc0db1000
UND stack: p0x80db2000 v0xc0db2000
SVC stack: p0x80db3000 v0xc0db3000
Creating L1 page table at 0x80d84000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 2791
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 6.0-current (RAMDISK) #10: Thu Aug 18 08:34:59 MDT 2016
dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1038680064 (990MB)
mainbus0 at root: TI OMAP4 PandaBoard
cpu0 at mainbus0: ARM Cortex A9 R1 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 4 waymask: 0x0000000f
omap0 at mainbus0
omapid0 at omap0: omap4430
amptimer0: adjusting clock: new tick rate 400000 KHz
prcm0 at omap0 rev 0.0
ampintc0 at mainbus0 nirq 160
simplebus0 at mainbus0: "ocp"
simplebus1 at simplebus0: "l4"
simplebus2 at simplebus1: "scm"
simplebus3 at simplebus1: "scm"
simplebus4 at simplebus3: "omap4_padconf_global"
simplebus5 at simplebus1: "l4"
omgpio0 at simplebus0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at simplebus0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at simplebus0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at simplebus0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at simplebus0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at simplebus0: rev 0.1
gpio5 at omgpio5: 32 pins
com0 at simplebus0: ti16750, 64 byte fifo
com0: probed fifo depth: 0 bytes
com1 at simplebus0: ti16750, 64 byte fifo
com1: probed fifo depth: 0 bytes
com2 at simplebus0: ti16750, 64 byte fifo
com2: console
com3 at simplebus0: ti16750, 64 byte fifo
com3: probed fifo depth: 0 bytes
tiiic0 at simplebus0 rev 0.10
iic0 at tiiic0
"ti,twl6030" at iic0 addr 0x48 not configured
"ti,twl6040" at iic0 addr 0x4b not configured
tiiic1 at simplebus0 rev 0.10
iic1 at tiiic1
tiiic2 at simplebus0 rev 0.10
iic2 at tiiic2
"ti,eeprom" at iic2 addr 0x50 not configured
tiiic3 at simplebus0 rev 0.10
iic3 at tiiic3
ommmc0 at simplebus0
sdmmc0 at ommmc0: 1-bit, mmc high-speed
ommmc1 at simplebus0
sdmmc1 at ommmc1: 1-bit
omdog0 at simplebus0 rev 0.0
omehci0 at simplebus0
usb0 at omehci0: USB revision 2.0
uhub0 at usb0 "TI OMAP EHCI root hub" rev 2.00/1.00 addr 1
sdmmc1: can't supply clock
sdmmc1: can't enable card
uhub1 at uhub0 port 1 "Standard Microsystems product 0x9514" rev 2.00/2.00
addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address ff:ff:ff:ff:ff:ff
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
sdmmc0: can't enable card
boot device: lookup 'sd0a:/bsd' failed.
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
panic: pool_do_get: pvepl: page empty
syncing disks... done
rebooting...
U-Boot SPL 2016.07 (Aug 05 2016 - 23:27:31)
OMAP4430-GP ES2.2
Trying to boot from MMC1
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img
U-Boot 2016.07 (Aug 05 2016 - 23:27:31 -0600)
CPU : OMAP4430-GP ES2.2
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
reading uboot.env
** Unable to read "uboot.env" from mmc0:1 **
Using default environment
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
** Unable to read file uEnv.txt **
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
reading /omap4-panda.dtb
57711 bytes read in 8 ms (6.9 MiB/s)
Found EFI removable media binary efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
65276 bytes read in 10 ms (6.2 MiB/s)
## Starting EFI application at 0x82000000 ...
Scanning disks on usb...
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 5 disks
>> OpenBSD/armv7 BOOTARM 0.1
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2151372+7967356+428532 [64+306496+150318]=0xa81694
OpenBSD/armv7 booting ...
arg0 0x80000000 arg1 0xae7 arg2 0x88000000
Allocating page tables
freestart = 0x80d82000, free_pages = 258686 (0x0003f27e)
IRQ stack: p0x80db0000 v0xc0db0000
ABT stack: p0x80db1000 v0xc0db1000
UND stack: p0x80db2000 v0xc0db2000
SVC stack: p0x80db3000 v0xc0db3000
Creating L1 page table at 0x80d84000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 2791
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 6.0-current (RAMDISK) #10: Thu Aug 18 08:34:59 MDT 2016
dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1038680064 (990MB)
mainbus0 at root: TI OMAP4 PandaBoard
cpu0 at mainbus0: ARM Cortex A9 R1 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 4 waymask: 0x0000000f
omap0 at mainbus0
omapid0 at omap0: omap4430
amptimer0: adjusting clock: new tick rate 400000 KHz
prcm0 at omap0 rev 0.0
ampintc0 at mainbus0 nirq 160
simplebus0 at mainbus0: "ocp"
simplebus1 at simplebus0: "l4"
simplebus2 at simplebus1: "scm"
simplebus3 at simplebus1: "scm"
simplebus4 at simplebus3: "omap4_padconf_global"
simplebus5 at simplebus1: "l4"
omgpio0 at simplebus0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at simplebus0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at simplebus0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at simplebus0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at simplebus0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at simplebus0: rev 0.1
gpio5 at omgpio5: 32 pins
com0 at simplebus0: ti16750, 64 byte fifo
com0: probed fifo depth: 0 bytes
com1 at simplebus0: ti16750, 64 byte fifo
com1: probed fifo depth: 0 bytes
com2 at simplebus0: ti16750, 64 byte fifo
com2: console
com3 at simplebus0: ti16750, 64 byte fifo
com3: probed fifo depth: 0 bytes
tiiic0 at simplebus0 rev 0.10
iic0 at tiiic0
"ti,twl6030" at iic0 addr 0x48 not configured
"ti,twl6040" at iic0 addr 0x4b not configured
tiiic1 at simplebus0 rev 0.10
iic1 at tiiic1
tiiic2 at simplebus0 rev 0.10
iic2 at tiiic2
"ti,eeprom" at iic2 addr 0x50 not configured
tiiic3 at simplebus0 rev 0.10
iic3 at tiiic3
ommmc0 at simplebus0
sdmmc0 at ommmc0: 1-bit, mmc high-speed
ommmc1 at simplebus0
sdmmc1 at ommmc1: 1-bit
omdog0 at simplebus0 rev 0.0
omehci0 at simplebus0
usb0 at omehci0: USB revision 2.0
uhub0 at usb0 "TI OMAP EHCI root hub" rev 2.00/1.00 addr 1
sdmmc1: can't supply clock
sdmmc1: can't enable card
uhub1 at uhub0 port 1 "Standard Microsystems product 0x9514" rev 2.00/2.00
addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address ff:ff:ff:ff:ff:ff
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
sdmmc0: can't enable card
boot device: lookup 'sd0a:/bsd' failed.
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
panic: pool_do_get: pvepl: page empty
syncing disks... done
rebooting...
U-Boot SPL 2016.07 (Aug 05 2016 - 23:27:31)
OMAP4430-GP ES2.2
Trying to boot from MMC1
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img
U-Boot 2016.07 (Aug 05 2016 - 23:27:31 -0600)
CPU : OMAP4430-GP ES2.2
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
reading uboot.env
** Unable to read "uboot.env" from mmc0:1 **
Using default environment
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
** Unable to read file uEnv.txt **
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
reading /omap4-panda.dtb
57711 bytes read in 7 ms (7.9 MiB/s)
Found EFI removable media binary efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
65276 bytes read in 10 ms (6.2 MiB/s)
## Starting EFI application at 0x82000000 ...
Scanning disks on usb...
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 5 disks
>> OpenBSD/armv7 BOOTARM 0.1
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2151372+7967356+428532 [64+306496+150318]=0xa81694
OpenBSD/armv7 booting ...
arg0 0x80000000 arg1 0xae7 arg2 0x88000000
Allocating page tables
freestart = 0x80d82000, free_pages = 258686 (0x0003f27e)
IRQ stack: p0x80db0000 v0xc0db0000
ABT stack: p0x80db1000 v0xc0db1000
UND stack: p0x80db2000 v0xc0db2000
SVC stack: p0x80db3000 v0xc0db3000
Creating L1 page table at 0x80d84000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 2791
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 6.0-current (RAMDISK) #10: Thu Aug 18 08:34:59 MDT 2016
dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1038680064 (990MB)
mainbus0 at root: TI OMAP4 PandaBoard
cpu0 at mainbus0: ARM Cortex A9 R1 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 4 waymask: 0x0000000f
omap0 at mainbus0
omapid0 at omap0: omap4430
amptimer0: adjusting clock: new tick rate 400000 KHz
prcm0 at omap0 rev 0.0
ampintc0 at mainbus0 nirq 160
simplebus0 at mainbus0: "ocp"
simplebus1 at simplebus0: "l4"
simplebus2 at simplebus1: "scm"
simplebus3 at simplebus1: "scm"
simplebus4 at simplebus3: "omap4_padconf_global"
simplebus5 at simplebus1: "l4"
omgpio0 at simplebus0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at simplebus0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at simplebus0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at simplebus0: rev 0.1
gpio3 at omgpio3: 32 pins
omgpio4 at simplebus0: rev 0.1
gpio4 at omgpio4: 32 pins
omgpio5 at simplebus0: rev 0.1
gpio5 at omgpio5: 32 pins
com0 at simplebus0: ti16750, 64 byte fifo
com0: probed fifo depth: 0 bytes
com1 at simplebus0: ti16750, 64 byte fifo
com1: probed fifo depth: 0 bytes
com2 at simplebus0: ti16750, 64 byte fifo
com2: console
com3 at simplebus0: ti16750, 64 byte fifo
com3: probed fifo depth: 0 bytes
tiiic0 at simplebus0 rev 0.10
iic0 at tiiic0
"ti,twl6030" at iic0 addr 0x48 not configured
"ti,twl6040" at iic0 addr 0x4b not configured
tiiic1 at simplebus0 rev 0.10
iic1 at tiiic1
tiiic2 at simplebus0 rev 0.10
iic2 at tiiic2
"ti,eeprom" at iic2 addr 0x50 not configured
tiiic3 at simplebus0 rev 0.10
iic3 at tiiic3
ommmc0 at simplebus0
sdmmc0 at ommmc0: 1-bit, mmc high-speed
ommmc1 at simplebus0
sdmmc1 at ommmc1: 1-bit
omdog0 at simplebus0 rev 0.0
omehci0 at simplebus0
usb0 at omehci0: USB revision 2.0
uhub0 at usb0 "TI OMAP EHCI root hub" rev 2.00/1.00 addr 1
sdmmc1: can't supply clock
sdmmc1: can't enable card
uhub1 at uhub0 port 1 "Standard Microsystems product 0x9514" rev 2.00/2.00
addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address ff:ff:ff:ff:ff:ff
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
sdmmc0: can't enable card
boot device: lookup 'sd0a:/bsd' failed.
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
