Sorry I meant some optics can do both 1g & 10g On Sun, Sep 26, 2021 at 11:16 AM Trey Scarborough <t...@3dsc.co> wrote:
> correct > On 9/25/2021 2:53 AM, TJ Trout wrote: > > depends if it's 10g or 1g/10g right? > > On Fri, Sep 24, 2021 at 10:17 PM Trey Scarborough <t...@3dsc.co> wrote: > >> No a SFP+ will power up and might even show RX of light, but never come >> up. It works the other way around to if you put a SFP in a SFP+ they will >> often come up and even show RX light at both ends but will not link up. If >> its not a dual rate 1/10G SFP+ that could cause issues. Some don't care, >> but many don't work too well if you try to run them at slower speeds. >> On 9/24/2021 6:39 PM, Steve Jones wrote: >> >> All documentation I find says it's only sfp. But if it doesnt workwouldnt >> it not ID or power? >> >> On Fri, Sep 24, 2021, 6:22 PM Mathew Howard <mhoward...@gmail.com> wrote: >> >>> Will an sfp+ module generally work in an sfp port? I'd be surprised if >>> the Integra has sfp+ >>> >>> On Fri, Sep 24, 2021, 4:33 PM <dmmoff...@gmail.com> wrote: >>> >>>> If you don’t have a ferrule cleaner you can wipe off the ends of the >>>> patch cable with an alcohol wipe, but I have no idea how you clean the >>>> female connectors without the tool. >>>> >>>> -Adam >>>> >>>> >>>> >>>> >>>> >>>> *From:* dmmoff...@gmail.com <dmmoff...@gmail.com> >>>> *Sent:* Friday, September 24, 2021 5:18 PM >>>> *To:* 'AnimalFarm Microwave Users Group' <af@af.afmug.com> >>>> *Subject:* RE: [AFMUG] SFP questions >>>> >>>> >>>> >>>> That “Rx Lose” checkbox at the top on the Mikrotik means there’s no Rx >>>> signal. >>>> >>>> The other device shows Rx power of 0 >>>> >>>> >>>> >>>> If you know it’s physically connected, but there’s no Rx signal on >>>> either end then I’d wonder if you need to flip-flip the tx/rx on one end. >>>> …..sounds like you already tried that though. >>>> >>>> >>>> >>>> Did you clean the connectors? A spec of invisible dirt can stop you. >>>> >>>> >>>> https://www.amazon.com/Cleaning-1-25mm-Ferrule-Connectors-Cleaner/dp/B07Z2ST9GD >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> *From:* AF <af-boun...@af.afmug.com> *On Behalf Of *Steve Jones >>>> *Sent:* Friday, September 24, 2021 5:04 PM >>>> *To:* AnimalFarm Microwave Users Group <af@af.afmug.com> >>>> *Subject:* [AFMUG] SFP questions >>>> >>>> >>>> >>>> Im using my SFPs I have for the Aviat radios to connect between a SAF >>>> integra and a CRS309. >>>> >>>> >>>> >>>> There are two integras 2+0, we lost the original switch that had the >>>> original SFPs in them. So I took the horizontal radio SFP and paired it in >>>> the CRS and that radio links up fine. >>>> >>>> >>>> >>>> However, the SFPs I have for the Aviats dont seem to work. At first I >>>> figured it was just incompatibility (I dont recall if the Integra is SFP or >>>> SFP+, these are SFP+) >>>> >>>> >>>> >>>> In the attached image, both units recognize the SFP and claim to be >>>> transmitting light. Even if there was incompatibility with the SFP, >>>> shouldnt there be an RX? or if they cant negotiate for whatever reason >>>> would it not show an RX? >>>> >>>> >>>> >>>> I did swap the Fiber ends, I havent tried a different cable, though >>>> this was brand new from Aviat. >>>> >>>> >>>> >>>> Would I be correct to assume that if the Devices populate the info >>>> fields, then the SFP should at least connect, even if the the data channel >>>> doesnt work due to incompatibility with the hardware? >>>> >>>> >>>> >>>> -- >>>> AF mailing list >>>> AF@af.afmug.com >>>> http://af.afmug.com/mailman/listinfo/af_af.afmug.com >>>> >>> -- >>> AF mailing list >>> AF@af.afmug.com >>> http://af.afmug.com/mailman/listinfo/af_af.afmug.com >>> >> >> -- >> AF mailing list >> AF@af.afmug.com >> http://af.afmug.com/mailman/listinfo/af_af.afmug.com >> > > -- > AF mailing list > AF@af.afmug.com > http://af.afmug.com/mailman/listinfo/af_af.afmug.com >
-- AF mailing list AF@af.afmug.com http://af.afmug.com/mailman/listinfo/af_af.afmug.com
