depends if it's 10g or 1g/10g right? On Fri, Sep 24, 2021 at 10:17 PM Trey Scarborough <t...@3dsc.co> wrote:
> No a SFP+ will power up and might even show RX of light, but never come > up. It works the other way around to if you put a SFP in a SFP+ they will > often come up and even show RX light at both ends but will not link up. If > its not a dual rate 1/10G SFP+ that could cause issues. Some don't care, > but many don't work too well if you try to run them at slower speeds. > On 9/24/2021 6:39 PM, Steve Jones wrote: > > All documentation I find says it's only sfp. But if it doesnt workwouldnt > it not ID or power? > > On Fri, Sep 24, 2021, 6:22 PM Mathew Howard <mhoward...@gmail.com> wrote: > >> Will an sfp+ module generally work in an sfp port? I'd be surprised if >> the Integra has sfp+ >> >> On Fri, Sep 24, 2021, 4:33 PM <dmmoff...@gmail.com> wrote: >> >>> If you don’t have a ferrule cleaner you can wipe off the ends of the >>> patch cable with an alcohol wipe, but I have no idea how you clean the >>> female connectors without the tool. >>> >>> -Adam >>> >>> >>> >>> >>> >>> *From:* dmmoff...@gmail.com <dmmoff...@gmail.com> >>> *Sent:* Friday, September 24, 2021 5:18 PM >>> *To:* 'AnimalFarm Microwave Users Group' <af@af.afmug.com> >>> *Subject:* RE: [AFMUG] SFP questions >>> >>> >>> >>> That “Rx Lose” checkbox at the top on the Mikrotik means there’s no Rx >>> signal. >>> >>> The other device shows Rx power of 0 >>> >>> >>> >>> If you know it’s physically connected, but there’s no Rx signal on >>> either end then I’d wonder if you need to flip-flip the tx/rx on one end. >>> …..sounds like you already tried that though. >>> >>> >>> >>> Did you clean the connectors? A spec of invisible dirt can stop you. >>> >>> >>> https://www.amazon.com/Cleaning-1-25mm-Ferrule-Connectors-Cleaner/dp/B07Z2ST9GD >>> >>> >>> >>> >>> >>> >>> >>> *From:* AF <af-boun...@af.afmug.com> *On Behalf Of *Steve Jones >>> *Sent:* Friday, September 24, 2021 5:04 PM >>> *To:* AnimalFarm Microwave Users Group <af@af.afmug.com> >>> *Subject:* [AFMUG] SFP questions >>> >>> >>> >>> Im using my SFPs I have for the Aviat radios to connect between a SAF >>> integra and a CRS309. >>> >>> >>> >>> There are two integras 2+0, we lost the original switch that had the >>> original SFPs in them. So I took the horizontal radio SFP and paired it in >>> the CRS and that radio links up fine. >>> >>> >>> >>> However, the SFPs I have for the Aviats dont seem to work. At first I >>> figured it was just incompatibility (I dont recall if the Integra is SFP or >>> SFP+, these are SFP+) >>> >>> >>> >>> In the attached image, both units recognize the SFP and claim to be >>> transmitting light. Even if there was incompatibility with the SFP, >>> shouldnt there be an RX? or if they cant negotiate for whatever reason >>> would it not show an RX? >>> >>> >>> >>> I did swap the Fiber ends, I havent tried a different cable, though this >>> was brand new from Aviat. >>> >>> >>> >>> Would I be correct to assume that if the Devices populate the info >>> fields, then the SFP should at least connect, even if the the data channel >>> doesnt work due to incompatibility with the hardware? >>> >>> >>> >>> -- >>> AF mailing list >>> AF@af.afmug.com >>> http://af.afmug.com/mailman/listinfo/af_af.afmug.com >>> >> -- >> AF mailing list >> AF@af.afmug.com >> http://af.afmug.com/mailman/listinfo/af_af.afmug.com >> > > -- > AF mailing list > AF@af.afmug.com > http://af.afmug.com/mailman/listinfo/af_af.afmug.com >
-- AF mailing list AF@af.afmug.com http://af.afmug.com/mailman/listinfo/af_af.afmug.com
