Which model do you gentlemen use, the 800-GIGE-SS-HV ?
On Fri, Jul 16, 2021 at 3:30 PM Darren Shea <darr...@ecpi.com> wrote: > I know there’s supposedly no such thing as a stupid question, so please be > kind if this actually is one, but… > > > > Might there be a way to increase the distance between the cable jack and > the bottom of the box? I don’t really have an issue when I’m cutting and > crimping a new fitting on a cable, but if I want to use a premade cable > with strain-relief, that’s when my mumbled curses start flying. Even a > half-centimeter more of a gap might help… > > > > *From:* AF [mailto:af-boun...@af.afmug.com] *On Behalf Of *Chuck McCown > via AF > *Sent:* Friday, July 16, 2021 2:24 PM > *To:* AnimalFarm Microwave Users Group > *Cc:* Chuck McCown > *Subject:* Re: [AFMUG] Cambium Force 300 Ethernet question > > > > There is not enough room to make a hole large enough for a grommet that > will allow a cat5 plug to pass. We have about .735” to work with. You > need a minimum of .750 hole and the grommet itself is 1” dia. > > > > I could do a split grommet that would just fit the CAT5 but then you will > have to install the grommet with cable filling it and that will be a big > pain forcing it in. The other seal that is already there slides out so you > are not having to force a round grommet into the hole. > > > > It is easy if the grommet doesn’t have anything going through the center > when you install it. > > > > I doubt no one wants to feed the wire through then install the plug. > > > > *From:* Jason McKemie > > *Sent:* Friday, July 16, 2021 11:56 AM > > *To:* AnimalFarm Microwave Users Group > > *Subject:* Re: [AFMUG] Cambium Force 300 Ethernet question > > > > I've drilled holes in the bottom of the DC SS enclosures, directly below > the connectors. Works well enough for those, it would be a bit more of a > pain with the RJ45 connector though since you'd have to install the end > afterwards. > > > > On Fri, Jul 16, 2021 at 11:51 AM Carl Peterson <cpeter...@portnetworks.com> > wrote: > > We have recently seen similar issues when using Chuck's surge > suppressors. Not sure what changed, the RJ 45s, The jack Chuck uses, or my > techs but we figured out that it was caused by the cable getting pulled > sideways in the surge enclosure and the tolerance stack on the RJ/RJ jack > just not working in our favor. Now we add a zip tie in the little > enclosure to force a bend/cross in the in/out cable. > > > > P.S. If you are reading this Chuck we would really really like an > enclosure with a separate in/out feed similar to the 600SS or something > like that so the cable can go straight up into the jack and not get pulled > sideways. > > > > On Thu, Jul 15, 2021 at 10:44 PM Nate Burke <n...@blastcomm.com> wrote: > > I've put up alot of the F300, haven't seen any problems. Bad cable or > Radio? Did you try a different POE? 9/10 times Ethernet seems to be a > problem with the termination and/or cable. I've done 1000's of ends, but > just the other day I did one with one blue and green wire switched, I think > that caused weird Ethernet problems. Of course it was the end at the radio > and not the easy-to-get-to inside connection. > > On 7/15/2021 9:32 PM, Jaime Solorza wrote: > > Installed a PTP link with great signal but Ethernet port will not lock at > 1000FDX...only 100FDx...if i force it it loses connection or 10mbps hex... > > Latest firmware... > > Any ideas? > > I even put a Trendnet Ethernet switch between Poe and Edgeswitch... > > Thanks > > > > > > -- > AF mailing list > AF@af.afmug.com > http://af.afmug.com/mailman/listinfo/af_af.afmug.com > > > > > > -- > > Carl Peterson > > *PORT NETWORKS* > > 401 E Pratt St, Ste 2553 > > Baltimore, MD 21202 > > (410) 637-3707 > > -- > AF mailing list > AF@af.afmug.com > http://af.afmug.com/mailman/listinfo/af_af.afmug.com > > ------------------------------ > > -- > AF mailing list > AF@af.afmug.com > http://af.afmug.com/mailman/listinfo/af_af.afmug.com > -- > AF mailing list > AF@af.afmug.com > http://af.afmug.com/mailman/listinfo/af_af.afmug.com >
-- AF mailing list AF@af.afmug.com http://af.afmug.com/mailman/listinfo/af_af.afmug.com
