ouch, no access at all? assuming you changed ap/sm mode to change this? On Wed, Dec 4, 2019 at 12:47 PM Nate Burke <n...@blastcomm.com> wrote:
> Apparently disabling the primary disables 'BOTH' ports. Looks like the > truck is rolling. > > On 12/4/2019 12:32 PM, Nate Burke wrote: > > ooh, that's a good idea! > > On 12/4/2019 12:16 PM, Adam Moffett wrote: > > Did I read that it was a point to point? Can reverse roles so the AP is > on the other end? > > > On 12/4/2019 1:00 PM, Nate Burke wrote: > > It looks like when the radio is in AP mode, (nonGPS Radio) then you can't > disable the primary Ethernet port. I tried from the CLI, and it greyed out > all the ethernet options in the GUI, but the radio still showed the LAN as > up. > > On 12/4/2019 9:50 AM, Steve Jones wrote: > > [image: image.png]This is on a gps 2.4. It would make sense to not be > able to disable the ethernet on an AP as it would be inaccessible > Here are some configs to dick with > "mgmtIFEnable": "0", > "networkLanEnabled": "1", > "networkLan2Enabled": "1", > > probably "networkLanEnabled": "0", would disable the port > > Thats if you download the json, edit it and upload it, or push it from > cnmaestro. I dont know the syntax for CLI > > > > On Wed, Dec 4, 2019 at 9:01 AM Nate Burke <n...@blastcomm.com> wrote: > >> Thanks! I'm upgrading the firmware now, the radio was on 3.5.1 >> >> Ok, ready to pull my hair out now. >> >> Radios were on 3.5.1, just upgraded to 3.5.6. The 2.4 SM (nonGPS), has >> the option to disable the Ethernet port, but the 2.4ap (nonGPS) does not >> have that option. >> If the Radio is set as an AP, does that option go away? >> >> AP Radio (EPMP1000 NonGPS) >> >> SM Radio (EPMP1000 NonGPS) >> >> >> >> >> It's an interesting setup, CustomerA provides POE and is connected via >> Ethernet to the 2.4 radio. The Aux Port of the 2.4 radio powers a 5ghz >> Feed radio. Customer B connects via RF to the 2.4 radio. CustomerA isn't >> paying their bill, so I need to turn them off. >> >> CustomerB owns the house of CustomerA, so I'm not worried about them >> getting pissed off and unplugging it, as CustomerB can just go plug it in >> again. >> >> On 12/4/2019 8:28 AM, Adam Moffett wrote: >> >> This is a 2.4 unit on 3.5.6.....but it looks like you can turn off the >> primary port. >> >> If that option isn't there on yours, what about disabling the switch port >> at the bottom or just unplugging it at the bottom? >> >> >> On 12/4/2019 9:19 AM, Nate Burke wrote: >> >> Is there a way to disable the Ethernet on the primary port but leave the >> aux port active? You can Disable the Aux port, but there isn't a setting >> to disable the Primary port. I need to kill the traffic on the port that >> is providing the POE, but leave the aux port active. >> >> >> >> >> >> >> -- >> AF mailing list >> AF@af.afmug.com >> http://af.afmug.com/mailman/listinfo/af_af.afmug.com >> > > > > > > > > > > > -- > AF mailing list > AF@af.afmug.com > http://af.afmug.com/mailman/listinfo/af_af.afmug.com >
-- AF mailing list AF@af.afmug.com http://af.afmug.com/mailman/listinfo/af_af.afmug.com
