On Wed, Sep 13, 2017 at 10:04 AM, yahia farghaly <yahiafargh...@gmail.com> wrote:
> > Thanks for replying but it gives me this error log > > >> *ERROR: rpi-hwup-image-1.0-r0 do_rootfs: Unable to install packages. >> Command >> '/yocto/poky/build/tmp/work/raspberrypi3-poky-linux-gnueabi/rpi-hwup-image/1.0-r0/recipe-sysroot-native/usr/bin/apt-get >> install --force-yes --allow-unauthenticated run-postinsts >> packagegroup-core-boot kernel-modules rpi-config' returned 100:* >> *Reading package lists...* >> *Building dependency tree...* >> *Reading state information...* >> *Package rpi-config is not available, but is referred to by another >> package.* >> *This may mean that the package is missing, has been obsoleted, or**is >> only available from another source* >> *E: Package 'rpi-config' has no installation candidate* >> >> *ERROR: rpi-hwup-image-1.0-r0 do_rootfs: Function failed: do_rootfs* >> *ERROR: Logfile of failure stored in: >> /yocto/poky/build/tmp/work/raspberrypi3-poky-linux-gnueabi/rpi-hwup-image/1.0-r0/temp/log.do_rootfs.2252**ERROR: >> Task >> (/yocto/poky/meta-raspberrypi/recipes-core/images/rpi-hwup-image.bb:do_rootfs) >> failed with exit code '1'* > > > All what i did is IMAGE_INSTALL_append = "rpi-config" , the recipe file > is not exist in the meta-raspberry > You missed the space before rpi-config from the original suggestion in IMAGE_INSTALL_append. This is always required when overriding variables with _append > > > > On 13 September 2017 at 09:27, Ayoub Zaki <ayoub.z...@embexus.com> wrote: > >> I ran into the same problem: >> >> ENABLE_UART = "1" is not enough you should also add INSTALL_append= " >> rpi-config" to your local.conf and Serial port will be enabled. >> >> On 12.09.2017 14:09, yahia farghaly wrote: >> >> I have bitbaked rpi-hwup-image for raspberry pi 3 on sd card and >> connected the serial ports to *usb to ttl device* . i have set the >> minicom to >> port: /dev/ttyUSB0 >> baud rate: 115200 >> the image is booting fine and i can see the prompt on the screen but >> cannot see in my serial console using minicom. >> *is serial enabled by default for this image ? * >> i also tried ENABLE_UART = "1" in local.conf but doesn't help. >> >> how to enable it ? and what the serial device name with respect to >> raspberry pi >> >> thanks, >> >> -- >> Yahia Farghaly >> Graduated from Faculty of Engineering - Electronics and Communications >> Department at Cairo University. >> Linkedin <https://linkedin.com/in/yahiafarghaly> - GitHub >> <https://github.com/yahiafarghaly> >> >> >> >> >> >> >> >> -- >> >> Ayoub Zaki >> Embedded Systems Consultant >> >> Vaihinger Str. 2/1 >> 71634 Ludwigsburg >> >> e-mail: ayoub.z...@embexus.com >> Tel: +49176-62901545 <+49%20176%2062901545>https://embexus.com >> >> >> -- >> _______________________________________________ >> yocto mailing list >> yocto@yoctoproject.org >> https://lists.yoctoproject.org/listinfo/yocto >> >> > > > -- > Yahia Farghaly > Graduated from Faculty of Engineering - Electronics and Communications > Department at Cairo University. > Linkedin <https://linkedin.com/in/yahiafarghaly> - GitHub > <https://github.com/yahiafarghaly> > > -- > _______________________________________________ > yocto mailing list > yocto@yoctoproject.org > https://lists.yoctoproject.org/listinfo/yocto > >
-- _______________________________________________ yocto mailing list yocto@yoctoproject.org https://lists.yoctoproject.org/listinfo/yocto
