As Rainer mentioned the issue is likely that the unit group has not been defined for the PM4 obs type in your database (though this will depend on your driver setup, database schema and skin you are using). Unit groups for additional obs types are often defined by the user in extensions.py, but can also be done in the driver. The gateway driver does define unit groups for all WeeWX fields in the default field map that do not appear in the default WeeWX schema (ie the wview_extended schema). I neglected to update this portion of the driver for the new/updated 'PM' fields in v0.6.3.b1, I have since made the necessary changes. If you delete the v0.6.3b1 driver using:
$ rm /etc/weewx/bin/user/gw1000.py and then download v0.6.3b2 in it's place using: $ wget -P /etc/weewx/bin/user https://raw.githubusercontent.com/gjr80/weewx-gw1000/v0.6.3/bin/user/gw1000.py and finally restart WeeWX your PM4 data should display with correct formatting/labelling. Gary On Thursday 1 August 2024 at 16:08:48 UTC+10 j.fri...@gmail.com wrote: > Hi Gary, > > the v0.6.3b1 works wery well. There is only one possible issue with PMI > 4. index.html page shows it in other way then others values . > > Thank you very much for your help. > > Jarda > > *Outout from the driver :* > 'pm1_0': '9.5', 'pm1_0_24h_avg': '1.5', 'pm2_55': '10.6', > 'pm2_55_24h_avg': '2.5', 'pm4_0': '11.0', 'pm4_0_24h_avg': '3.2', 'pm10_0': > '11.2', 'pm10_0_24h_avg': '3.6' > > *Database values :* > PM1.0 = 10.6333333333333 > PM2.5 = 11.7 > PM4.0 = 12.0666666666667 > PM10 = 12.2666666666667 > > *Index.html page :* > [image: Výstřižek.PNG] > > > > Dne úterý 30. července 2024 v 13:51:16 UTC+2 uživatel gjr80 napsal: > > You can try v0.6.3b1 which includes support for the WH46 air quality > sensor. If a WH46 is connected the v0.6.3 driver should emit the same > temperature, PM2.5, PM10 and CO2 fields as with a WH45. Additional fields > pm1_0, pm1_0_24h_avg, pm4_0, pm4_0_24h_avg should also be emitted with > the WH46 PM1 and PM4 data and 24hour averages respectively. v0.6.3 should > also automatically determine whether a WH45 or WH46 is present and > correctly name WH45/WH46 battery and signal state fields. > > Note that I have had to change the names of a the PM10 fields emitted by > the driver when used with a WH45 sensor. This will only affect you if you > previously used a WH45 sensor. The driver now emits pm10_0 and > pm10_0_24h_avg fields (previously the fields were pm10 and pm10_24h_avg). > Users who have previously used a WH45 sensor will need to either change > their field map if mapping these fields to some other WeeWX field, or if > the pm10 and pm10_24h_avg fields are used in the database schema the > database fields will need to be renamed to the new field names. > > v0.6.3 also includes support for the WS85 sensor array as well as > including a revised approach to device discovery that is much more reliable > than the previous approach. Note the recommended approach remains to > specify the device IP address in the WeeWX config file rather than have the > driver rely on discovery > > I have not released v0.6.3 yet, rather I have kept it at b1 until someone > verifies it's use it with a WH45/46. If you wish to try v0.6.3b1 the > following instructions should be used: > > 1. Rename your existing gateway driver to gw1000_0_6_1.py so you can > easily revert if necessary: > $ cp /etc/weewx/bin/user/gw1000.py /etc/weewx/bin/user/gw1000_0_6_1.py > > 2. Download the v0.6.3b1 driver file and save it to /etc/weewx/bin/user: > $ wget -P /etc/weewx/bin/user > https://raw.githubusercontent.com/gjr80/weewx-gw1000/v0.6.3/bin/user/gw1000.py > > 3. You can run the driver directly as you did in you OP, you should see > the WH46 obs fields as well as WH46 battery and signal state data. You > might also find using the --live-data option useful when running the > driver directly. > > 4. If you are happy running the driver directly you can restart WeeWX and > it will pick up the v0.6.3 driver. > > Note the above commands may require prefixing with sudo. If you need to > revert to your original driver just delete /etc/weewx/bin/user/gw1000.py and > rename /etc/weewx/bin/user/gw1000_0_6_1.py to > /etc/weewx/bin/user/gw1000.py. > > If any problems please let me know. > > Gary > > On Monday 29 July 2024 at 22:55:21 UTC+10 j.fri...@gmail.com wrote: > > Hello, > > I added new WH46 to my Ecowitt system. I can view data in ecowitt.net and > in mobile application too. > > My main system is weewx https://pocasi.frimlovi.com but the new WH46 data > didn't appear automatically in dashboard. > > If I run PYTHONPATH=/usr/share/weewx:/etc/weewx/bin python3 > /etc/weewx/bin/user/gw1000.py --test-service --ip-address=my_IP it shows > data from all measures correctly but from WH46 it shows only data about > battery and signal - 'wh45_batt': '5', 'wh45_sig': '4' > > I use the latest version of GW1000 driver - 0.6.1 > > I tryed to add data in weewx.conf - [[field_map_extensions]] and in > skin.conf in appearance but nothing changed. > > Can you help me please ? > > Thank you in advance. > > Jarda > > -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to weewx-user+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/68515a54-d1cd-4dbd-985a-5c864017f4c4n%40googlegroups.com.
