Hi Robert,

Can you try rebuilding gr-ettus with the cmake flag
"-DCMAKE_BUILD_TYPE=Debug" and see if the issue goes away?

Jonathon

On Fri, Nov 6, 2020 at 8:57 AM Robert Wilson <robertbenwils...@gmail.com>
wrote:

>   Hi Jonathon,
>
> I've reduced both with no change.
>
> Ben
>
> On Wed, Nov 4, 2020 at 1:59 PM Jonathon Pendlum <
> jonathon.pend...@ettus.com> wrote:
>
>> Hi Robert,
>>
>> Try using the maximum MTU size supported. Also, try reducing the FFT size
>> and SPP to 512.
>>
>> Jonathon
>>
>> On Wed, Nov 4, 2020 at 8:45 AM Robert Wilson <robertbenwils...@gmail.com>
>> wrote:
>>
>>> My Ethernet Controller is a Qualcomm Atheros AR8151 it’s max MTU is 6144
>>> bytes. I’ve changed MTU to the max with no change in gnuRadio response. Is
>>> the 6144 bytes not enough?
>>>
>>> On Tue, Nov 3, 2020 at 9:32 PM Jonathon Pendlum <
>>> jonathon.pend...@ettus.com> wrote:
>>>
>>>> Hi Ben,
>>>>
>>>> Try setting your NIC's MTU to 9000.
>>>>
>>>> Jonathon
>>>>
>>>> On Mon, Nov 2, 2020 at 6:55 AM Robert Wilson via USRP-users <
>>>> usrp-users@lists.ettus.com> wrote:
>>>>
>>>>> Hello,
>>>>>
>>>>> OS: Linux Ubuntu 20.04.1 LTS
>>>>> GRC: 3.8
>>>>> UHD: 4.0
>>>>> USRP:X310 (HG)
>>>>>
>>>>> I have been looking at RFNoC only for a few weeks. I have followed the
>>>>> RFNoC Workshop 4 tutorial and successfully built my own custom gain block
>>>>> as well as implemented and FFT from existing blocks using the "Getting
>>>>> Started with RFNoC" document online.
>>>>>
>>>>> I am now attempting to get Fosphor up and running on my X310 to
>>>>> further understand bitstream generation from YAML files. At one point I
>>>>> believe there was an example bitstream that had the correct Fosphor
>>>>> configuration I don't see it in the build of UHD I have.
>>>>>
>>>>> I've attached my .yml file and a copy of my GRC flow graph.
>>>>> Below is the error message I'm receiving.
>>>>>
>>>>> [INFO] [UHD] linux; GNU C++ version 9.3.0; Boost_107100;
>>>>> UHD_4.0.0.0-1-gcf570707
>>>>> [INFO] [X300] X300 initialization sequence...
>>>>> [INFO] [X300] Maximum frame size: 1472 bytes.
>>>>> [INFO] [GPS] No GPSDO found
>>>>> [INFO] [X300] Radio 1x clock: 200 MHz
>>>>> [WARNING] [RFNOC::BLOCK_FACTORY] Could not find block with Noc-ID
>>>>> 0xfd7d809a, 0xffff
>>>>> [WARNING] [0/Radio#0] Setting RX IQ Balance is not possible on this
>>>>> device.
>>>>> gr::log :DEBUG: rfnoc_rx_streamer0 - Committing graph...
>>>>> [WARNING] [0/Radio#0] Attempting to set tick rate to 0. Skipping.
>>>>> gr::log :DEBUG: rfnoc_rx_streamer1 - Committing graph...
>>>>> gr::log :DEBUG: rfnoc_rx_streamer1 - Sending start stream command...
>>>>> gr::log :DEBUG: rfnoc_rx_streamer0 - Sending start stream command...
>>>>>
>>>>> >>> Done (return code -11)
>>>>>
>>>>> More resources of this type of development would be welcome as well.
>>>>>
>>>>> Many Thanks,
>>>>> Ben Wilson
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> USRP-users mailing list
>>>>> USRP-users@lists.ettus.com
>>>>> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
>>>>>
>>>>
_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com

Reply via email to