Greetings Nate, Thanks for getting back to me so quickly. I will be sure to flash the OS to release 4 and roll back my dev environment to match the instructions.
Regards, Jon Lockhart On Fri, Oct 11, 2019, 1:20 PM Nate Temple <nate.tem...@ettus.com> wrote: > Hi Jon, > > If you are following this app note [0], I would recommend starting with > the release-4 image. The pre-3.15 MPM based image that has been released is > currently a "beta" release. It lacks several of the dependencies required > to build out GNU Radio. We are working on a new release and hope to have it > posted soon. > > [0] - > https://kb.ettus.com/Software_Development_on_the_E3xx_USRP_-_Building_RFNoC_UHD_/_GNU_Radio_/_gr-ettus_from_Source > > > Regards, > Nate Temple > > On Fri, Oct 11, 2019 at 10:14 AM Jonathan Lockhart <jlockhar...@gmail.com> > wrote: > >> Greetings Ettus Radio List, >> >> I have recently acquired and began using an Ettus E312 and have been >> trying to configure the dev host and the cross compile environment. >> Unfortunately I am having issues completing some of these tasks with the >> pre-release version of 3.15 image that Ettus mentions you should use in the >> manual for the E312. I forward those issues to support but have heard no >> reply. Please refer below to the issues I am reporting. The GNURadio cross >> compile issue with the SDK and environment is the more crucial one at the >> moment. I was wondering if anyone else has been experiencing these issues >> and if so how did you proceed to get it resolved. Is there an image, sdk, >> GNURadio version that I should be using other than the 3.15 image and >> instructions that Ettus currently recommends using until a stable RC is >> provided? >> >> Thanks for your help and feedback. >> >> Regards, >> Jon Lockhart >> >> >> ---------- Forwarded message --------- >> From: Jonathan Lockhart <jlockhar...@gmail.com> >> Date: Mon, Oct 7, 2019 at 3:16 PM >> Subject: Issues Completing Radio Build and Installation >> To: <supp...@ettus.com> >> >> >> Greetings Ettus Support, >> >> I recently acquired an Ettus E312 and I was looking to do some >> development on it. Unfortunately I am have been having some issues. The >> manual via files.ettus.com and the "Getting Started" both failed to >> provide a working environment. >> >> The farthest I got was downloading the meta section direction for the >> E312 to get 3.15.0 image and sdk for the radio, and then following this >> guide page for 3.14, correcting the UHD install accordingly to comply with >> 3.15. (Guide >> https://kb.ettus.com/Software_Development_on_the_E3xx_USRP_-_Building_RFNoC_UHD_/_GNU_Radio_/_gr-ettus_from_Source#Running_RFNoC_Fosphor >> ) >> >> When mounting the cross compiled UHD folders via the instructions on the >> radio, and using the uhd_usrp_probe command, there is an error checking for >> the libusb_init information. >> >> root@ni-e31x-313179A:~/newinstall# uhd_usrp_probe >> [INFO] [UHD] linux; GNU C++ version 7.3.0; Boost_106600; >> UHD_3.15.0.HEAD-0-g6563c537 >> [ERROR] [UHD] Device discovery error: AssertionError: >> libusb_init(&_context) == 0 >> in libusb_session_impl::libusb_session_impl() >> at /home/jon/rfnoc/src/uhd/host/lib/transport/libusb1_base.cpp:36 >> >> [ERROR] [UHD] Device discovery error: AssertionError: >> libusb_init(&_context) == 0 >> in libusb_session_impl::libusb_session_impl() >> at /home/jon/rfnoc/src/uhd/host/lib/transport/libusb1_base.cpp:36 >> >> [ERROR] [UHD] Device discovery error: AssertionError: >> libusb_init(&_context) == 0 >> in libusb_session_impl::libusb_session_impl() >> at /home/jon/rfnoc/src/uhd/host/lib/transport/libusb1_base.cpp:36 >> >> [INFO] [MPMD] Initializing 1 device(s) in parallel with args: >> mgmt_addr=127.0.0.1,type=e3xx,product=e310_sg3,serial=313179A,claimed=False >> [INFO] [MPM.PeriphManager] Found 1 daughterboard(s). >> [INFO] [MPM.PeriphManager] init() called with device args >> `product=e310_sg3,mgmt_addr=127.0.0.1'. >> [INFO] [0/Radio_0] Initializing block control (NOC ID: 0x12AD100000003310) >> [INFO] [0/DDC_0] Initializing block control (NOC ID: 0xDDC0000000000000) >> [INFO] [0/DUC_0] Initializing block control (NOC ID: 0xD0C0000000000002) >> [INFO] [0/Radio_0] RX freq = 2.4e+09 >> [INFO] [0/Radio_0] RX band = 6 >> [INFO] [0/Radio_0] RX SW1 = 5 >> [INFO] [0/Radio_0] RX SWC = 0 >> [INFO] [0/Radio_0] RX SWB = 1 >> [INFO] [0/Radio_0] RX VCRX_SW = 1 >> [INFO] [0/Radio_0] RX VCTXRX_SW = 0 >> [INFO] [0/Radio_0] RX freq = 2.4e+09 >> [INFO] [0/Radio_0] RX band = 6 >> [INFO] [0/Radio_0] RX SW1 = 5 >> [INFO] [0/Radio_0] RX SWC = 0 >> [INFO] [0/Radio_0] RX SWB = 1 >> [INFO] [0/Radio_0] RX VCRX_SW = 1 >> [INFO] [0/Radio_0] RX VCTXRX_SW = 0 >> [INFO] [0/Radio_0] RX freq = 2.4e+09 >> [INFO] [0/Radio_0] RX band = 6 >> [INFO] [0/Radio_0] RX SW1 = 5 >> [INFO] [0/Radio_0] RX SWC = 0 >> [INFO] [0/Radio_0] RX SWB = 1 >> [INFO] [0/Radio_0] RX VCRX_SW = 1 >> [INFO] [0/Radio_0] RX VCTXRX_SW = 0 >> [INFO] [0/Radio_0] RX freq = 2.4e+09 >> [INFO] [0/Radio_0] RX band = 6 >> [INFO] [0/Radio_0] RX SW1 = 5 >> [INFO] [0/Radio_0] RX SWC = 0 >> [INFO] [0/Radio_0] RX SWB = 1 >> [INFO] [0/Radio_0] RX VCRX_SW = 1 >> [INFO] [0/Radio_0] RX VCTXRX_SW = 0 >> [INFO] [0/Radio_0] RX freq = 2.4e+09 >> [INFO] [0/Radio_0] RX band = 6 >> [INFO] [0/Radio_0] RX SW1 = 5 >> [INFO] [0/Radio_0] RX SWC = 0 >> [INFO] [0/Radio_0] RX SWB = 1 >> [INFO] [0/Radio_0] RX VCRX_SW = 1 >> [INFO] [0/Radio_0] RX VCTXRX_SW = 0 >> [INFO] [0/Radio_0] RX freq = 2.4e+09 >> [INFO] [0/Radio_0] RX band = 6 >> [INFO] [0/Radio_0] RX SW1 = 5 >> [INFO] [0/Radio_0] RX SWC = 0 >> [INFO] [0/Radio_0] RX SWB = 1 >> [INFO] [0/Radio_0] RX VCRX_SW = 1 >> [INFO] [0/Radio_0] RX VCTXRX_SW = 0 >> [INFO] [0/Radio_0] Performing CODEC loopback test... >> [INFO] [0/Radio_0] CODEC loopback test passed >> [INFO] [0/Radio_0] Performing CODEC loopback test... >> [INFO] [0/Radio_0] CODEC loopback test passed >> _____________________________________________________ >> / >> | Device: E300-Series Device >> | _____________________________________________________ >> | / >> | | Mboard: ni-e31x-313179A >> | | mpm_version: 3.15.0.git-g6563c537 >> | | pid: 30675 >> | | product: e310_sg3 >> | | rev: 7 >> | | rpc_connection: local >> | | serial: 313179A >> | | type: e3xx >> | | MPM Version: 1.2 >> | | FPGA Version: 1.0 >> | | FPGA git hash: f52a643.clean >> | | RFNoC capable: Yes >> | | >> | | Time sources: internal, external, gpsdo >> | | Clock sources: internal >> | | Sensors: ref_locked, temp_fpga, temp_mb >> | | _____________________________________________________ >> | | / >> | | | RX Dboard: A >> | | | _____________________________________________________ >> | | | / >> | | | | RX Frontend: 0 >> | | | | Name: E3xx >> | | | | Antennas: RX2, TX/RX >> | | | | Sensors: lo_locked, ad9361_temperature, rssi, lo_lock >> | | | | Freq range: 70.000 to 6000.000 MHz >> | | | | Gain range PGA: 0.0 to 76.0 step 1.0 dB >> | | | | Bandwidth range: 20000000.0 to 40000000.0 step 0.0 Hz >> | | | | Connection Type: IQ >> | | | | Uses LO offset: No >> | | | _____________________________________________________ >> | | | / >> | | | | RX Frontend: 1 >> | | | | Name: E3xx >> | | | | Antennas: RX2, TX/RX >> | | | | Sensors: lo_locked, ad9361_temperature, rssi, lo_lock >> | | | | Freq range: 70.000 to 6000.000 MHz >> | | | | Gain range PGA: 0.0 to 76.0 step 1.0 dB >> | | | | Bandwidth range: 20000000.0 to 40000000.0 step 0.0 Hz >> | | | | Connection Type: IQ >> | | | | Uses LO offset: No >> | | | _____________________________________________________ >> | | | / >> | | | | RX Codec: A >> | | | | Name: AD9361 Dual ADC >> | | | | Gain Elements: None >> | | _____________________________________________________ >> | | / >> | | | TX Dboard: A >> | | | _____________________________________________________ >> | | | / >> | | | | TX Frontend: 0 >> | | | | Name: E3xx >> | | | | Antennas: TX/RX >> | | | | Sensors: lo_locked, ad9361_temperature >> | | | | Freq range: 47.000 to 6000.000 MHz >> | | | | Gain range PGA: 0.0 to 89.8 step 0.2 dB >> | | | | Bandwidth range: 20000000.0 to 40000000.0 step 0.0 Hz >> | | | | Connection Type: IQ >> | | | | Uses LO offset: No >> | | | _____________________________________________________ >> | | | / >> | | | | TX Frontend: 1 >> | | | | Name: E3xx >> | | | | Antennas: TX/RX >> | | | | Sensors: lo_locked, ad9361_temperature >> | | | | Freq range: 47.000 to 6000.000 MHz >> | | | | Gain range PGA: 0.0 to 89.8 step 0.2 dB >> | | | | Bandwidth range: 20000000.0 to 40000000.0 step 0.0 Hz >> | | | | Connection Type: IQ >> | | | | Uses LO offset: No >> | | | _____________________________________________________ >> | | | / >> | | | | TX Codec: A >> | | | | Name: AD9361 Dual DAC >> | | | | Gain Elements: None >> | | _____________________________________________________ >> | | / >> | | | RFNoC blocks on this device: >> | | | >> | | | * Radio_0 >> | | | * DDC_0 >> | | | * DUC_0 >> >> It does appear however that the command runs properly even without the >> USB files being available. >> >> As for GNU radio, well that won't cross compile. The base installation >> works with no issues, but when I go to cross compile in the SDK environment >> for 3.15, I get the following issue: >> >> ~/rfnoc/src/gnuradio/build-arm$ cmake -Wno-dev >> -DCMAKE_TOOLCHAIN_FILE=~/rfnoc/src/gnuradio/cmake/Toolchains/oe-sdk_cross.cmake >> -DENABLE_GR_WXGUI=OFF -DENABLE_GR_VOCODER=OFF -DENABLE_GR_DTV=OFF >> -DENABLE_GR_ATSC=OFF -DENABLE_DOXYGEN=OFF -DCMAKE_INSTALL_PREFIX=/usr ../ >> -- Build type not specified: defaulting to release. >> -- Build type set to Release. >> -- Extracting version information from git describe... >> -- Compiler Version: arm-oe-linux-gnueabi-gcc (GCC) 7.3.0 >> Copyright (C) 2017 Free Software Foundation, Inc. >> This is free software; see the source for copying conditions. There is NO >> warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR >> PURPOSE. >> -- Compiler Flags: >> /home/jon/rfnoc/oe/sysroots/x86_64-oesdk-linux/usr/bin/arm-oe-linux-gnueabi/arm-oe-linux-gnueabi-gcc:::-O3 >> -DNDEBUG -O2 -pipe -g -feliminate-unused-debug-types -std=gnu99 >> -fvisibility=hidden -Wsign-compare -Wall -Wno-uninitialized >> /home/jon/rfnoc/oe/sysroots/x86_64-oesdk-linux/usr/bin/arm-oe-linux-gnueabi/arm-oe-linux-gnueabi-g++:::-O3 >> -DNDEBUG -O2 -pipe -g -feliminate-unused-debug-types -fvisibility=hidden >> -Wsign-compare -Wall -Wno-uninitialized >> -- ADDING PERF COUNTERS >> -- Building Static Libraries: OFF >> -- Boost version: 1.66.0 >> -- Found the following Boost libraries: >> -- date_time >> -- program_options >> -- filesystem >> -- system >> -- regex >> -- thread >> -- chrono >> -- atomic >> -- >> -- Checking for module SWIG >> -- Found SWIG version 3.0.12. >> -- >> -- The build system will automatically enable all components. >> -- Use -DENABLE_DEFAULT=OFF to disable components by default. >> -- >> -- Configuring python-support support... >> -- Dependency PYTHONLIBS_FOUND = TRUE >> -- Dependency SWIG_FOUND = TRUE >> -- Dependency SWIG_VERSION_CHECK = TRUE >> -- Enabling python-support support. >> -- Override with -DENABLE_PYTHON=ON/OFF >> -- Checking for module 'cppunit' >> -- No package 'cppunit' found >> -- Could NOT find CPPUNIT (missing: CPPUNIT_INCLUDE_DIRS) >> -- >> -- Configuring testing-support support... >> -- Dependency CPPUNIT_FOUND = FALSE >> CMake Error at cmake/Modules/GrComponent.cmake:75 (message): >> user force-enabled testing-support but configuration checked failed >> Call Stack (most recent call first): >> CMakeLists.txt:373 (GR_REGISTER_COMPONENT) >> >> >> -- Configuring incomplete, errors occurred! >> See also >> "/home/jon/rfnoc/src/gnuradio/build-arm/CMakeFiles/CMakeOutput.log". >> See also >> "/home/jon/rfnoc/src/gnuradio/build-arm/CMakeFiles/CMakeError.log". >> >> I have attached the Output and Error logs as well. >> >> In comparing the sysroot/ folders under the rfnoc/oe repository, there is >> a lot of files missing from the 3.15 build that are in the 3.14 build. So >> it appears to be that the SDK is not correct. >> >> Any assistance in getting these issues resolved would be most helpful. >> >> Regards, >> Jon Lockhart >> >
_______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
