On 04/11/2019 01:09 PM, Serge Malo wrote:
Hello Marcus,
We swapepd the d/b of our X300, and the problem followed the d/b.
See below the results of uhd_usrp_probe.
Could it "simply" be a corrupted or badly programmed eeprom?
Thanks,
Serge
My inclination would be to return it under RMA.
inux; GNU C++ version 7.3.0; Boost_106501;
UHD_003.010.003.v3.10.3.0-0-gef157678
-- X300 initialization sequence...
-- Determining maximum frame size... 8000 bytes.
-- Setup basic communication...
-- Loading values from EEPROM...
-- Setup RF frontend clocking...
-- Radio 1x clock:200
-- Detecting internal GPSDO.... No GPSDO found
-- [DMA FIFO] Running BIST for FIFO 0... pass (Throughput: 1298.9MB/s)
-- [DMA FIFO] Running BIST for FIFO 1... pass (Throughput: 1301.2MB/s)
-- [RFNoC Radio] Performing register loopback test... pass
-- [RFNoC Radio] Performing register loopback test... pass
-- [RFNoC Radio] Performing register loopback test... pass
-- [RFNoC Radio] Performing register loopback test... pass
-- Performing timer loopback test... pass
-- Performing timer loopback test... pass
_____________________________________________________
/
| Device: X-Series Device
| _____________________________________________________
| /
| | Mboard: X300
| | revision: 11
| | revision_compat: 7
| | product: 30817
| | mac-addr0: 00:80:2f:24:a1:ee
| | mac-addr1: 00:80:2f:24:a1:ef
| | gateway: 192.168.10.1
| | ip-addr0: 192.168.10.2
| | subnet0: 255.255.255.0
| | ip-addr1: 192.168.20.2
| | subnet1: 255.255.255.0
| | ip-addr2: 192.168.30.2
| | subnet2: 255.255.255.0
| | ip-addr3: 192.168.40.2
| | subnet3: 255.255.255.0
| | serial: 3185E4E
| | FW Version: 5.1
| | FPGA Version: 33.0
| | RFNoC capable: Yes
| |
| | Time sources: internal, external, gpsdo
| | Clock sources: internal, external, gpsdo
| | Sensors: ref_locked
| | _____________________________________________________
| | /
*| | | RX Dboard: A*
*| | | _____________________________________________________*
*| | | /*
*| | | | RX Frontend: 0*
*| | | | Name: Unknown (0xffff) - 0*
*| | | | Antennas: *
*| | | | Sensors: *
*| | | | Freq range: 0.000 to 0.000 MHz*
*| | | | Gain Elements: None*
*| | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz*
*| | | | Connection Type: IQ*
*| | | | Uses LO offset: No*
*| | | _____________________________________________________*
*| | | /*
*| | | | RX Codec: A*
*| | | | Name: ads62p48*
*| | | | Gain range digital: 0.0 to 6.0 step 0.5 dB*
| | _____________________________________________________
| | /
| | | RX Dboard: B
| | | ID: UBX-160 v2 (0x007e)
| | | Serial: 31853D5
| | | _____________________________________________________
| | | /
| | | | RX Frontend: 0
| | | | Name: UBX RX
| | | | Antennas: TX/RX, RX2, CAL
| | | | Sensors: lo_locked
| | | | Freq range: 10.000 to 6000.000 MHz
| | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
| | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | RX Codec: B
| | | | Name: ads62p48
| | | | Gain range digital: 0.0 to 6.0 step 0.5 dB
| | _____________________________________________________
| | /
*| | | TX Dboard: A*
*| | | ID: UBX-160 v2 (0x007d)*
*| | | Serial: 31853CC*
*| | | _____________________________________________________*
*| | | /*
*| | | | TX Frontend: 0*
*| | | | Name: UBX-160 v2 (0x007d) - 0*
*| | | | Antennas: *
*| | | | Sensors: *
*| | | | Freq range: 0.000 to 0.000 MHz*
*| | | | Gain Elements: None*
*| | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz*
*| | | | Connection Type: IQ*
*| | | | Uses LO offset: No*
*| | | _____________________________________________________*
*| | | /*
*| | | | TX Codec: A*
*| | | | Name: ad9146*
*| | | | Gain Elements: None*
| | _____________________________________________________
| | /
| | | TX Dboard: B
| | | ID: UBX-160 v2 (0x007d)
| | | Serial: 31853D5
| | | _____________________________________________________
| | | /
| | | | TX Frontend: 0
| | | | Name: UBX TX
| | | | Antennas: TX/RX, CAL
| | | | Sensors: lo_locked
| | | | Freq range: 10.000 to 6000.000 MHz
| | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
| | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz
| | | | Connection Type: QI
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | TX Codec: B
| | | | Name: ad9146
| | | | Gain Elements: None
| | _____________________________________________________
| | /
| | | RFNoC blocks on this device:
| | |
| | | * DmaFIFO_0
| | | * Radio_0
| | | * Radio_1
| | | * DDC_0
| | | * DDC_1
| | | * DUC_0
| | | * DUC_1
Le jeu. 11 avr. 2019, à 11 h 29, Marcus D. Leech via USRP-users
<usrp-users@lists.ettus.com <mailto:usrp-users@lists.ettus.com>> a écrit :
On 04/11/2019 10:40 AM, Serge Malo via USRP-users wrote:
Hi all,
I am assembling a few X300s with UBX-160 d/b. One of them is
giving me troubles with a UBX-160 v2 d/b. The result from
uhd_usrp_probe can be found below.
Results from other X300s are normal.
We have physically disconnected and reconnected the problematic
d/b, but we still have the same results.
Is there something else I can try, or should I send the board
back for RMA?
Thanks,
Serge
If you use one of the other, known-to-work DBs in this
"problematic" X310, does it work?
Just trying to distinguish the case where the slot in the X310 is
bad, vs bad daughterboard.
linux; GNU C++ version 7.3.0; Boost_106501;
UHD_003.010.003.v3.10.3.0-0-gef157678
-- X300 initialization sequence...
-- Determining maximum frame size... 8000 bytes.
-- Setup basic communication...
-- Loading values from EEPROM...
-- Setup RF frontend clocking...
-- Radio 1x clock:200
-- [DMA FIFO] Running BIST for FIFO 0... pass (Throughput:
1300.1MB/s)
-- [DMA FIFO] Running BIST for FIFO 1... pass (Throughput:
1309.8MB/s)
-- [RFNoC Radio] Performing register loopback test... pass
-- [RFNoC Radio] Performing register loopback test... pass
-- [RFNoC Radio] Performing register loopback test... pass
-- [RFNoC Radio] Performing register loopback test... pass
-- Performing timer loopback test... pass
-- Performing timer loopback test... pass
_____________________________________________________
/
| Device: X-Series Device
| _____________________________________________________
| /
| | Mboard: X300
| | revision: 11
| | revision_compat: 7
| | product: 30817
| | mac-addr0: 00:80:2f:24:a1:ee
| | mac-addr1: 00:80:2f:24:a1:ef
| | gateway: 192.168.10.1
| | ip-addr0: 192.168.10.2
| | subnet0: 255.255.255.0
| | ip-addr1: 192.168.20.2
| | subnet1: 255.255.255.0
| | ip-addr2: 192.168.30.2
| | subnet2: 255.255.255.0
| | ip-addr3: 192.168.40.2
| | subnet3: 255.255.255.0
| | serial: 3185E4E
| | FW Version: 5.1
| | FPGA Version: 33.0
| | RFNoC capable: Yes
| |
| | Time sources: internal, external, gpsdo
| | Clock sources: internal, external, gpsdo
| | Sensors: ref_locked
| | _____________________________________________________
| | /
| | | RX Dboard: A
| | | ID: UBX-160 v2 (0x007e)
| | | Serial: 31853D5
| | | _____________________________________________________
| | | /
| | | | RX Frontend: 0
| | | | Name: UBX RX
| | | | Antennas: TX/RX, RX2, CAL
| | | | Sensors: lo_locked
| | | | Freq range: 10.000 to 6000.000 MHz
| | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
| | | | Bandwidth range: 160000000.0 to 160000000.0 step
0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | RX Codec: A
| | | | Name: ads62p48
| | | | Gain range digital: 0.0 to 6.0 step 0.5 dB
| | _____________________________________________________
| | /
*| | | RX Dboard: B*
*| | | _____________________________________________________*
*| | | /*
*| | | | RX Frontend: 0*
*| | | | Name: Unknown (0xffff) - 0*
*| | | | Antennas: *
*| | | | Sensors: *
*| | | | Freq range: 0.000 to 0.000 MHz*
*| | | | Gain Elements: None*
*| | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz*
*| | | | Connection Type: IQ*
*| | | | Uses LO offset: No*
*| | | _____________________________________________________*
*| | | /*
*| | | | RX Codec: B*
*| | | | Name: ads62p48*
*| | | | Gain range digital: 0.0 to 6.0 step 0.5 dB*
| | _____________________________________________________
| | /
| | | TX Dboard: A
| | | ID: UBX-160 v2 (0x007d)
| | | Serial: 31853D5
| | | _____________________________________________________
| | | /
| | | | TX Frontend: 0
| | | | Name: UBX TX
| | | | Antennas: TX/RX, CAL
| | | | Sensors: lo_locked
| | | | Freq range: 10.000 to 6000.000 MHz
| | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
| | | | Bandwidth range: 160000000.0 to 160000000.0 step
0.0 Hz
| | | | Connection Type: QI
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | TX Codec: A
| | | | Name: ad9146
| | | | Gain Elements: None
| | _____________________________________________________
| | /
*| | | TX Dboard: B*
*| | | ID: UBX-160 v2 (0x007d)*
*| | | Serial: 31853CC*
*| | | _____________________________________________________*
*| | | /*
*| | | | TX Frontend: 0*
*| | | | Name: UBX-160 v2 (0x007d) - 0*
*| | | | Antennas: *
*| | | | Sensors: *
*| | | | Freq range: 0.000 to 0.000 MHz*
*| | | | Gain Elements: None*
*| | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz*
*| | | | Connection Type: IQ*
*| | | | Uses LO offset: No*
*| | | _____________________________________________________*
*| | | /*
*| | | | TX Codec: B*
*| | | | Name: ad9146*
*| | | | Gain Elements: None*
| | _____________________________________________________
| | /
| | | RFNoC blocks on this device:
| | |
| | | * DmaFIFO_0
| | | * Radio_0
| | | * Radio_1
| | | * DDC_0
| | | * DDC_1
| | | * DUC_0
| | | * DUC_1
_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com <mailto:USRP-users@lists.ettus.com>
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com <mailto:USRP-users@lists.ettus.com>
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
