Hello Marcus, We swapepd the d/b of our X300, and the problem followed the d/b. See below the results of uhd_usrp_probe.
Could it "simply" be a corrupted or badly programmed eeprom? Thanks, Serge inux; GNU C++ version 7.3.0; Boost_106501; UHD_003.010.003.v3.10.3.0-0-gef157678 -- X300 initialization sequence... -- Determining maximum frame size... 8000 bytes. -- Setup basic communication... -- Loading values from EEPROM... -- Setup RF frontend clocking... -- Radio 1x clock:200 -- Detecting internal GPSDO.... No GPSDO found -- [DMA FIFO] Running BIST for FIFO 0... pass (Throughput: 1298.9MB/s) -- [DMA FIFO] Running BIST for FIFO 1... pass (Throughput: 1301.2MB/s) -- [RFNoC Radio] Performing register loopback test... pass -- [RFNoC Radio] Performing register loopback test... pass -- [RFNoC Radio] Performing register loopback test... pass -- [RFNoC Radio] Performing register loopback test... pass -- Performing timer loopback test... pass -- Performing timer loopback test... pass _____________________________________________________ / | Device: X-Series Device | _____________________________________________________ | / | | Mboard: X300 | | revision: 11 | | revision_compat: 7 | | product: 30817 | | mac-addr0: 00:80:2f:24:a1:ee | | mac-addr1: 00:80:2f:24:a1:ef | | gateway: 192.168.10.1 | | ip-addr0: 192.168.10.2 | | subnet0: 255.255.255.0 | | ip-addr1: 192.168.20.2 | | subnet1: 255.255.255.0 | | ip-addr2: 192.168.30.2 | | subnet2: 255.255.255.0 | | ip-addr3: 192.168.40.2 | | subnet3: 255.255.255.0 | | serial: 3185E4E | | FW Version: 5.1 | | FPGA Version: 33.0 | | RFNoC capable: Yes | | | | Time sources: internal, external, gpsdo | | Clock sources: internal, external, gpsdo | | Sensors: ref_locked | | _____________________________________________________ | | / *| | | RX Dboard: A* *| | | _____________________________________________________* *| | | /* *| | | | RX Frontend: 0* *| | | | Name: Unknown (0xffff) - 0* *| | | | Antennas: * *| | | | Sensors: * *| | | | Freq range: 0.000 to 0.000 MHz* *| | | | Gain Elements: None* *| | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz* *| | | | Connection Type: IQ* *| | | | Uses LO offset: No* *| | | _____________________________________________________* *| | | /* *| | | | RX Codec: A* *| | | | Name: ads62p48* *| | | | Gain range digital: 0.0 to 6.0 step 0.5 dB* | | _____________________________________________________ | | / | | | RX Dboard: B | | | ID: UBX-160 v2 (0x007e) | | | Serial: 31853D5 | | | _____________________________________________________ | | | / | | | | RX Frontend: 0 | | | | Name: UBX RX | | | | Antennas: TX/RX, RX2, CAL | | | | Sensors: lo_locked | | | | Freq range: 10.000 to 6000.000 MHz | | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB | | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz | | | | Connection Type: IQ | | | | Uses LO offset: No | | | _____________________________________________________ | | | / | | | | RX Codec: B | | | | Name: ads62p48 | | | | Gain range digital: 0.0 to 6.0 step 0.5 dB | | _____________________________________________________ | | / *| | | TX Dboard: A* *| | | ID: UBX-160 v2 (0x007d)* *| | | Serial: 31853CC* *| | | _____________________________________________________* *| | | /* *| | | | TX Frontend: 0* *| | | | Name: UBX-160 v2 (0x007d) - 0* *| | | | Antennas: * *| | | | Sensors: * *| | | | Freq range: 0.000 to 0.000 MHz* *| | | | Gain Elements: None* *| | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz* *| | | | Connection Type: IQ* *| | | | Uses LO offset: No* *| | | _____________________________________________________* *| | | /* *| | | | TX Codec: A* *| | | | Name: ad9146* *| | | | Gain Elements: None* | | _____________________________________________________ | | / | | | TX Dboard: B | | | ID: UBX-160 v2 (0x007d) | | | Serial: 31853D5 | | | _____________________________________________________ | | | / | | | | TX Frontend: 0 | | | | Name: UBX TX | | | | Antennas: TX/RX, CAL | | | | Sensors: lo_locked | | | | Freq range: 10.000 to 6000.000 MHz | | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB | | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz | | | | Connection Type: QI | | | | Uses LO offset: No | | | _____________________________________________________ | | | / | | | | TX Codec: B | | | | Name: ad9146 | | | | Gain Elements: None | | _____________________________________________________ | | / | | | RFNoC blocks on this device: | | | | | | * DmaFIFO_0 | | | * Radio_0 | | | * Radio_1 | | | * DDC_0 | | | * DDC_1 | | | * DUC_0 | | | * DUC_1 Le jeu. 11 avr. 2019, à 11 h 29, Marcus D. Leech via USRP-users < usrp-users@lists.ettus.com> a écrit : > On 04/11/2019 10:40 AM, Serge Malo via USRP-users wrote: > > Hi all, > > I am assembling a few X300s with UBX-160 d/b. One of them is giving me > troubles with a UBX-160 v2 d/b. The result from uhd_usrp_probe can be found > below. > Results from other X300s are normal. > We have physically disconnected and reconnected the problematic d/b, but > we still have the same results. > Is there something else I can try, or should I send the board back for RMA? > > Thanks, > Serge > > If you use one of the other, known-to-work DBs in this "problematic" X310, > does it work? > > Just trying to distinguish the case where the slot in the X310 is bad, vs > bad daughterboard. > > linux; GNU C++ version 7.3.0; Boost_106501; > UHD_003.010.003.v3.10.3.0-0-gef157678 > > -- X300 initialization sequence... > -- Determining maximum frame size... 8000 bytes. > -- Setup basic communication... > -- Loading values from EEPROM... > -- Setup RF frontend clocking... > -- Radio 1x clock:200 > -- [DMA FIFO] Running BIST for FIFO 0... pass (Throughput: 1300.1MB/s) > -- [DMA FIFO] Running BIST for FIFO 1... pass (Throughput: 1309.8MB/s) > -- [RFNoC Radio] Performing register loopback test... pass > -- [RFNoC Radio] Performing register loopback test... pass > -- [RFNoC Radio] Performing register loopback test... pass > -- [RFNoC Radio] Performing register loopback test... pass > -- Performing timer loopback test... pass > -- Performing timer loopback test... pass > _____________________________________________________ > / > | Device: X-Series Device > | _____________________________________________________ > | / > | | Mboard: X300 > | | revision: 11 > | | revision_compat: 7 > | | product: 30817 > | | mac-addr0: 00:80:2f:24:a1:ee > | | mac-addr1: 00:80:2f:24:a1:ef > | | gateway: 192.168.10.1 > | | ip-addr0: 192.168.10.2 > | | subnet0: 255.255.255.0 > | | ip-addr1: 192.168.20.2 > | | subnet1: 255.255.255.0 > | | ip-addr2: 192.168.30.2 > | | subnet2: 255.255.255.0 > | | ip-addr3: 192.168.40.2 > | | subnet3: 255.255.255.0 > | | serial: 3185E4E > | | FW Version: 5.1 > | | FPGA Version: 33.0 > | | RFNoC capable: Yes > | | > | | Time sources: internal, external, gpsdo > | | Clock sources: internal, external, gpsdo > | | Sensors: ref_locked > | | _____________________________________________________ > | | / > | | | RX Dboard: A > | | | ID: UBX-160 v2 (0x007e) > | | | Serial: 31853D5 > | | | _____________________________________________________ > | | | / > | | | | RX Frontend: 0 > | | | | Name: UBX RX > | | | | Antennas: TX/RX, RX2, CAL > | | | | Sensors: lo_locked > | | | | Freq range: 10.000 to 6000.000 MHz > | | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB > | | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz > | | | | Connection Type: IQ > | | | | Uses LO offset: No > | | | _____________________________________________________ > | | | / > | | | | RX Codec: A > | | | | Name: ads62p48 > | | | | Gain range digital: 0.0 to 6.0 step 0.5 dB > | | _____________________________________________________ > | | / > *| | | RX Dboard: B* > *| | | _____________________________________________________* > *| | | /* > *| | | | RX Frontend: 0* > *| | | | Name: Unknown (0xffff) - 0* > *| | | | Antennas: * > *| | | | Sensors: * > *| | | | Freq range: 0.000 to 0.000 MHz* > *| | | | Gain Elements: None* > *| | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz* > *| | | | Connection Type: IQ* > *| | | | Uses LO offset: No* > *| | | _____________________________________________________* > *| | | /* > *| | | | RX Codec: B* > *| | | | Name: ads62p48* > *| | | | Gain range digital: 0.0 to 6.0 step 0.5 dB* > | | _____________________________________________________ > | | / > | | | TX Dboard: A > | | | ID: UBX-160 v2 (0x007d) > | | | Serial: 31853D5 > | | | _____________________________________________________ > | | | / > | | | | TX Frontend: 0 > | | | | Name: UBX TX > | | | | Antennas: TX/RX, CAL > | | | | Sensors: lo_locked > | | | | Freq range: 10.000 to 6000.000 MHz > | | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB > | | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz > | | | | Connection Type: QI > | | | | Uses LO offset: No > | | | _____________________________________________________ > | | | / > | | | | TX Codec: A > | | | | Name: ad9146 > | | | | Gain Elements: None > | | _____________________________________________________ > | | / > *| | | TX Dboard: B* > *| | | ID: UBX-160 v2 (0x007d)* > *| | | Serial: 31853CC* > *| | | _____________________________________________________* > *| | | /* > *| | | | TX Frontend: 0* > *| | | | Name: UBX-160 v2 (0x007d) - 0* > *| | | | Antennas: * > *| | | | Sensors: * > *| | | | Freq range: 0.000 to 0.000 MHz* > *| | | | Gain Elements: None* > *| | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz* > *| | | | Connection Type: IQ* > *| | | | Uses LO offset: No* > *| | | _____________________________________________________* > *| | | /* > *| | | | TX Codec: B* > *| | | | Name: ad9146* > *| | | | Gain Elements: None* > | | _____________________________________________________ > | | / > | | | RFNoC blocks on this device: > | | | > | | | * DmaFIFO_0 > | | | * Radio_0 > | | | * Radio_1 > | | | * DDC_0 > | | | * DDC_1 > | | | * DUC_0 > | | | * DUC_1 > > > > > _______________________________________________ > USRP-users mailing > listUSRP-users@lists.ettus.comhttp://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com > > > _______________________________________________ > USRP-users mailing list > USRP-users@lists.ettus.com > http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com >
_______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
