Hi all, I have been using the usrp N210 and RFX900 daughterboard, and it was working well two days ago, but after I updated my macports(and all the ports including uhd and gnuradio), the device can't work anymore.
For now I can detect the usrp (when run uhd_detect_devices command), but when I run uhd_usrp_probe or some other commands(like gqrx or gnuradio application), I get this kind of error/warning message: At first it gave error: [INFO] [UHD] Mac OS; Clang version 9.0.0 (clang-900.0.39.2); Boost_106600; UHD_3.13.0.1-MacPorts-Release [INFO] [USRP2] Opening a USRP2/N-Series device... [INFO] [USRP2] Current recv frame size: 1472 bytes [INFO] [USRP2] Current send frame size: 1472 bytes [INFO] [USRP2] Detecting internal GPSDO.... [INFO] [GPS] No GPSDO found [ERROR] [DBMGR] The daughterboard manager encountered a recoverable error in init. Loading the "unknown" daughterboard implementations to continue. The daughterboard cannot operate until this error is resolved. LookupError: KeyError: key "0" not found in dict(i, N14adf4360_regs_t17prescaler_value_tE) _____________________________________________________ / | Device: USRP2 / N-Series Device | _____________________________________________________ | / | | Mboard: N210r4 | | hardware: 2577 | | mac-addr: 00:80:2f:19:89:31 | | ip-addr: 192.168.10.2 | | subnet: 255.255.255.255 | | gateway: 255.255.255.255 | | gpsdo: none | | serial: 30757BE | | FW Version: 12.4 | | FPGA Version: 11.1 | | | | Time sources: none, external, _external_, mimo | | Clock sources: internal, external, mimo | | Sensors: mimo_locked, ref_locked | | _____________________________________________________ | | / | | | RX DSP: 0 | | | | | | Freq range: -50.000 to 50.000 MHz | | _____________________________________________________ | | / | | | RX DSP: 1 | | | | | | Freq range: -50.000 to 50.000 MHz | | _____________________________________________________ | | / | | | RX Dboard: A | | | ID: RFX900 (0x0025) | | | Serial: E1R14UBR9 | | | _____________________________________________________ | | | / | | | | RX Frontend: 0 | | | | Name: Unknown (0xffff) - 0 | | | | Antennas: | | | | Sensors: | | | | Freq range: 0.000 to 0.000 MHz | | | | Gain Elements: None | | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz | | | | Connection Type: IQ | | | | Uses LO offset: No | | | _____________________________________________________ | | | / | | | | RX Codec: A | | | | Name: ads62p44 | | | | Gain range digital: 0.0 to 6.0 step 0.5 dB | | | | Gain range fine: 0.0 to 0.5 step 0.1 dB | | _____________________________________________________ | | / | | | TX DSP: 0 | | | | | | Freq range: -200.000 to 200.000 MHz | | _____________________________________________________ | | / | | | TX Dboard: A | | | ID: RFX900 (0x0029) | | | Serial: E1R14UBR9 | | | _____________________________________________________ | | | / | | | | TX Frontend: 0 | | | | Name: Unknown (0xffff) - 0 | | | | Antennas: | | | | Sensors: | | | | Freq range: 0.000 to 0.000 MHz | | | | Gain Elements: None | | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz | | | | Connection Type: IQ | | | | Uses LO offset: No | | | _____________________________________________________ | | | / | | | | TX Codec: A | | | | Name: ad9777 | | | | Gain Elements: None After I tried to reseat the daughterboard and add 8 screws to the daughterboard, the error becomes warning: [INFO] [UHD] Mac OS; Clang version 9.0.0 (clang-900.0.39.2); Boost_106600; UHD_3.13.0.1-MacPorts-Release [INFO] [USRP2] Opening a USRP2/N-Series device... [INFO] [USRP2] Current recv frame size: 1472 bytes [INFO] [USRP2] Current send frame size: 1472 bytes [WARNING] [DBMGR] Unknown transceiver board ID combination. Is your daughter-board mounted properly? RX dboard ID: RFX900 (0x0025) TX dboard ID: RFX900 (0x0025) _____________________________________________________ / | Device: USRP2 / N-Series Device | _____________________________________________________ | / | | Mboard: N210r4 | | hardware: 2577 | | mac-addr: 00:80:2f:19:89:31 | | ip-addr: 192.168.10.2 | | subnet: 255.255.255.255 | | gateway: 255.255.255.255 | | gpsdo: none | | serial: 30757BE | | FW Version: 12.4 | | FPGA Version: 11.1 | | | | Time sources: none, external, _external_, mimo | | Clock sources: internal, external, mimo | | Sensors: mimo_locked, ref_locked | | _____________________________________________________ | | / | | | RX DSP: 0 | | | | | | Freq range: -50.000 to 50.000 MHz | | _____________________________________________________ | | / | | | RX DSP: 1 | | | | | | Freq range: -50.000 to 50.000 MHz | | _____________________________________________________ | | / | | | RX Dboard: A | | | ID: RFX900 (0x0025) | | | Serial: E1R14UBR9 | | | _____________________________________________________ | | | / | | | | RX Frontend: 0 | | | | Name: RFX900 (0x0025) - 0 | | | | Antennas: | | | | Sensors: | | | | Freq range: 0.000 to 0.000 MHz | | | | Gain Elements: None | | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz | | | | Connection Type: IQ | | | | Uses LO offset: No | | | _____________________________________________________ | | | / | | | | RX Codec: A | | | | Name: ads62p44 | | | | Gain range digital: 0.0 to 6.0 step 0.5 dB | | | | Gain range fine: 0.0 to 0.5 step 0.1 dB | | _____________________________________________________ | | / | | | TX DSP: 0 | | | | | | Freq range: -200.000 to 200.000 MHz | | _____________________________________________________ | | / | | | TX Dboard: A | | | ID: RFX900 (0x0025) | | | Serial: E1R14UBR9 | | | _____________________________________________________ | | | / | | | | TX Frontend: 0 | | | | Name: RFX900 (0x0025) - 0 | | | | Antennas: | | | | Sensors: | | | | Freq range: 0.000 to 0.000 MHz | | | | Gain Elements: None | | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz | | | | Connection Type: IQ | | | | Uses LO offset: No | | | _____________________________________________________ | | | / | | | | TX Codec: A | | | | Name: ad9777 | | | | Gain Elements: None The version I'm using now is GNU Radio 3.7.13.4, and the uhd version is 3.13.0.1. The previous working uhd version is 3.010.001.001, but it still doesn't work even if we switch back to the previous version. Any suggestions or advices?? Thanks for the help! Best, Shirley
_______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
