Hi, I am allowed to do that, but how am I able to do that using ISE 14.7 together with the USRP B210?
Thanks in advance! ________________________________________ From: Ian Buckley [i...@ionconcepts.com] Sent: 07 April 2018 03:19 To: Yeo Jin Kuang Alvin (IA) Cc: usrp-users@lists.ettus.com Subject: Re: [USRP-users] USRP B210 Making a hardware DDS to generate a chirp in the FPGA is easy, extremely so if you reuse the Ettus code that interfaces the B210 to AD3961 with correct timing. What is very hard in what you propose, is controlling the AD9361 from within the FPGA without an external host. There is a *lot* of configuration functionality that needs to be captured. Are the constraints of your project such that you are not allowed to have a host connected to USB? On Apr 5, 2018, at 7:57 PM, Yeo Jin Kuang Alvin (IA) via USRP-users <usrp-users@lists.ettus.com<mailto:usrp-users@lists.ettus.com>> wrote: From: Yeo Jin Kuang Alvin (IA) Sent: Friday, 6 April 2018 10:55 AM To: 'Neel Pandeya' Subject: RE: [USRP-users] USRP B210 Hi Neel, I am trying to output a chirp signal by creating a DDS in the FPGA using Xilinx ISE 14.7. The code is done from scratch and created a SPI module in the FPGA to control the AD9361 to output the signal. Set up the constraints file gotten from ettus research in git. This are my usual steps: 1) uhd_usrp_probe - -args=”master_clock_rate=40e6” (I am setting to 40MHz as I am using the codec_main_clk in the AD9361 as my main clock, not sure if this is right but simulation/chipscope seems fine ) 2) Opened Xilinx ISE 14.7 3) Generate .bit file 4) Run on IMPACT using JTAG cable 5) Program the file But I couldn’t get any signal out from the transmitter, there is no software C++ or GNU Radio involve. Just solely on FPGA as I am task to create a chirp signal using FPGA. I might have missed out something, like configuration or concept is not right. Just not sure where and how. Thank you in advance! From: Neel Pandeya [mailto:neel.pand...@ettus.com] Sent: Friday, 6 April 2018 10:34 AM To: Yeo Jin Kuang Alvin (IA) Cc: usrp-users@lists.ettus.com<mailto:usrp-users@lists.ettus.com> Subject: Re: [USRP-users] USRP B210 Hello Yeo Jin Kuang Alvin: If you're modifying the FPGA, then there will likely be a corresponding modification needed on the host-side, especially for something as significant as starting a transmit stream and/or controlling the AD9361 in some way. We'll need much more detail in order to be able to help further. What changes did you make to the FPGA? What exactly are you trying to do overall? --Neel Pandeya On 5 April 2018 at 18:07, Yeo Jin Kuang Alvin (IA) via USRP-users <usrp-users@lists.ettus.com<mailto:usrp-users@lists.ettus.com>> wrote: Hi everyone, I have tried to program the Spartan 6 FPGA using Xilinx 14.7 to send out a signal and to control the AD9361. However, I couldn’t get an output out from the transmitter. Can I just solely on FPGA or must I use the API for the USRP B210? What are the steps and procedures I have to do to configure the board, I just feel that I might miss out some important steps. Thank you in advance! _______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com<mailto:USRP-users@lists.ettus.com> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com _______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com<mailto:USRP-users@lists.ettus.com> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com _______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
