Dan Lukes wrote:
> Miroslav Lachman napsal/wrote, On 12/27/07 22:11:
>
>>No ja zrovna pred par dny instaloval FreeBSD 7 na nejaky Intel
>>(desktopovy board) a to melo snad ICH9 a system na nem nenasel disky v
>>rezimu AHCI, pouze v rezimu IDE kompatibility.
>
>
> To me trochu prekvapuje, protoze moje "masina na hrani" ma sobe
> 6.3-PRERELEASE a disky nasla - pokud se to da soudit z toho, ze z ni
> zrovna pisu:
>
> -----------------------------------
> [EMAIL PROTECTED]:31:2:
> class=0x010601 card=0x73451462 chip=0x29228086 rev=0x02 hdr=0x00
> vendor = 'Intel Corporation'
> device = '82801IB/IR/IH (ICH9 Family) 6 port SATA AHCI Controller'
> class = mass storage
> port 0xa000-0xa007,0x9c00-0x9c03,0x9880-0x9887,
> 0x9800-0x9803,0x9480-0x949f
> mem 0xf9fff000-0xf9fff7ff
> irq 19 at device 31.2 on pci0
> AHCI Version 01.20 controller with 6 ports detected
> ata4: <ATA channel 0> on atapci1
> ata5: <ATA channel 1> on atapci1
> ata6: <ATA channel 2> on atapci1
> ata7: <ATA channel 3> on atapci1
> ata8: <ATA channel 4> on atapci1
> ata9: <ATA channel 5> on atapci1
>
> ad12: 239372MB <WDC WD2500YS-01SHB0 20.06C03> at ata6-master SATA300
> Trying to mount root from ufs:/dev/ad12s2a
> -----------------------------------
>
> Ale ICH9 existuji v nekolika modifikacich - takze by vysvetlenim mohlo
> byt to, ze mas nejaky jiny, nepodporovany. Varianta, ze by tu byl nejaky
> radic podporovany v 6.3 ale nepodporovany v 7.0 mi nepripada pravdepodobna.
[EMAIL PROTECTED]:0:31:2: class=0x01018f card=0x82771043 chip=0x29208086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) 4 port Serial ATA Storage
Controller 1'
class = mass storage
subclass = ATA
atapci1: <Intel ICH9 SATA300 controller> port
0xb000-0xb007,0xac00-0xac03,0xa880-0xa887,0xa800-0xa803,0xa480-0xa48f,0xa400-0xa40f
irq 22 at device 31.2 on pci
0
atapci1: [ITHREAD]
ata5: <ATA channel 0> on atapci1
ata5: [ITHREAD]
ata6: <ATA channel 1> on atapci1
ata6: [ITHREAD]
ad10: 238475MB <WDC WD2500AVJS-63WDA0 12.01B02> at ata5-master SATA150
ad12: 238475MB <WDC WD2500AVJS-63WDA0 12.01B02> at ata6-master SATA150
Ted kdyz to znovu vidim takhle pred sebou, tak uz asi i tusim, kde je
problem - firma, co ten "server" sestavila, nechala disky najumperovane
na SATA150, nebo to jsou primo SATA I disky a tam je mozne, ze to s AHCI
nefunguje (ale nejsem si tim jisty, kdekoliv jinde mam AHCI a SATA II
[SATA300] disky)
# uname -srmi
FreeBSD 7.0-BETA4 i386 GENERIC
Mirek
--
FreeBSD mailing list (users-l@freebsd.cz)
http://www.freebsd.cz/listserv/listinfo/users-l
