Regarding this, I don’t recall seeing a reply to my query about whether you still need to disable error messages when building a standalone. Hopefully this has been fixed, but …
Best, Bill William A. Prothero, PhD Prof Emeritus, Dept of Earth Science University of California, Santa Barbara > On Feb 1, 2022, at 6:59 AM, matthias rebbe via use-livecode > <use-livecode@lists.runrev.com> wrote: > > Mark, > > where are you saving the standalone to? > Any chance that the target folder is on iCloud drive. E.g. Desktop or > Documents folder? > > I had similar problems in the past when i built the standalone directly on > the Desktop or Documents folder which were both synchronized with iCloud > Drive. I just cannot remember the correct error message. Sometimes the build > process was successful and sometimes it was aborted. > I could solve this to select a target folder outside of iCloud Drive. > Btw. building the standalone in a Dropbox folder works w/o problems. > > Matthias > >> Am 01.02.2022 um 11:47 schrieb Mark Smith via use-livecode >> <use-livecode@lists.runrev.com>: >> >> Hi Panos, >> >> I did not change anything between attempts, just one right after the other. >> I guess I was observing this in RC2 and just persisted and it seemed to work >> on the 2nd or 3rd attempt. For good measure I just took the same stack and >> was able to build and install two more times without incident so it’s >> definitely not a repeatable problem and as yet I have no formula or >> hypothesis as to what might be causing it. I’ll keep an eye on it and log >> any similar problems I run across. >> >> Mark >> >> >>>> On Feb 1, 2022, at 10:23 AM, panagiotis m via use-livecode >>>> <use-livecode@lists.runrev.com> wrote: >>> >>> Hello Mark, >>> >>> I have not seen this before. Did anything change in your stack (used a >>> different provisioning profile or changed anything in the iOS settings) or >>> in the iOS device until the successful 3rd attempt? >>> >>> I cannot remember of anything that we changed in the 9.6.6 release cycle >>> that could have caused this behavior. >>> >>> Kind regards, >>> Panos >>> >>> On Tue, 1 Feb 2022 at 12:14, Mark Smith via use-livecode < >>> use-livecode@lists.runrev.com> wrote: >>> >>>> I just wanted to flag this issue. I am currently using the new release >>>> version of 9.6.6 although I did have similar problems with RC2 as well. >>>> This morning I took a stack I had previously built and successfully >>>> installed (using Development/Test Target -> iPhone) and tried installing >>>> it. The first time the app went through what appeared to be all the build >>>> steps but did not install the app. The 2nd time it went through all of the >>>> steps and then reported “Unknown Error” and the 3rd time it built and >>>> installed the app correctly. I’ve not noticed behaviour like this in >>>> previous versions. At the moment I have no hypothesis about what might be >>>> going on. >>>> >>>> Mark >>>> >>>> >>>> _______________________________________________ >>>> use-livecode mailing list >>>> use-livecode@lists.runrev.com >>>> Please visit this url to subscribe, unsubscribe and manage your >>>> subscription preferences: >>>> http://lists.runrev.com/mailman/listinfo/use-livecode >>>> >>> _______________________________________________ >>> use-livecode mailing list >>> use-livecode@lists.runrev.com >>> Please visit this url to subscribe, unsubscribe and manage your >>> subscription preferences: >>> http://lists.runrev.com/mailman/listinfo/use-livecode >> >> >> _______________________________________________ >> use-livecode mailing list >> use-livecode@lists.runrev.com >> Please visit this url to subscribe, unsubscribe and manage your subscription >> preferences: >> http://lists.runrev.com/mailman/listinfo/use-livecode > > > _______________________________________________ > use-livecode mailing list > use-livecode@lists.runrev.com > Please visit this url to subscribe, unsubscribe and manage your subscription > preferences: > http://lists.runrev.com/mailman/listinfo/use-livecode _______________________________________________ use-livecode mailing list use-livecode@lists.runrev.com Please visit this url to subscribe, unsubscribe and manage your subscription preferences: http://lists.runrev.com/mailman/listinfo/use-livecode