The i.MX53 has MXC_H*_UCTRL_H*_OC_DIS_BIT bits to disable the oc pin.
Signed-off-by: Benoît Thébaudeau <benoit.thebaud...@advansee.com>
Cc: Marek Vasut <ma...@denx.de>
Cc: Stefano Babic <sba...@denx.de>
---
.../drivers/usb/host/ehci-mx5.c | 25 ++++++++++++++++++++
1 file changed, 25 insertions(+)
diff --git u-boot-usb-76454b2.orig/drivers/usb/host/ehci-mx5.c
u-boot-usb-76454b2/drivers/usb/host/ehci-mx5.c
index 8e42e56..7da1398 100644
--- u-boot-usb-76454b2.orig/drivers/usb/host/ehci-mx5.c
+++ u-boot-usb-76454b2/drivers/usb/host/ehci-mx5.c
@@ -32,12 +32,14 @@
#define MXC_OTG_OFFSET 0
#define MXC_H1_OFFSET 0x200
#define MXC_H2_OFFSET 0x400
+#define MXC_H3_OFFSET 0x600
#define MXC_USBCTRL_OFFSET 0
#define MXC_USB_PHY_CTR_FUNC_OFFSET 0x8
#define MXC_USB_PHY_CTR_FUNC2_OFFSET 0xc
#define MXC_USB_CTRL_1_OFFSET 0x10
#define MXC_USBH2CTRL_OFFSET 0x14
+#define MXC_USBH3CTRL_OFFSET 0x18
/* USB_CTRL */
#define MXC_OTG_UCTRL_OWIE_BIT (1 << 27) /* OTG wakeup intr
enable */
@@ -51,10 +53,16 @@
#define MXC_H1_OC_DIS_BIT (1 << 5) /* UH1 Disable
Overcurrent Event */
/* USBH2CTRL */
+#define MXC_H2_UCTRL_H2_OC_DIS_BIT (1 << 30)
#define MXC_H2_UCTRL_H2UIE_BIT (1 << 8)
#define MXC_H2_UCTRL_H2WIE_BIT (1 << 7)
#define MXC_H2_UCTRL_H2PM_BIT (1 << 4)
+/* USBH3CTRL */
+#define MXC_H3_UCTRL_H3_OC_DIS_BIT (1 << 30)
+#define MXC_H3_UCTRL_H3UIE_BIT (1 << 8)
+#define MXC_H3_UCTRL_H3WIE_BIT (1 << 7)
+
/* USB_CTRL_1 */
#define MXC_USB_CTRL_UH1_EXT_CLK_EN (1 << 25)
@@ -196,9 +204,26 @@ int mxc_set_usbcontrol(int port, unsigned int flags)
else
v |= MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask used */
#endif
+#ifdef CONFIG_MX53
+ if (flags & MXC_EHCI_POWER_PINS_ENABLED)
+ v &= ~MXC_H2_UCTRL_H2_OC_DIS_BIT; /* OC is used */
+ else
+ v |= MXC_H2_UCTRL_H2_OC_DIS_BIT; /* OC is not used */
+#endif
__raw_writel(v, usbother_base + MXC_USBH2CTRL_OFFSET);
break;
+#ifdef CONFIG_MX53
+ case 3: /* Host 3 ULPI */
+ v = __raw_readl(usbother_base + MXC_USBH3CTRL_OFFSET);
+ if (flags & MXC_EHCI_POWER_PINS_ENABLED)
+ v &= ~MXC_H3_UCTRL_H3_OC_DIS_BIT; /* OC is used */
+ else
+ v |= MXC_H3_UCTRL_H3_OC_DIS_BIT; /* OC is not used */
+
+ __raw_writel(v, usbother_base + MXC_USBH3CTRL_OFFSET);
+ break;
+#endif
}
return ret;
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
