On 28/06/2012 22:36, Philippe Reynes wrote:
> Signed-off-by: Philippe Reynes <trem...@yahoo.fr>
> Signed-off-by: Eric Jarrige <eric.jarr...@armadeus.org>
> ---

Hi Philippe,


> + *
> + */
> +#include <common.h>
> +
> +#if defined(CONFIG_FPGA)

Maybe you can drop this and compiling this file only if CONFIG_FPGA is
set, changing your Makefile

> +
> +#define GPIO_PORT(x)  ((x & GPIO_PORT_MASK) >> GPIO_PORT_SHIFT)
> +#define GPIO_SET(x)   writel(readl(&gpregs->port[GPIO_PORT(x)].dr) | \
> +             (1 << (x & GPIO_PIN_MASK)), &gpregs->port[GPIO_PORT(x)].dr)
> +
> +/* (DR(GPIO_PORT(x)) |= (1<<(x & GPIO_PIN_MASK))) */
> +#define GPIO_CLEAR(x) writel(readl(&gpregs->port[GPIO_PORT(x)].dr) & \
> +             ~(1 << (x & GPIO_PIN_MASK)), &gpregs->port[GPIO_PORT(x)].dr)
> +/* (DR(GPIO_PORT(x)) &= ~(1<<(x & GPIO_PIN_MASK))) */
> +#define GPIO_WRITE(x, y) (y ? GPIO_SET(x) : GPIO_CLEAR(x))
> +#define GPIO_READ(x) ((readl(&gpregs->port[GPIO_PORT(x)].ssr) & \
> +             (1 << (x & GPIO_PIN_MASK))) >> (x & GPIO_PIN_MASK))

No, we have in u-boot a GPIO API to access the GPIOs. Check
./include/asm-generic/gpio.h, and the implementation for other i.MX SOCs.


> +#ifdef FPGA_DEBUG
> +#define      PRINTF(fmt, args...)    printf(fmt, ##args)
> +#else
> +#define      PRINTF(fmt, args...)
> +#endif

Do not set your special version - use DEBUG instead

> +
> +/* Note that these are pointers to code that is in Flash.  They will be
> + * relocated at runtime.
> + * Spartan2 code is used to download our Spartan 3 :) code is compatible.
> + * Just take care about the file size
> +*/

Wrong multiline comment - it should be like this:

/*
 * Part of your multiline
 * comment
 */

Please check this issue everywhere in your code

> +Xilinx_Spartan3_Slave_Parallel_fns fpga_fns = {
> +     fpga_pre_fn,
> +     fpga_pgm_fn,
> +     fpga_init_fn,
> +     NULL,
> +     fpga_done_fn,
> +     fpga_clk_fn,
> +     fpga_cs_fn,
> +     fpga_wr_fn,
> +     fpga_rdata_fn,
> +     fpga_wdata_fn,
> +     fpga_busy_fn,
> +     fpga_abort_fn,
> +     fpga_post_fn,
> +};
> +
> +Xilinx_desc fpga[CONFIG_FPGA_COUNT] = {
> +     {Xilinx_Spartan3,
> +      slave_parallel,
> +      1196128l/8,
> +      (void *) &fpga_fns,
> +      0}
> +};
> +
> +/*
> + * nitialize GPIO port B before download

initialize

Best regards,
Stefano Babic


-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sba...@denx.de
=====================================================================

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Reply via email to