Hi Aditya,
On Mon, Dec 03, 2018 at 09:39:56AM +0700, Aditya Prayoga wrote:
> On Fri, Nov 30, 2018 at 3:25 PM Stefan Roese <s...@denx.de> wrote:
> > On 30.11.18 09:14, Aditya Prayoga wrote:
> > > On Fri, Nov 30, 2018 at 2:44 PM Stefan Roese <s...@denx.de> wrote:
> > >>
> > >> On 30.11.18 03:54, Aditya Prayoga wrote:
> > >>> Similar to Clearfog rev 2.1, GPIO 19 also used to reset onboard ethernet
> > >>> PHY.
> > >>>
> > >>> Signed-off-by: Aditya Prayoga <adi...@kobol.io>
> > >>> ---
> > >>> v2:
> > >>> * Use generic gpio_* API (Baruch Siach)
> > >>> ---
> > >>> board/kobol/helios4/helios4.c | 31 +++++++++++++++++++++++++++++++
> > >>> 1 file changed, 31 insertions(+)
> > >>>
> > >>> diff --git a/board/kobol/helios4/helios4.c
> > >>> b/board/kobol/helios4/helios4.c
> > >>> index 37c46a5..e535d7b 100644
> > >>> --- a/board/kobol/helios4/helios4.c
> > >>> +++ b/board/kobol/helios4/helios4.c
> > >>> @@ -8,6 +8,7 @@
> > >>> #include <i2c.h>
> > >>> #include <miiphy.h>
> > >>> #include <netdev.h>
> > >>> +#include <asm/gpio.h>
> > >>> #include <asm/io.h>
> > >>> #include <asm/arch/cpu.h>
> > >>> #include <asm/arch/soc.h>
> > >>> @@ -111,9 +112,39 @@ int board_early_init_f(void)
> > >>>
> > >>> int board_init(void)
> > >>> {
> > >>> + struct udevice *gpio0;
> > >>> + struct gpio_desc phy_reset;
> > >>> + int ret;
> > >>> +
> > >>> /* Address of boot parameters */
> > >>> gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
> > >>>
> > >
> > > From here
> > >>> + ret = uclass_get_device_by_name(UCLASS_GPIO,
> > >>> + "gpio@18100",
> > >>> + &gpio0);
> > >>> + if (ret < 0) {
> > >>> + printf("Failed to find gpio@18100 node.\n");
> > >>> + return ret;
> > >>> + }
> > >>> +
> > >>> + phy_reset.dev = gpio0;
> > >>> +
> > >>> + /* MPP19 controls the uSOM onboard phy reset */
> > >>> + phy_reset.offset = 19;
> > >>> +
> > > up until this line can be replaced by a single line
> > > ret = dm_gpio_lookup_name("A19", &reset);
> > >
> > > but gpio "A19" does not correlate with any documentation
> > > (datasheet, schematic, or device tree).
> > > I also got this warning
> > > "Device 'gpio@18100': seq 0 is in use by 'gpio-expander@20'"
> > >
> > >>> + ret = dm_gpio_request(&phy_reset, "phy-reset");
> > >>> + if (ret)
> > >>> + return ret;
> > >>> +
> > >>> + dm_gpio_set_dir_flags(&phy_reset,
> > >>> + GPIOD_IS_OUT |
> > >>> + GPIOD_ACTIVE_LOW |
> > >>> + GPIOD_IS_OUT_ACTIVE);
> > >>> +
> > >>> + mdelay(10);
> > >>> + dm_gpio_set_value(&phy_reset, 0);
> > >>> + mdelay(10);
> > >>> +
> > >>
> > >> Hmm, this is a pretty complex and unusual way to use the GPIO.
> > >> Please use the DT to describe the PHY reset GPIO instead. And since
> > >> it seems to be a common issue to have such a PHY reset GPIO, it
> > >> would be better to integrate this into the ethernet driver instead.
> > >
> > > well, I followed minnowmax implementation
> > > (board/intel/minnowmax/minnowmax.c) and some other boards.
> >
> > This seems not to be a good example. It's pretty outdated, AFAICT.
> >
> > > Maybe I should use named gpios in the device tree.
> >
> > Yes. As mentioned above, please look at the mvpp2 driver. And e.g.
> > at the armada-8040-clearfog-gt-8k.dts DT file:
> >
> > /* 1G SGMII */
> > &cps_eth1 {
> > status = "okay";
> > phy-mode = "sgmii";
> > phy = <&phy0>;
> > phy-reset-gpios = <&cpm_gpio1 11 GPIO_ACTIVE_LOW>;
> > };
> >
> > Here you see, how the GPIO is defined in the DT. It should not
> > be too hard to get this implemented in the mvneta driver as well.
> >
> Yes, what I meant is to put "phy-reset-gpios" in the device tree but it
> would still part of the system reset so the reset would be asserted in
> board_init.
>
> If the reset implemented in driver (mvneta), the reset would only
> asserted when u-boot going to use the network interface. This is not
> desirable.
Network device probe routine is always called even when not used. See this
comment in eth_initialize():
/*
* Devices need to write the hwaddr even if not started so that Linux
* will have access to the hwaddr that u-boot stored for the device.
* This is accomplished by attempting to probe each device and calling
* their write_hwaddr() operation.
*/
baruch
--
http://baruch.siach.name/blog/ ~. .~ Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
- bar...@tkos.co.il - tel: +972.2.679.5364, http://www.tkos.co.il -
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
