Hi Wolfgang
I tried with kermit again.
Following is the console log when file is getting transfered.
###################################
C-Kermit 8.0.211, 10 Apr 2004, chetan-laptop
Current Directory: /media/DISK_VOL2/Work/beagleboard/sw/code/testApp
Communication Device: /dev/ttyUSB0
Communication Speed: 115200
Parity: none
RTT/Timeout: 01 / 02
SENDING: uImage => uImage
File Type: BINARY
File Size: 1911160
Percent Done: 2 /
...10...20...30...40...50...60...70...80...90..100
Estimated Time Left: 00:05:38
Transfer Rate, CPS: 5512
Window Slots: 1 of 1
Packet Type: D
Packet Count: 79
Packet Length: 609
Error Count: 32
Last Error: (resend)
Last Message:
X to cancel file, Z to cancel group, <CR> to resend last packet,
############################
As there is considerable difference between the logs I am getting and logs
you have provided in you last mail.
e.g Communication device is /dev/ttyUSB0 (in my logs)
But in your case it look like:
Network Host: ts0:513
Network Type: TCP/IP
I am not sure about these differences.
~cnanda
On Sun, Jan 31, 2010 at 8:43 PM, Wolfgang Denk <w...@denx.de> wrote:
> Dear Chetan Nanda,
>
> In message <7f245da81001310646x12451ac8s5ac9bda0fd6ac...@mail.gmail.com>
> you wrote:
> >
> > Tried with loady command in u-boot and ymodem option from minicom.
> > With this combination I am able to transfer and run uImage.
>
> I tested this again on OMAP3 systems (including Beagle):
>
> OMAP3 beagleboard.org # loadb ${uimage_addr}
> ## Ready for binary (kermit) download to 0x80300000 at 115200 bps...
>
> (Back at pollux.denx.de)
> ----------------------------------------------------
> Kermit>send /bin /tftpboot/beagle/uImage
> ...
> C-Kermit 8.0.211, 10 Apr 2004, pollux.denx.de [192.168.1.1]
>
> Current Directory: /home/wd
> Network Host: ts0:513
> Network Type: TCP/IP
> Parity: none
> RTT/Timeout: 01 / 02
> SENDING: /tftpboot/beagle/uImage => uImage
> File Type: BINARY
> File Size: 1962820
> Percent Done: 99 /////////////////////////////////////////////////-
> ...10...20...30...40...50...60...70...80...90..100
> Estimated Time Left: 00:00:02
> Transfer Rate, CPS: 4748
> Window Slots: 1 of 1
> Packet Type: D
> Packet Count: 2459
> Packet Length: 1000
> Error Count: 0
> Last Error:
> Last Message:
>
> X to cancel file, Z to cancel group, <CR> to resend last packet,
> E to send Error packet, ^C to quit immediately, ^L to refresh screen.
> ...
> Kermit>c
> Connecting to host ts0:513
> Escape character: Ctrl-\ (ASCII 28, FS): enabled
> Type the escape character followed by C to get back,
> or followed by ? to see other options.
> ----------------------------------------------------
> ## Total Size = 0x001df344 = 1962820 Bytes
> ## Start Addr = 0x80300000
> OMAP3 beagleboard.org # imi 0x80300000
>
> ## Checking Image at 80300000 ...
> Legacy image found
> Image Name: Linux-2.6.33-rc5-07168-gc48807a
> Created: 2010-01-25 14:58:56 UTC
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 1962756 Bytes = 1.9 MB
> Load Address: 80008000
> Entry Point: 80008000
> Verifying Checksum ... OK
> OMAP3 beagleboard.org #
>
> As you can see, this is working without any problems.
>
> So either your host systems is still misconfigured (which I consoder
> most likely), or your target system hast issues (instable RAM and.or
> serial port, etc.), or you have been doing something wrong.
>
> I don't think there is a problem in the mainline U-Boot code.
>
> Best regards,
>
> Wolfgang Denk
>
> --
> DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: w...@denx.de
> If I can have honesty, it's easier to overlook mistakes.
> -- Kirk, "Space Seed", stardate 3141.9
>
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
