Hello all,
I am seeing u-boot crash, while I run the latest u-boot on LS1088 for
SD-Boot(ls1088aqds_sdcard_qspi_defconfig).
There were some changes related to passing env-parameters introduced by commit
"8a3a7e2270b39f14c1778a574bb815068d8c74d4 env: Pass additional parameters
to the env lookup function".
Did anyone face similar issue?
I reached this commit("8a3a7e22") after running git bisect.
Log embedded in below mail chain.
Regards
Ashish
> -----Original Message-----
> From: Ashish Kumar
> Sent: Thursday, February 8, 2018 3:51 PM
> To: Maxime Ripard <maxime.rip...@bootlin.com>; York Sun
> <york....@nxp.com>
> Cc: Pankit Garg <pankit.g...@nxp.com>
> Subject: RE: Crash observed while running Uboot
>
> Hello York, Maxime,
>
> I am seeing this u-boot crash on top of the tree of denx.de.
> After running git bisect, I found this commit
> "8a3a7e2270b39f14c1778a574bb815068d8c74d4 env: Pass additional
> " introduces it. Any idea how to fix?
>
> Logs below:
> U-Boot 2018.03-rc1-00185-g9b2cfe2 (Feb 08 2018 - 15:45:34 +0530)
>
> SoC: LS1088AE Rev1.0 (0x87030010)
> Clock Configuration:
> CPU0(A53):1600 MHz CPU1(A53):1600 MHz CPU2(A53):1600 MHz
> CPU3(A53):1600 MHz CPU4(A53):1600 MHz CPU5(A53):1600 MHz
> CPU6(A53):1600 MHz CPU7(A53):1600 MHz
> Bus: 700 MHz DDR: 2100 MT/s
> Reset Configuration Word (RCW):
> 00000000: 4000541c 00000040 00000000 00000000
> 00000010: 00000000 000a0000 00300000 00000000
> 00000020: 01001150 00002580 00000000 00000040
> 00000030: 00000c5b 00000000 00000000 00000000
> 00000040: 00000000 00000000 00000000 00000000
> 00000050: 00000000 00000000 00000000 00000000
> 00000060: 00000000 00000000 00000011 000009e7
> 00000070: 44110000 00009555
> I2C: ready
> DRAM: Initializing DDR....using SPD
> Detected UDIMM 18ASF1G72AZ-2G1A1
> 7.9 GiB
> DDR 7.9 GiB (DDR4, 64-bit, CL=15, ECC on)
> FSL_SDHC: 0
> SEC Firmware: config-1: no such config
> SEC Firmware: error (-2)
> SEC Firmware: Failed to load image
> WARN: pls set popts->cpo_sample = 0x6a in <board>/ddr.c to optimize cpo
> Waking secondary cores to start from fbd51000 All (8) cores are up.
> Using SERDES1 Protocol: 29 (0x1d)
> Using SERDES2 Protocol: 13 (0xd)
> NAND: 0 MiB
> MMC: Loading Environment from MMC... OK
> EEPROM: Invalid ID (ff ff ff ff)
> In: serial
> Out: serial
> Err: serial
> Model: NXP Layerscape 1088a QDS Board
> Board: LS1088A-QDS, Board Arch: V1, Board version: B, boot from SD card
> vBank: 0
> FPGA: v6 (LS1088AQDS_2016_0818_1311), build 75 on Thu Aug 18 18:11:20 2016
> SERDES1 Reference : Clock1 = 100MHz Clock2 = 156.25MHz
> SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz SATA link 0 timeout.
> AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
> flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst Found 0
> device(s).
> SCSI: Net: qds: WRIOP: Supported SerDes1 Protocol 0x1d
> PCIe0: pcie@3400000 Root Complex: no link
> PCIe1: pcie@3500000 Root Complex: no link
> PCIe2: pcie@3600000 Root Complex: x1 gen1
> e1000: 00:1b:21:39:30:86
> DPMAC1@xgmii
> Warning: DPMAC1@xgmii (eth0) using random MAC address - fe:89:69:1c:38:4f ,
> DPMAC2@xgmii
> Warning: DPMAC2@xgmii (eth1) using random MAC address - 96:82:07:2f:7f:b0
> , DPMAC3@qsgmii
> Warning: DPMAC3@qsgmii (eth2) using random MAC address -
> 92:ba:99:eb:1b:fd , DPMAC4@qsgmii
> Warning: DPMAC4@qsgmii (eth3) using random MAC address - fa:b1:f7:d8:5c:02
> , DPMAC5@qsgmii
> Warning: DPMAC5@qsgmii (eth4) using random MAC address -
> c2:ea:0a:78:b5:0a , DPMAC6@qsgmii
> Warning: DPMAC6@qsgmii (eth5) using random MAC address -
> ca:e2:23:02:39:06 , DPMAC7@qsgmii
> Warning: DPMAC7@qsgmii (eth6) using random MAC address -
> 92:1f:76:1e:82:97 , DPMAC8@qsgmii
> Warning: DPMAC8@qsgmii (eth7) using random MAC address -
> 9a:17:5f:64:0e:9b , DPMAC9@qsgmii
> Warning: DPMAC9@qsgmii (eth8) using random MAC address -
> a2:4c:a2:c4:e7:93 , DPMAC10@qsgmii
> Warning: DPMAC10@qsgmii (eth9) using random MAC address -
> aa:44:8b:be:6b:9f , e1000#0 [PRIME]
> Device: FSL_SDHC
> Manufacturer ID: 74
> OEM: 4a45
> Name: SDC
> Bus Speed: 50000000
> Mode : SD High Speed (50MHz)
> card capabilities: widths [4, 1] modes [SD Legacy, SD High Speed (50MHz)] host
> capabilities: widths [8, 4, 1] modes [MMC legacy, SD Legacy, MMC High Speed
> (26MHz), SD High Speed (50MHz), MMC High Speed (52MHz)] Rd Block Len: 512
> SD version 3.0 High Capacity: Yes
> Capacity: 3.7 GiB
> Bus Width: 4-bit
> Erase Group Size: 512 Bytes
>
> MMC read: dev # 0, block # 20480, count 2048 ... 2048 blocks read: OK
>
> MMC read: dev # 0, block # 28672, count 2048 ... 2048 blocks read: OK
> crc32+ "Synchronous Abort" handler, esr 0x96000045
> ELR: 80462fac
> LR: 8043cde8
> x0 : 0000008240000000 x1 : 00000000800000c8
> x2 : 00000000000d0f68 x3 : 0000000000000000
> x4 : 000000000001a1ed x5 : 00000000000d0f68
> x6 : 60c7847000e08070 x7 : 0000000000000003
> x8 : 0000000000000084 x9 : 000000000000000c
> x10: 00000000fbb4ab5c x11: 0000000080000000
> x12: 000000000000005b x13: 00000000000d1080
> x14: 00000000fbb4ab7c x15: 0000000080000000
> x16: 00000000fbdbf35f x17: 00000000fbdcf7e5
> x18: 00000000fbb4cd88 x19: 0000008240000000
> x20: 00000000000d0f68 x21: 0000000000000007
> x22: 0000000080100000 x23: 00000000fbde5e54
> x24: 0000000000000005 x25: 0000000000000000
> x26: 0000000000000000 x27: 0000000000000000
> x28: 00000000fbb57520 x29: 00000000fbb4ac40
>
> > -----Original Message-----
> > From: Pankit Garg
> > Sent: Tuesday, February 6, 2018 11:03 AM
> > To: Maxime Ripard <maxime.rip...@bootlin.com>
> > Cc: Ashish Kumar <ashish.ku...@nxp.com>
> > Subject: RE: Crash observed while running Uboot
> >
> > Hi Maxime Ripard,
> >
> > We are using ls1088aqds_sdcard_qspi_defconfig.
> > When we are trying to read from mmc we are getting this error.
> >
> > Best Regards,
> > Pankit Garg.
> >
> > -----Original Message-----
> > From: Maxime Ripard [mailto:maxime.rip...@bootlin.com]
> > Sent: Monday, February 5, 2018 7:24 PM
> > To: Pankit Garg <pankit.g...@nxp.com>
> > Cc: Ashish Kumar <ashish.ku...@nxp.com>
> > Subject: Re: Crash observed while running Uboot
> >
> > Hi Pankit,
> >
> > On Mon, Feb 05, 2018 at 01:07:48PM +0000, Pankit Garg wrote:
> > > I am getting crash while running Uboot(cloned code from Upstream
> > > Repo) on LS1088aqds board .
> > >
> > > I ran git bisect and find below commit id as Bad patch.
> > >
> > > 8a3a7e2270b39f14c1778a574bb815068d8c74d4 env: Pass additional
> > parameters to
> > > the env lookup function
> > >
> > > Any idea ,what is going wrong or how I can proceed further ?
> >
> > Which configuration are you using?
> >
> > Thanks!
> > Maxime
> >
> > --
> > Maxime Ripard, Bootlin (formerly Free Electrons) Embedded Linux and
> > Kernel engineering http://bootlin.com
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
