Hello York, This fixes the crash on LS1088 sd-boot.
Regards Ashish > -----Original Message----- > From: York Sun > Sent: Friday, February 16, 2018 9:21 PM > To: Ashish Kumar <ashish.ku...@nxp.com>; u-boot@lists.denx.de > Cc: Pankit Garg <pankit.g...@nxp.com>; Maxime Ripard > <maxime.rip...@bootlin.com> > Subject: Re: Crash observed while running U-Boot on LS1088 SD-boot > > Ashish, > > Please check if this fixes it https://patchwork.ozlabs.org/patch/870653/ > > York > > On 02/16/2018 02:57 AM, Ashish Kumar wrote: > > Hello all, > > > > I am seeing u-boot crash, while I run the latest u-boot on LS1088 for SD- > Boot(ls1088aqds_sdcard_qspi_defconfig). > > There were some changes related to passing env-parameters introduced by > commit > > "8a3a7e2270b39f14c1778a574bb815068d8c74d4 env: Pass additional > parameters to the env lookup function". > > > > Did anyone face similar issue? > > I reached this commit("8a3a7e22") after running git bisect. > > > > Log embedded in below mail chain. > > > > Regards > > Ashish > >> -----Original Message----- > >> From: Ashish Kumar > >> Sent: Thursday, February 8, 2018 3:51 PM > >> To: Maxime Ripard <maxime.rip...@bootlin.com>; York Sun > >> <york....@nxp.com> > >> Cc: Pankit Garg <pankit.g...@nxp.com> > >> Subject: RE: Crash observed while running Uboot > >> > >> Hello York, Maxime, > >> > >> I am seeing this u-boot crash on top of the tree of denx.de. > >> After running git bisect, I found this commit > >> "8a3a7e2270b39f14c1778a574bb815068d8c74d4 env: Pass additional > >> " introduces it. Any idea how to fix? > >> > >> Logs below: > >> U-Boot 2018.03-rc1-00185-g9b2cfe2 (Feb 08 2018 - 15:45:34 +0530) > >> > >> SoC: LS1088AE Rev1.0 (0x87030010) > >> Clock Configuration: > >> CPU0(A53):1600 MHz CPU1(A53):1600 MHz CPU2(A53):1600 MHz > >> CPU3(A53):1600 MHz CPU4(A53):1600 MHz CPU5(A53):1600 MHz > >> CPU6(A53):1600 MHz CPU7(A53):1600 MHz > >> Bus: 700 MHz DDR: 2100 MT/s > >> Reset Configuration Word (RCW): > >> 00000000: 4000541c 00000040 00000000 00000000 > >> 00000010: 00000000 000a0000 00300000 00000000 > >> 00000020: 01001150 00002580 00000000 00000040 > >> 00000030: 00000c5b 00000000 00000000 00000000 > >> 00000040: 00000000 00000000 00000000 00000000 > >> 00000050: 00000000 00000000 00000000 00000000 > >> 00000060: 00000000 00000000 00000011 000009e7 > >> 00000070: 44110000 00009555 > >> I2C: ready > >> DRAM: Initializing DDR....using SPD > >> Detected UDIMM 18ASF1G72AZ-2G1A1 > >> 7.9 GiB > >> DDR 7.9 GiB (DDR4, 64-bit, CL=15, ECC on) > >> FSL_SDHC: 0 > >> SEC Firmware: config-1: no such config SEC Firmware: error (-2) SEC > >> Firmware: Failed to load image > >> WARN: pls set popts->cpo_sample = 0x6a in <board>/ddr.c to optimize > >> cpo Waking secondary cores to start from fbd51000 All (8) cores are up. > >> Using SERDES1 Protocol: 29 (0x1d) > >> Using SERDES2 Protocol: 13 (0xd) > >> NAND: 0 MiB > >> MMC: Loading Environment from MMC... OK > >> EEPROM: Invalid ID (ff ff ff ff) > >> In: serial > >> Out: serial > >> Err: serial > >> Model: NXP Layerscape 1088a QDS Board > >> Board: LS1088A-QDS, Board Arch: V1, Board version: B, boot from SD > >> card > >> vBank: 0 > >> FPGA: v6 (LS1088AQDS_2016_0818_1311), build 75 on Thu Aug 18 18:11:20 > >> 2016 > >> SERDES1 Reference : Clock1 = 100MHz Clock2 = 156.25MHz > >> SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz SATA link 0 timeout. > >> AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode > >> flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst Found 0 > >> device(s). > >> SCSI: Net: qds: WRIOP: Supported SerDes1 Protocol 0x1d > >> PCIe0: pcie@3400000 Root Complex: no link > >> PCIe1: pcie@3500000 Root Complex: no link > >> PCIe2: pcie@3600000 Root Complex: x1 gen1 > >> e1000: 00:1b:21:39:30:86 > >> DPMAC1@xgmii > >> Warning: DPMAC1@xgmii (eth0) using random MAC address - > >> fe:89:69:1c:38:4f , DPMAC2@xgmii > >> Warning: DPMAC2@xgmii (eth1) using random MAC address - > >> 96:82:07:2f:7f:b0 , DPMAC3@qsgmii > >> Warning: DPMAC3@qsgmii (eth2) using random MAC address - > >> 92:ba:99:eb:1b:fd , DPMAC4@qsgmii > >> Warning: DPMAC4@qsgmii (eth3) using random MAC address - > >> fa:b1:f7:d8:5c:02 , DPMAC5@qsgmii > >> Warning: DPMAC5@qsgmii (eth4) using random MAC address - > >> c2:ea:0a:78:b5:0a , DPMAC6@qsgmii > >> Warning: DPMAC6@qsgmii (eth5) using random MAC address - > >> ca:e2:23:02:39:06 , DPMAC7@qsgmii > >> Warning: DPMAC7@qsgmii (eth6) using random MAC address - > >> 92:1f:76:1e:82:97 , DPMAC8@qsgmii > >> Warning: DPMAC8@qsgmii (eth7) using random MAC address - > >> 9a:17:5f:64:0e:9b , DPMAC9@qsgmii > >> Warning: DPMAC9@qsgmii (eth8) using random MAC address - > >> a2:4c:a2:c4:e7:93 , DPMAC10@qsgmii > >> Warning: DPMAC10@qsgmii (eth9) using random MAC address - > >> aa:44:8b:be:6b:9f , e1000#0 [PRIME] > >> Device: FSL_SDHC > >> Manufacturer ID: 74 > >> OEM: 4a45 > >> Name: SDC > >> Bus Speed: 50000000 > >> Mode : SD High Speed (50MHz) > >> card capabilities: widths [4, 1] modes [SD Legacy, SD High Speed > >> (50MHz)] host > >> capabilities: widths [8, 4, 1] modes [MMC legacy, SD Legacy, MMC High > >> Speed (26MHz), SD High Speed (50MHz), MMC High Speed (52MHz)] Rd > >> Block Len: 512 SD version 3.0 High Capacity: Yes > >> Capacity: 3.7 GiB > >> Bus Width: 4-bit > >> Erase Group Size: 512 Bytes > >> > >> MMC read: dev # 0, block # 20480, count 2048 ... 2048 blocks read: OK > >> > >> MMC read: dev # 0, block # 28672, count 2048 ... 2048 blocks read: OK > >> crc32+ "Synchronous Abort" handler, esr 0x96000045 > >> ELR: 80462fac > >> LR: 8043cde8 > >> x0 : 0000008240000000 x1 : 00000000800000c8 > >> x2 : 00000000000d0f68 x3 : 0000000000000000 > >> x4 : 000000000001a1ed x5 : 00000000000d0f68 > >> x6 : 60c7847000e08070 x7 : 0000000000000003 > >> x8 : 0000000000000084 x9 : 000000000000000c > >> x10: 00000000fbb4ab5c x11: 0000000080000000 > >> x12: 000000000000005b x13: 00000000000d1080 > >> x14: 00000000fbb4ab7c x15: 0000000080000000 > >> x16: 00000000fbdbf35f x17: 00000000fbdcf7e5 > >> x18: 00000000fbb4cd88 x19: 0000008240000000 > >> x20: 00000000000d0f68 x21: 0000000000000007 > >> x22: 0000000080100000 x23: 00000000fbde5e54 > >> x24: 0000000000000005 x25: 0000000000000000 > >> x26: 0000000000000000 x27: 0000000000000000 > >> x28: 00000000fbb57520 x29: 00000000fbb4ac40 > >> > >>> -----Original Message----- > >>> From: Pankit Garg > >>> Sent: Tuesday, February 6, 2018 11:03 AM > >>> To: Maxime Ripard <maxime.rip...@bootlin.com> > >>> Cc: Ashish Kumar <ashish.ku...@nxp.com> > >>> Subject: RE: Crash observed while running Uboot > >>> > >>> Hi Maxime Ripard, > >>> > >>> We are using ls1088aqds_sdcard_qspi_defconfig. > >>> When we are trying to read from mmc we are getting this error. > >>> > >>> Best Regards, > >>> Pankit Garg. > >>> > >>> -----Original Message----- > >>> From: Maxime Ripard [mailto:maxime.rip...@bootlin.com] > >>> Sent: Monday, February 5, 2018 7:24 PM > >>> To: Pankit Garg <pankit.g...@nxp.com> > >>> Cc: Ashish Kumar <ashish.ku...@nxp.com> > >>> Subject: Re: Crash observed while running Uboot > >>> > >>> Hi Pankit, > >>> > >>> On Mon, Feb 05, 2018 at 01:07:48PM +0000, Pankit Garg wrote: > >>>> I am getting crash while running Uboot(cloned code from Upstream > >>>> Repo) on LS1088aqds board . > >>>> > >>>> I ran git bisect and find below commit id as Bad patch. > >>>> > >>>> 8a3a7e2270b39f14c1778a574bb815068d8c74d4 env: Pass additional > >>> parameters to > >>>> the env lookup function > >>>> > >>>> Any idea ,what is going wrong or how I can proceed further ? > >>> > >>> Which configuration are you using? > >>> > >>> Thanks! > >>> Maxime > >>> > >>> -- > >>> Maxime Ripard, Bootlin (formerly Free Electrons) Embedded Linux and > >>> Kernel engineering http://bootlin.com > > _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
