Hi Jonathan, > On Sat, Feb 03, 2018 at 11:00:35AM -0200, Fabio Estevam wrote: > > On Sat, Feb 3, 2018 at 5:29 AM, Lukasz Majewski <lu...@denx.de> > > wrote: > > > The goal of this patch is to clean up the code related to > > > choosing SPL MMC boot mode. > > > > > > The spl_boot_mode() now is called only in spl_mmc_load_image() > > > function, which is only compiled in if CONFIG_SPL_MMC_SUPPORT is > > > enabled. > > > > > > To achieve the goal, all per mach/arch implementations eligible > > > for unification has been replaced with one __weak implementation. > > > > > > Signed-off-by: Lukasz Majewski <lu...@denx.de> > > > Reviewed-by: Marek Vasut <ma...@denx.de> > > > Reviewed-by: Stefano Babic <sba...@denx.de> > > > Acked-by: Michal Simek <michal.si...@xilinx.com> (For ZynqMP) > > > > Nice cleanup: > > > > Reviewed-by: Fabio Estevam <fabio.este...@nxp.com> > > This has broken booting via mmc with mx6cuboxi for me. > > SPL loops on > > U-Boot SPL 2018.03-rc1-00212-g48914fc119 (Feb 10 2018 - 11:04:33 > +1300) Trying to boot from MMC1 > Failed to mount ext2 filesystem... > spl_load_image_ext: ext4fs mount err - 0
Could you check what is the status of following defines in your .config file: CONFIG_SPL_FAT_SUPPORT CONFIG_SUPPORT_EMMC_BOOT And if by any chance your don't have: CONFIG_SPL_EXT_SUPPORT defined? From what you have written above I assume that you boot from the same medium - i.e. eMMC (so SPL and u-boot.img are on the same medium) ? Best regards, Łukasz Majewski > > There is no ext2/ext3/ext4 fs, next U-Boot stage is raw, ie > > dd if=mx6cuboxi/SPL of=/dev/sd2c bs=1024 seek=1 > dd if=mx6cuboxi/u-boot.img of=/dev/sd2c bs=1024 seek=69 > > => part list mmc 0 > > Partition Map for MMC device 0 -- Partition Type: DOS > > Part Start Sector Num Sectors UUID Type > 1 2048 32768 00000000-01 0c Boot > 4 34816 15642624 00000000-04 a6 > > With this commit reverted: > > U-Boot SPL 2018.03-rc1-00214-ge3f2485203 (Feb 10 2018 - 12:38:46 > +1300) Trying to boot from MMC1 > > > U-Boot 2018.03-rc1-00214-ge3f2485203 (Feb 10 2018 - 12:38:46 +1300) > > CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz) > CPU: Extended Commercial temperature grade (-20C to 105C) at 27C > Reset cause: POR > Board: MX6 Cubox-i > DRAM: 2 GiB > MMC: FSL_SDHC: 0 > Loading Environment from MMC... OK > No panel detected: default to HDMI > Display: HDMI (1024x768) > In: serial > Out: serial > Err: serial > Net: FEC > Hit any key to stop autoboot: 0 > switch to partitions #0, OK > mmc0 is current device > Scanning mmc 0:1... > 37503 bytes read in 18 ms (2 MiB/s) > Found EFI removable media binary efi/boot/bootarm.efi > Scanning disks on usb... > Disk usb0 not ready > Disk usb1 not ready > Disk usb2 not ready > Disk usb3 not ready > Scanning disks on mmc... > MMC Device 1 not found > MMC Device 2 not found > MMC Device 3 not found > Scanning disks on sata... > Disk sata0 not ready > Found 3 disks > 76528 bytes read in 30 ms (2.4 MiB/s) > ## Starting EFI application at 12000000 ... > >> OpenBSD/armv7 BOOTARM 1.0 > boot> > booting sd0a:/bsd: 4531856+203028+560156 > [277405+90+281904+244582]=0x5d6b88 Best regards, Lukasz Majewski -- DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: w...@denx.de
pgp2z7p_p4_c4.pgp
Description: OpenPGP digital signature
_______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
