On Wed, Sep 28, 2016 at 2:30 PM, Jagan Teki <jagannadh.t...@gmail.com> wrote:
> On Thu, Sep 29, 2016 at 12:51 AM, Joe Hershberger
> <joe.hershber...@gmail.com> wrote:
>> On Wed, Sep 28, 2016 at 2:15 PM, Jagan Teki <jagannadh.t...@gmail.com> wrote:
>>> On Thu, Sep 29, 2016 at 12:41 AM, Joe Hershberger
>>> <joe.hershber...@gmail.com> wrote:
>>>> On Wed, Sep 28, 2016 at 1:28 PM, Jagan Teki <jt...@openedev.com> wrote:
>>>>> From: Jagan Teki <ja...@amarulasolutions.com>
>>>>>
>>>>> Add enet support for engicam icorem6 qdl starter kit.
>>>>> - Add pinmux settings
>>>>> - Add board_eth_init
>>>>>
>>>>> TFTP log:
>>>>> --------
>>>>> Net: FEC [PRIME]
>>>>> Hit any key to stop autoboot: 0
>>>>> icorem6qdl> tftpboot {fdt_addr} imx6dl-icore.dtb
>>>>> Using FEC device
>>>>> TFTP from server 192.168.2.96; our IP address is 192.168.2.75
>>>>> Filename 'imx6dl-icore.dtb'.
>>>>> Load address: 0x0
>>>>> Loading: ######
>>>>> 1.3 MiB/s
>>>>> done
>>>>> Bytes transferred = 28976 (7130 hex)
>>>>> CACHE: Misaligned operation at range [00000000, 00007130]
>>>>> icorem6qdl>
>>>>>
>>>>> Cc: Joe Hershberger <joe.hershber...@ni.com>
>>>>> Cc: Peng Fan <peng....@nxp.com>
>>>>> Cc: Stefano Babic <sba...@denx.de>
>>>>> Cc: Fabio Estevam <fabio.este...@nxp.com>
>>>>> Cc: Matteo Lisi <matteo.l...@engicam.com>
>>>>> Cc: Michael Trimarchi <mich...@amarulasolutions.com>
>>>>> Signed-off-by: Jagan Teki <ja...@amarulasolutions.com>
>>>>> ---
>>>>> board/engicam/icorem6/icorem6.c | 72
>>>>> +++++++++++++++++++++++++++++++++++++
>>>>> configs/imx6qdl_icore_mmc_defconfig | 4 +++
>>>>> include/configs/imx6qdl_icore.h | 12 +++++++
>>>>> 3 files changed, 88 insertions(+)
>>>>>
>>>>
>>>> ...
>>>>
>>>>> diff --git a/configs/imx6qdl_icore_mmc_defconfig
>>>>> b/configs/imx6qdl_icore_mmc_defconfig
>>>>> index a658f4b..d304693 100644
>>>>> --- a/configs/imx6qdl_icore_mmc_defconfig
>>>>> +++ b/configs/imx6qdl_icore_mmc_defconfig
>>>>> @@ -14,6 +14,8 @@ CONFIG_SYS_MAXARGS=32
>>>>> # CONFIG_CMD_IMLS is not set
>>>>> CONFIG_CMD_BOOTZ=y
>>>>> CONFIG_CMD_GPIO=y
>>>>> +CONFIG_CMD_MII=y
>>>>> +CONFIG_CMD_PING=y
>>>>> CONFIG_CMD_MEMTEST=y
>>>>> CONFIG_CMD_MMC=y
>>>>> CONFIG_CMD_CACHE=y
>>>>> @@ -23,5 +25,7 @@ CONFIG_CMD_EXT4_WRITE=y
>>>>> CONFIG_CMD_FAT=y
>>>>> CONFIG_CMD_FS_GENERIC=y
>>>>> CONFIG_OF_LIBFDT=y
>>>>> +CONFIG_FEC_MXC=y
>>>>> CONFIG_MXC_UART=y
>>>>> +CONFIG_NETDEVICES=y
>>>>> CONFIG_IMX_THERMAL=y
>>>>
>>>> I guess this board can't use CONFIG_DM_ETH for some reason?
>>>
>>> True I will remove and send the patch.
>>
>> I assume you mean you'll switch the board to enable CONFIG_DM_ETH? Not
>> sure what you mean when you say you will remove (something) when my
>> comment was about the absence of a config.
>
> Sorry, I am not planning to use DM_ETH as of now. Since all net
> drivers in Kconfig are in if CONFIG_NETDEVICES. ie the reason I added.
> I think this is needed in defconfig.
CONFIG_NETDEVICES certainly is needed if you don't specify
CONFIG_DM_ETH. I prefer new board support use DM_ETH. What's the
reason for not using DM?
Thanks,
-Joe
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
