On Wed, Sep 28, 2016 at 2:15 PM, Jagan Teki <jagannadh.t...@gmail.com> wrote:
> On Thu, Sep 29, 2016 at 12:41 AM, Joe Hershberger
> <joe.hershber...@gmail.com> wrote:
>> On Wed, Sep 28, 2016 at 1:28 PM, Jagan Teki <jt...@openedev.com> wrote:
>>> From: Jagan Teki <ja...@amarulasolutions.com>
>>>
>>> Add enet support for engicam icorem6 qdl starter kit.
>>> - Add pinmux settings
>>> - Add board_eth_init
>>>
>>> TFTP log:
>>> --------
>>> Net: FEC [PRIME]
>>> Hit any key to stop autoboot: 0
>>> icorem6qdl> tftpboot {fdt_addr} imx6dl-icore.dtb
>>> Using FEC device
>>> TFTP from server 192.168.2.96; our IP address is 192.168.2.75
>>> Filename 'imx6dl-icore.dtb'.
>>> Load address: 0x0
>>> Loading: ######
>>> 1.3 MiB/s
>>> done
>>> Bytes transferred = 28976 (7130 hex)
>>> CACHE: Misaligned operation at range [00000000, 00007130]
>>> icorem6qdl>
>>>
>>> Cc: Joe Hershberger <joe.hershber...@ni.com>
>>> Cc: Peng Fan <peng....@nxp.com>
>>> Cc: Stefano Babic <sba...@denx.de>
>>> Cc: Fabio Estevam <fabio.este...@nxp.com>
>>> Cc: Matteo Lisi <matteo.l...@engicam.com>
>>> Cc: Michael Trimarchi <mich...@amarulasolutions.com>
>>> Signed-off-by: Jagan Teki <ja...@amarulasolutions.com>
>>> ---
>>> board/engicam/icorem6/icorem6.c | 72
>>> +++++++++++++++++++++++++++++++++++++
>>> configs/imx6qdl_icore_mmc_defconfig | 4 +++
>>> include/configs/imx6qdl_icore.h | 12 +++++++
>>> 3 files changed, 88 insertions(+)
>>>
>>
>> ...
>>
>>> diff --git a/configs/imx6qdl_icore_mmc_defconfig
>>> b/configs/imx6qdl_icore_mmc_defconfig
>>> index a658f4b..d304693 100644
>>> --- a/configs/imx6qdl_icore_mmc_defconfig
>>> +++ b/configs/imx6qdl_icore_mmc_defconfig
>>> @@ -14,6 +14,8 @@ CONFIG_SYS_MAXARGS=32
>>> # CONFIG_CMD_IMLS is not set
>>> CONFIG_CMD_BOOTZ=y
>>> CONFIG_CMD_GPIO=y
>>> +CONFIG_CMD_MII=y
>>> +CONFIG_CMD_PING=y
>>> CONFIG_CMD_MEMTEST=y
>>> CONFIG_CMD_MMC=y
>>> CONFIG_CMD_CACHE=y
>>> @@ -23,5 +25,7 @@ CONFIG_CMD_EXT4_WRITE=y
>>> CONFIG_CMD_FAT=y
>>> CONFIG_CMD_FS_GENERIC=y
>>> CONFIG_OF_LIBFDT=y
>>> +CONFIG_FEC_MXC=y
>>> CONFIG_MXC_UART=y
>>> +CONFIG_NETDEVICES=y
>>> CONFIG_IMX_THERMAL=y
>>
>> I guess this board can't use CONFIG_DM_ETH for some reason?
>
> True I will remove and send the patch.
I assume you mean you'll switch the board to enable CONFIG_DM_ETH? Not
sure what you mean when you say you will remove (something) when my
comment was about the absence of a config.
Thanks,
-Joe
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
