On Thu, Sep 29, 2016 at 12:51 AM, Joe Hershberger
<joe.hershber...@gmail.com> wrote:
> On Wed, Sep 28, 2016 at 2:15 PM, Jagan Teki <jagannadh.t...@gmail.com> wrote:
>> On Thu, Sep 29, 2016 at 12:41 AM, Joe Hershberger
>> <joe.hershber...@gmail.com> wrote:
>>> On Wed, Sep 28, 2016 at 1:28 PM, Jagan Teki <jt...@openedev.com> wrote:
>>>> From: Jagan Teki <ja...@amarulasolutions.com>
>>>>
>>>> Add enet support for engicam icorem6 qdl starter kit.
>>>> - Add pinmux settings
>>>> - Add board_eth_init
>>>>
>>>> TFTP log:
>>>> --------
>>>> Net: FEC [PRIME]
>>>> Hit any key to stop autoboot: 0
>>>> icorem6qdl> tftpboot {fdt_addr} imx6dl-icore.dtb
>>>> Using FEC device
>>>> TFTP from server 192.168.2.96; our IP address is 192.168.2.75
>>>> Filename 'imx6dl-icore.dtb'.
>>>> Load address: 0x0
>>>> Loading: ######
>>>> 1.3 MiB/s
>>>> done
>>>> Bytes transferred = 28976 (7130 hex)
>>>> CACHE: Misaligned operation at range [00000000, 00007130]
>>>> icorem6qdl>
>>>>
>>>> Cc: Joe Hershberger <joe.hershber...@ni.com>
>>>> Cc: Peng Fan <peng....@nxp.com>
>>>> Cc: Stefano Babic <sba...@denx.de>
>>>> Cc: Fabio Estevam <fabio.este...@nxp.com>
>>>> Cc: Matteo Lisi <matteo.l...@engicam.com>
>>>> Cc: Michael Trimarchi <mich...@amarulasolutions.com>
>>>> Signed-off-by: Jagan Teki <ja...@amarulasolutions.com>
>>>> ---
>>>> board/engicam/icorem6/icorem6.c | 72
>>>> +++++++++++++++++++++++++++++++++++++
>>>> configs/imx6qdl_icore_mmc_defconfig | 4 +++
>>>> include/configs/imx6qdl_icore.h | 12 +++++++
>>>> 3 files changed, 88 insertions(+)
>>>>
>>>
>>> ...
>>>
>>>> diff --git a/configs/imx6qdl_icore_mmc_defconfig
>>>> b/configs/imx6qdl_icore_mmc_defconfig
>>>> index a658f4b..d304693 100644
>>>> --- a/configs/imx6qdl_icore_mmc_defconfig
>>>> +++ b/configs/imx6qdl_icore_mmc_defconfig
>>>> @@ -14,6 +14,8 @@ CONFIG_SYS_MAXARGS=32
>>>> # CONFIG_CMD_IMLS is not set
>>>> CONFIG_CMD_BOOTZ=y
>>>> CONFIG_CMD_GPIO=y
>>>> +CONFIG_CMD_MII=y
>>>> +CONFIG_CMD_PING=y
>>>> CONFIG_CMD_MEMTEST=y
>>>> CONFIG_CMD_MMC=y
>>>> CONFIG_CMD_CACHE=y
>>>> @@ -23,5 +25,7 @@ CONFIG_CMD_EXT4_WRITE=y
>>>> CONFIG_CMD_FAT=y
>>>> CONFIG_CMD_FS_GENERIC=y
>>>> CONFIG_OF_LIBFDT=y
>>>> +CONFIG_FEC_MXC=y
>>>> CONFIG_MXC_UART=y
>>>> +CONFIG_NETDEVICES=y
>>>> CONFIG_IMX_THERMAL=y
>>>
>>> I guess this board can't use CONFIG_DM_ETH for some reason?
>>
>> True I will remove and send the patch.
>
> I assume you mean you'll switch the board to enable CONFIG_DM_ETH? Not
> sure what you mean when you say you will remove (something) when my
> comment was about the absence of a config.
Sorry, I am not planning to use DM_ETH as of now. Since all net
drivers in Kconfig are in if CONFIG_NETDEVICES. ie the reason I added.
I think this is needed in defconfig.
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
